Furniture of America Dion CM7361CK User manual

AssemblyInstructions
EASY DIFFICULT
Page 1 of7
ASSEMBLYRATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product(with 1 being
easy and 5 being difficult).For some
products,two persons are recommended.
Rev: 18-03-23
CM7361Q/EK/CK
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench (Included)
Phillips Screwdriver
(Not Included)
For more information contact our team: [email protected]

Page2 of 7
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjustment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches.Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.

Parts List
Hardware List
#1 x 1pc
#2 x 2pcs
#4 x 2pcs
#A x 6pcs
Bolt 1/4"x2"
#E x 8pcs
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
HeadboardPanel
#3 x 1pc
Page3 of 7
HeadboardLegs(L/R)
Footboard
Support Leg126x35x35mm
#5 x 2pcs
#6 x 1pc
Center Slat
#7 x 1set
Slat (13pcs)
#8 x 4pcs
Side Rail
Support Leg351x35x35mm
#D x 8pcs
Bolt5/16"x1-3/4"
#F x 8pcs
#G x 1pc
Allen Wrench M4
#H x 26pcs
Screw #8x25mm
#B x 6pcs
#C x 6pcs
Lock Washer Ø1/4"
Flat Washer Ø1/4"
Lock Washer Ø5/16"
Flat Washer Ø5/16"

#1
#2L
#3
#8
#6
#7
#5
#4
#5
#2R
Page4 of 7
#9 x 2pcs
Dusty Panel
Parts List
Hardware List
#I x 8pcs
Screw #8 x 15mm
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
#9
#9

Page5 of 7
#A
#C
#B
#G
#1
#2L
#A x 6pcs
#B x 6pcs
#C x 6pcs
#2R
#4
#3
Align HB legs (#2R/L) to the holes of the headboard (#1), then
secure by using bolts (#A) with washers (#B,C).
Attach support legs (#4) to the holes of the footboard (#3). Adjust the
leveler on the support legs (#4) according to ground level.

Page6 of 7
#1
#2L
#5
#3
#D x 8pcs
#E x 8pcs
#F x 8pcs
#5
#2R
#E
#F
#D
#G
#6
#8
#7
Align side rails (#5) to the holes of the HB legs (#2R/L) and footboard (#3).
Secure by using bolts (#D) with washers (#E,F).
Align center slat (#6) to the holes of the slat set (#7), then
secure by attaching support legs (#8) to center slat (#6) and
slat set (#7). Adjust levelers of the support legs (#8)
according to ground level.

#H
#H x 26pcs
#5
#5
#7
USB
Page7 of 7
#I x 8pcs
#I
#9
#7
#9
Align slat set (#7) to the side rails (#5),
then secure by using screws (#H).
Align dusty panels (#9) to the bed slats, then secure by using screws (#I).