Furniture of America HFW-1468C5 User manual

HFW-1468C5
Page 1 of 12 REV.14-09-23

Page 2 of 12

Page 3 of 12

Page 4 of 12

Page 5 of 12
CAM LOCK FASTENER ASSEMBLY INSTRUCTIONS

COFFEE TABLE
ASSEMBLY INSTRUCTIONS MODEL # HFW-1468C5
please keep for future reference PARTS LIST
HARDWARE LIST
116PCS 216PCS 378PCS 48PCS 53PCS 64PCS
7 8
DIMENSIONS : 47.2"(W)*23.6"(D)16.9"(H)
Page 6 of 12
2SETS(8pcs) 16PCS 9 10 1PC 11 10PCS8PCS
B1PC
A1PC
P2PCS
O2PCS
N2PCS
M2PCS
L2PCS
E1PC
D1PCC1PC
F1PC
H3PCS
G2PCS
I8PCS J2PCS
K1PCS
DL
B
K
L

STEP : 1
L
L
Hardware 1 x 4 pcs
Hardware 2 x 4 pcs
Hardware 3 x 4 pcs
Hardware 4 x 8 pcs
Hardware 7 x 4 pcs drawer rails
Hardware 8 x 8 pcs
Dowel hole
ASSEMBLY INSTRUCTIONS
Page 7 of 12
Left Drawer Rail
Side View
Right Drawer Rail
Front View
Identifying Drawer's Rails (a.k.a. Runners, Glides, Slides or Guides)
An assembly of ONE drawer requires a set of 4 different rails: right panel rail, left panel rail, right
drawer rail and left drawer rail. To identify which rail belongs to which part, please read completely
first before assembling.
To Determine Right/Left Panel Rail: Place the panel rail flat on its back with the roller position on
the left hand side. If there are two holes above the roller and the other end is slightly downward angle
then it is the LEFT PANEL RAIL. If there are two holes below the roller and the other end is slightly
upward angle, then it is the RIGHT PANEL RAIL. The right and left panel rails are mirror image of
each other.If needed, label or separate each rail for easy identification.
To Determine Right/Left Drawer Rail: Place the drawer rail with the round and oval holes resting
flat on the surface with its roller on the right hand side. If the roller is facing the top, then it is the
LEFT DRAWER RAIL and if the roller is facing the bottom, then it is the RIGHT DRAWER RAIL. The
right and left drawer rails are mirror image of each other. If needed, label or separate each rail for
easy identification.
Mounting the Panel Rail: The panel rail is constructed to be mounted flat. Make sure the roller is
position on the front of the panel and the screw holes are aligned with the pre-drilled holes of the
panel.
Mounting the Drawer Rail: The drawer rail is constructed to be mounted on the side of the drawer .
Make sure the roller is position on the SIDE REAR of the drawer and the screw holes are aligned
with the pre-drilled holes on the side of the drawer.

ASSEMBLY INSTRUCTIONS
STEP : 2
STEP : 3
Page 8 of 12
Hardware 3 x 40 pcs
Hardware 3 x 16 pcs
Hardware 7 x 4 pcs panel rails
Hardware 8 x 8 pcs
J
X 8
Dowel hole
D
Dowel hole
3
8
7
Left Panel Rail
Left Panel Rail Right Panel Rail

ASSEMBLY INSTRUCTIONS
STEP : 4
STEP : 5
Page 9 of 12
Hardware 9 x 8 pcs
Dowel hole
JE
I
I
I
C

ASSEMBLY INSTRUCTIONS
STEP : 7
Page 10 of 12
Hardware 1 x 4 pcs
STEP : 6
X 3
H
Hardware 3 x 18 pcs
H
H
H
G
G