Furniture of America CM3318PC-2PK User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-03-05
Page 1 of 5
DIFFICULT
ASSEMBLY RATING
CM3318PC-2PK
Phillips Screwdriver
(Not Included)

Page 2 of 5

Parts List Hardware List
#1 x 1 pc
Backrest w/Legs
#2 x 1 pc
Seat Frame w/Cushion
#3 x 1 pc
Left Front Leg
#A x 10 pcs
Flat Washer 1/4”
#B x 10 pcs
Lock Washer 1/4”
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 2 pcs
Bolt 1/4”x1-1/2”
MD
#D x 4 pcs
Bolt 1/4”x2-3/8”
Page 3 of 5
#E x 4 pcs
Bolt 1/4”x3”
#F x 1 pc
Allen Wrench
Note: The above parts and hardware are shown for a complete
assembly of ONE chair. However, the actual parts and hardware
(with an exception of the Allen wrench) in the box will be twice the
quantities listed to include the assembly of the second chair.
#4 x 1 pc
Right Front Leg
#5 x 1 pc
Front Leg Support
#6 x 1 pc
Left Leg Support
#7 x 1 pc
Right Leg Support #G x 6 pcs
Wood Screw

Step 1 I. Place the backrest with legs (#1) on a protected surface.
II. Align the seat frame with cushion (#2) with the pre-drilled holes of
the backrest with legs (#1).
III. Prepare 2 bolt assemblies by inserting FIRST the lock washer (#B)
onto the bolt (#C) and then the flat washer (#A) onto the SAME bolt
(#C), in that order.
IV. Insert the bolt assemblies through the two pre-drilled holes of the
seat frame with cushion (#2) and secure those bolts using the Allen
wrench (#F) to lock it in with the backrest with legs (#1).
Step 2
Turn right (clockwise) to tighten
Enlarged
Page 4 of 5
#A x 2 pcs
#B x 2 pcs
#C x 2 pcs
I. Prepare 4 bolt assemblies by inserting FIRST the lock
washer (#B) onto the bolt (#E) and then the flat washer (#A)
onto the SAME bolt (#E), in that order.
II. Insert 2 bolt assemblies through the two pre-drilled holes in
the corner of the seat frame with cushion (#2) and secure
those bolts using the Allen wrench (#F) to lock it in with the
backrest with legs (#1). Repeat for the other side.
#A x 4 pcs
#B x 4 pcs
#E x 4 pcs
Enlarged
Turn right (clockwise) to tighten

Step 3
I. Align the left front leg (#3) with the
two pre-drilled holes of the seat
frame with cushion (#2).
II. Prepare 2 bolt assemblies by
inserting FIRST the lock washer
(#B) onto the bolt (#D) and then
the flat washer (#A) onto the
SAME bolt (#D), in that order.
III. Insert 2 bolt assemblies through
the two pre-drilled holes in the
corner of the seat frame with
cushion (#2) and secure those
bolts using the Allen wrench (#F) to
lock it in with the left front leg (#3).
IV. Repeat the process above for the
right front leg (#4).
Step 4
Turn right (clockwise) to tighten
Page 5 of 5
#A x 4 pcs
#B x 4 pcs
#D x 4 pcs
ASSEMBLE EVERYTHING EXACTLY THE SAME FOR THE SECOND CHAIR
#2
Note: Right and left is determined by standing in FRONT of the chair
in its upright position.
Enlarged
6 Locations
I. Insert the front leg support (#5) between the left
front leg (#3) and the right front leg (#4). Attach
those parts together with two wood screws (#G)
using a Phillips screwdriver to lock in the front leg
support (#5) with the left front leg (#3) AND the right
front leg (#4).
II. Insert the left leg support (#6) between the backrest
with legs (#1) and the left front leg (#3). Attach
those parts together with two wood screws (#G)
using a Phillips screwdriver to lock in the left leg
support (#6) with the backrest with legs (#1) AND
the left front leg (#3).
III. Repeat process II for the right leg support (#7).
IV. Carefully turn the completed chair upright. Make
sure the chair is rested on a flat surface and it does
not feel loose or wobbly. If it does, double check
that the bolts are secured and properly tighten.
#1
Turn right (clockwise) to tighten
Enlarged