Furniture of America CM7811D User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM7811D
Assembly Instructions
Tools Required for Assembly:
Rev.14-03-17
Page 1 of 6
DIFFICULT
ASSEMBLY RATING
2 PERSONS RECOMMENDED
Allen Wrench (Included)
CM7811M
DRESSER AND MIRRORARE SOLD AND PACKED SEPARATELY

Page 2 of 6

Parts List
#1 x 1 pc
Dresser
#2 x 2 pcs
Front Leg w/Leveler
#3 x 2 pcs
Rear Leg
#A x 8 pcs
Bolt 1/4”x1-1/2”
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
MD
Page 3 of 6
Hardware List
#D x 1 pc
Allen Wrench
#C x 8 pcs
Flat Washer
#B x 8 pcs
Lock Washer
DRESSER AND MIRROR ARE SOLD AND PACKED SEPARATELY
#4 x 1 pc
Mirror
#5 x 2 pcs
Mirror Support Rails
#6 x 1 pc
Support Leg
#7 x 2 pcs
Shelf

Step 1
Page 4 of 6
Turn right (clockwise) to tighten
Due to the size and weight of this product, it is
highly recommended that the assembly should be
done near the area of its intended location. Make
sure you have enough space to move around during
the assembly. ALWAYS have at least two people to
help with transporting and assembling the product
and to avoid any potential injury and/or damage,
especially with the fragile nature of the mirror.
With the help of another person, carefully place the
dresser (#1) on its back on a protected surface. Align
the threaded end of the front legs with levelers (#2)AND
the rear legs (#3) with the pre-drilled holes on the bottom
of the dresser (#1) and tighten by hand until secured.

Step 2
Page 5 of 6
Enlarged
Turn right (clockwise) to tighten
I. The two mirror support brackets (#5) are already attached behind the
dresser. Position the mirror support brackets (#5) vertically to align with the
pre-drilled hole of the dresser (#1) AND the mirror (#4).
II. Prepare 6 bolt assemblies by inserting FIRST the lock washer (#B) onto the
bolt (#A) and then the flat washer (#C) onto the SAME bolt (#A), in that
order.
III. Insert those bolt assemblies onto the mirror support brackets (#5) and
secure those bolts using an Allen wrench (#D) to lock the mirror support
brackets (#2) with the dresser (#1) AND the mirror (#4).
IV. Tighten all bolts, including those that were already attached from the factory.
Back Side
Back Side
Step 3
Align the threaded end of the support leg (#6) with
the pre-drilled hole on the bottom of the dresser (#1)
and tighten by hand until secured.
Enlarged
Turn right (clockwise) to tighten
#A x 8 pcs
#B x 8 pcs
#C x 8 pcs

Step 4
Page 6 of 6
Enlarged
Adjust the leveler according to the ground level. To
lower or to raise the support leg (#6), you need to
turn the leveler clockwise or counterclockwise,
respectively.
Step 5
ASSEMBLY IS COMPLETED
Tilt the shelf (#7) at an angle and gently have it rested
and leveled on top of the shelf supports. Repeat the
process for the other shelf (#7).
Adjust the leveler according to the
ground level. To lower or to raise the
front leg, you need to turn the leveler
clockwise or counterclockwise,
respectively.