Furniture of America YNJ-1507 User manual

ASSEMBLY RATING
The Assembly Rating is a 5-point
system that shows the degree of effort
needed in assembling a specific
product (with 1 being easy and 5 being
difficult). For most products, two
persons are recommended.
EASY DIFFICULT
Page 1
ASSEMBLY INSTRUCTIONS
Tools Required for Assembly
Phillips Screwdriver
Allen Wrench
(Not Included)
( Included)
2 PERSON RECOMMENDED
Hammer
(Not Included)

Page 3

Unless you are particularly adept at assembling flat-pack/knock-down
furniture, we understand building ready-to-assemble furniture can be a
frustrating experience for some. To help avoid confusion and to make
the assembly process quicker and smoother, we have provided some
helpful tips. Before you begin the assembly, please read the following:
1. Due to the size and/or weight on most of the ready-to-assemble furniture, it is
highly recommended that the assembly should be done near the area of its
intended location. Make sure you have enough space to move around during
the assembly. ALWAYS have at least two people to help with transporting and
assembling of the product to avoid any potential injury and/or damage.
2. To protect from damage, assemble the item on a clean, protective surface,
such as on a carpet or cardboard.
3. Make sure you have taken all the parts and hardware out of their packaging.
Do not throw away packaging material until assembly is completed.
4. Make sure all parts and hardware are accounted for by comparing the actual
parts and hardware to the list provided in the assembly instructions. Also
check for any irregularity such as crack, flaw or improperly drilled hole. If there
is any problem or missing piece, please contact the manufacturer or the
supplier. Please have the model number, part number and a brief description
of the problem ready will help expedite the replacement process.
5. Read the entire instruction manual and view the diagrams first before
assembling. Arrange your parts in order of use and group the identical
hardware together to make it easier to grab each piece as you begin to
assemble.
6. During the assembly process, make sure all parts are properly aligned before
tightening with the tool provided or required for the assembly. Do not use
power tools and do not over tighten.
7. When applying glue to the wood dowels to bond the parts together, please be
ABSOLUTELY certain that the parts are correct and lined up with each other
(refer to diagrams and take notice of the various pre-drilled hole locations).
When in doubt, assemble the parts together first and if the parts fit right, then
apply glue to the wood dowels.
PRE-ASSEMBLY INTRODUCTION
Page 4

CAM LOCK FASTENER ASSEMBLY INSTRUCTIONS
ly
Page 5

HARDWARE LIST
PARTS LIST
132PCS 32PCS
VANITY
ASSEMBLY INSTRUCTIONS
2
49.21“ (W) X16.73" (D) X31.54" (H)
DIMENSIONS
Before you begin, please
read "Assembly and
Care Advice","Pre-
Assembly Introduction"
and "Cam Lock Fastener
Assembly Instructions"
Page 6
10 2PCS 11 1PC
6 7 8PCS12PCS 4PCS32PCS 424PCS 6PCS 8
5
3
94PCS 13 1Set 14 1PC
12 12PCS
A1PC B1PC C1PC D1PC E1PC F1PC
G1PC H1PC 1PC
I1PC
JK1PC
15 4PCS 16 4PCS
A
H
G
B
EW
49.21"
16.73"
31.54"
L1PC
M1PC N3PCS O1PC P1PC Q1PC R1PC S2PCS
T2PCS U2PCS V2PCS W1PC X1PC Y1PC
Z1PC a1PC b1PC c1PC d2PCS e1PC

ASSEMBLY INSTRUCTIONS
Page 7
STEP1
Hardware #1=15pcs
Hardware #7=4pcs
Assembling Drawer’s Runners (a.k.a. Rails, Glides, Slides or Guides)
An assembly of ONE drawer requires two sets of runners. The runner is
composed of an inner rail and outer slide. Please read completely first before
assembling.
Mounting the Inner Rail (Fixed) of the Runner:
Before mounting, please determine which side of the panel is the front and rear.
The single screw hole on the outer slide MUST be positioned on the FRONT of
the panel. Place the inner rail of the runner in its correct position and flat on its
back. Slide the outer slide out to the way to align the center or second holes on
both ends of the inner rail with the pre-drilled holes on the panel. For most
applications, the center or second holes are used but if not, just make sure the
appropriate rail holes are aligned up with the panel holes. Use two screws to
secure the inner rail of the runner onto the panel.
Mounting the Outer Slide (Moveable) of the Runner:
Each outer rail is secured with a single screw onto the FRONT SIDE of the
drawer. Extend the two outer slides of the runners and place the drawer in
between those two outer slides. Align the pre-drilled holes on each side of the
drawer with the screw holes of the outer slides. Use two screws to secure from
the inside of the drawer into the screw holes of the outer slides.
Hardware #3=3pcs
2nd Hole
7
8
C
7
10
8
12
1
10
7
Front
Front
2nd Hole
8
7
E
B
Front
14
3
F
3
Screw Hole
Front
Hardware #8=8pcs
Hardware #10=2pcs
Hardware #12=4pcs
12
8

ASSEMBLY INSTRUCTIONS
Page 8
STEP2
Hardware #2=12pcs
Hardware #1=3pcs
Hardware #3=8pcs
G
1
3
MN
X3
14
3
1
2
Hardware #1=5pcs
Hardware #3=6pcs
STEP3
Hardware #2=5pcs
J
D
I
D
J
F
5
Hardware #5=4pcs
H
1
3
H
I
2
J
C
c
N
N
N
M
G
E
11111111
2

Page 9
ASSEMBLY INSTRUCTIONS
Hardware #2=6pcs
Hardware #5=6pcs
STEP4
Hardware #3=6pcs
JB
KO
1
2
K
O
2
B
C
14
3
L
3
Hardware #1=4pcs
Hardware #3=4pcs
STEP5
Hardware #2=4pcs
5
T
X2
S
X2
11111111
U
X2
3
V
X2
Hardware #4=8pcs
T
U
S
d
2
6
Hardware #6=6pcs
4

Page 10
ASSEMBLY INSTRUCTIONS
Hardware #1=5pcs
Hardware #3=5pcs
STEP6
Hardware #2=5pcs
1
W
Y
b
X
32
b
Y
X
W
e
a
12
a
1
2
14
3
Hardware #4=12pcs
Z
4
Hardware #12=4pcs
Hardware #4=4pcs
Hardware #5=2pcs
STEP7
Hardware #13=1set
Q
P
R
4
13
A
A
5
P
QR

Page 11
ASSEMBLY INSTRUCTIONS
Hardware #9=4pcs
Hardware #12=4pcs
STEP8
A
12
Extend the two outer slides
of the runners so that they
are align with the sides of
the drawer. Make sure the
pre-drilled holes from the
drawer align with the screw
holes of the outer slides.
Secure two screws from the
inside of the drawer using a
Phillips screwdriver to tighten
them to the outer slides.
ASSEMBLY IS COMPLETED
Make sure the product is rested on a flat surface and does not feel loose or wobbly. If it does, double
check that the bolts/screws are secured and properly tightened.
9
S
S
W
Hardware #15=4pcs
Hardware #16=4pcs
15
16
11
Hardware #11=1pc