Furniture of America CM7016 F User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM7016 F / Q
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-11-18
Page 1 of 7
DIFFICULT
ASSEMBLY RATING
2 PERSONS RECOMMENDED
Wrench
(Not Included)

Page 2 of 7

#4 x 1 pc
Footboard
Parts List
#1 x 1 pc
Headboard
#3 x 2 pcs
Side Rail
#7 x 26 pcs
Slat
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
MD
Page 3 of 7
#6 x 4 pcs
HB/FB Leg
#2R x 1 pc
Right H/B Side
#5 x 1 pc
Support Rail
#8 x 2 pcs
Support Rail Leg
Note: Right and left are determined
by facing the front of the bed in the
upright position.
#2L x 1 pc
Left H/B Side

#D x 28 pcs
Lock Washer
Hardware List
#A x 8 pcs
Bolt 5/16”x2”
#C x 4 pcs
Bolt 5/16”x2-1/2”
#G x 26 pcs
End Cap
Due to the size and/or weight of this product, it is
highly recommended that the assembly should be
done near the area of its intended location. Make
sure you have enough space to move around
during the assembly. ALWAYS have at least two
people to help with transporting and assembling the
product to avoid any potential injury and/or damage.
Page 4 of 7
#I x 1 pc
Wrench
#F x 13 pcs
Center Connector
#J x 4 pcs
Hex Nut
#B x 16 pcs
Bolt 5/16”x1-1/2”
#E x 28 pcs
Flat Washer
#H x 1 pc
Allen Wrench

Page 5 of 7
I. Align the right H/B side (#2R) with
the pre-drilled holes on the right
side of the headboard (#1).
II. Prepare 4 bolt assemblies by
inserting FIRST the lock washer
(#D) onto the bolt (#A) and then
the flat washer (#E) onto the
SAME bolt (#A), in that order.
III. Insert the bolt assemblies through
the pre-drilled holes of the
headboard (#1) using the Allen
wrench (#H) to lock them with the
right H/B side (#2R).
IV. Repeat the process above to
assemble the left H/B side (#2L)
onto the headboard (#1). Turn right (clockwise) to tighten
#2R
#2L
#A x 8 pcs
#D x 8 pcs
#E x 8 pcs
I. Align the two HB/FB legs (#6)
with the pre-drilled holes
underneath the headboard
(#1).
II. Prepare 2 bolt assemblies by
inserting FIRST the lock
washer (#D) onto the bolt
(#C) and then the flat washer
(#E) onto the SAME bolt
(#C), in that order.
III. Insert the bolt assemblies
through the holes of the two
HB/FB legs (#6) and secure
those bolts using the Allen
wrench (#H) to lock them with
the headboard (#1).
IV. Repeat the process above to
assemble the remaining two
HB/FB legs (#6) onto the
footboard (#4).
#C x 4 pcs
#D x 4 pcs
#E x 4 pcs
#6
Turn right (clockwise) to tighten

Turn right (clockwise) to tighten
Page 6 of 7
#B x 4 pcs
#D x 4 pcs
#E x 4 pcs
#J x 4 pcs
#B x 8 pcs
#D x 8 pcs
#E x 8 pcs
I. Align the 2 support rail legs (#8) with the pre-drilled holes of the support rail
(#5).
II. Prepare 4 bolt assemblies by inserting FIRST the lock washer (#D) onto
the bolt (#B) and then the flat washer (#E) onto the SAME bolt (#B), in that
order.
III. Insert the bolt assemblies through the pre-drilled holes of the support rail
(#5) and the 2 slat support legs (#8) using the Allen wrench (#H).
IV. Tighten the 4 hex nuts (#J) onto the same bolts (#B) using the wrench (#I)
to secure the parts together.
I. Prepare 4 bolt assemblies by
inserting FIRST the lock washer
(#D) onto the bolt (#B) and then
the flat washer (#E) onto the
SAME bolt (#B), in that order.
II. Insert the bolt assemblies
through the pre-drilled holes of
the right and the left side of the
headboard (#1) using the Allen
wrench (#H) but expose about
½” of the bolts’ threads.
III. Mount the brackets on the 2 side
rails (#3) onto the bolts (#B).
Make sure all the washers are in
the FRONT of the brackets. Use
the Allen wrench (#H) to further
tighten the bolts to secure the
two parts together.
IV. Repeat the process above to
assemble the other ends of the 2
side rails (#3) onto the footboard
(#4).
Turn right (clockwise) to tighten
Adjust the levelers on Step 5.

Page7of7
I. Align the assembled support rail (#5) with the pre-drilled holes on the center
of the headboard (#1) and the footboard (#4).
II. Prepare 4 bolt assemblies by inserting FIRST the lock washer (#D) onto the
bolt (#B) and then the flat washer (#E) onto the SAME bolt (#B), in that
order.
III. Insert the bolt assemblies through the brackets of the support rail (#5) using
the Allen wrench (#H) to lock them with the headboard (#1) and the
footboard (#4).
#B x 4 pcs
#D x 4 pcs
#E x 4 pcs Turn right (clockwise) to tighten
#F x 13 pcs
#G x 26 pcs
I. Prepare a bed slat using two
slats (#7), one center connector
(#F) and two end caps (#G).
See diagram for the correct
sequence in connecting those
parts.
II. Align the two end caps (#G)
with the pre-drilled holes on
each side of the side rails (#3)
and press firmly down on both
end caps (#G) to lock with the
side rails (#3). Then press firmly
down on the center connector
(#F) to lock with the support rail
(#5).
III. Repeat the process above to
assemble the remaining bed
slats onto the side rails (#3) and
the support rail (#5).
IV. Make sure the bed is rested on
a flat surface and does not feel
loose or wobbly. If it does,
double check that the
bolts/screws are secured and
properly tightened.
Note: The correct position of the bed
slats should be arcing UPWARD when
placing on the rails.
ASSEMBLY IS COMPLETED
Adjust the levelers according to
the ground level. To lower or to
raise the slat support legs, turn the
leveler clockwise or
counterclockwise, respectively.

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM7016CK-EK
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-09-30
Page 1 of 7
DIFFICULT
ASSEMBLY RATING
2 PERSONS RECOMMENDED
Wrench
(Not Included)

Page 2 of 7

#4 x 1 pc
Footboard
Parts List
#1 x 1 pc
Headboard
#3 x 2 pcs
Side Rail
#7 x 39 pcs
Slat
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
MD
Page 3 of 7
#6 x 4 pcs
HB/FB Leg
#2R x 1 pc
Right H/B Side
#5 x 2 pcs
Support Rail
#8 x 4 pcs
Support Rail Leg
Note: Right and left are determined
by facing the front of the bed in the
upright position.
#2L x 1 pc
Left H/B Side