Furuno FAR-3210 User manual

INSTRUCTION MANUAL
SETTING AND ADJUSTMENTS
Model FAR-3210/FAR-3220/FAR-3310/FAR-3320/
FAR-3230S/FAR-3330S/FAR-3320W/FAR-3330SW/
FAR-3230S-SSD/FAR-3330S-SSD/
FAR-3210-BB/FAR-3220-BB/
FAR-3230S-BB/FAR-3230S-SSD-BB/
FAR-3220W-BB/FAR-3230SW-BB
This manual is solely for use by the installer. Under no circumstances
shall this manual be released to the user.
The installer shall remove this manual from the vessel after installation.
This manual contains no password data. Obtain password data from
FURUNO before beginning the installation.
www.furuno.com

www.furuno.com
Pub. No. E32-01305-J
(1907, GREG) FAR-3000 SERIES
Printed in Japan
䢲䢲䢲䢳䢹䢺䢲䢶䢸䢳䢺

i
INTRODUCTION
About this manual
This manual shows how to setup the chart radar after the installation. After setting, make a backup
copy of configuration data onto a medium (PC, etc.).
Preparation
• PC (for the LAN connection, OS: Windows®XP or Windows®7)
• LAN cable (for the LAN connection)
Trademarks
Windows is a registered trademark or trademark of Microsoft Corporation in the United States and/
or other countries.
Silent mode
Use the silent mode when the ECDIS is not required, like in a harbor. This mode deactivates the
audio alarms.
1. Click the [OTHERS] button on the Status bar in the chart mode then click [Silent].
2. Enter “3000”, then click the [OK] button. The following pop-up window appears.
3. To return to normal operation, click the [Back to Normal Mode] button in the pop-up window
shown above.
Click to return to normal operation.

ii
TABLE OF CONTENTS
1. INITIAL SETTING AND ADJUSTMENT ................................................................1-1
1.1 How to Access the Common Installation Settings Menu............................................ 1-1
1.1.1 Laptop PC (LAN connection) access ............................................................. 1-1
1.1.2 Control Unit RCU-024/025/026 ...................................................................... 1-2
1.1.3 [Common Installation Setting] menu contents................................................ 1-3
1.2 [Basic Setting] Menu .................................................................................................. 1-4
1.2.1 [Basic Setting] window ................................................................................... 1-4
1.2.2 [Peripherals] window ...................................................................................... 1-6
1.2.3 [VDR] window................................................................................................. 1-8
1.2.4 [Route Transfer] window ................................................................................ 1-9
1.2.5 [Application] window..................................................................................... 1-10
1.2.6 [Ship Name] window .................................................................................... 1-10
1.2.7 [ECDIS/RADAR] window.............................................................................. 1-11
1.2.8 [Language] window ...................................................................................... 1-11
1.3 [Own Ship Setting] Menu ......................................................................................... 1-12
1.4 [Installation Parameters] Menu ................................................................................ 1-14
1.4.1 Sensor setting .............................................................................................. 1-14
1.4.2 Processor unit configuration.........................................................................1-16
1.4.3 Activating the connection with the processor unit of the
FAR-2xx8 series radar ................................................................................. 1-22
1.4.4 Sensor adapter configuration....................................................................... 1-24
1.4.5 Antenna unit configuration ........................................................................... 1-27
1.4.6 Monitoring of HUB........................................................................................ 1-28
1.4.7 Signal and Port settings for external equipment .......................................... 1-29
1.4.8 Customized sensor setting........................................................................... 1-31
1.4.9 Settings to activate the shuttle ferry mode................................................... 1-32
1.4.10 Installation setting examples........................................................................ 1-33
1.5 [CCRS] Menu ........................................................................................................... 1-35
1.5.1 How to select the [Data Source]................................................................... 1-35
1.5.2 How to set [Transmission Group]................................................................. 1-36
1.5.3 [CCRS Setting] window................................................................................ 1-39
1.6 [TCS] Menu .............................................................................................................. 1-39
1.7 [AMS] Menu ............................................................................................................. 1-40
1.8 [Alert Define List] Menu............................................................................................ 1-42
1.8.1 Alert Group Setting....................................................................................... 1-42
1.8.2 How to add an alert group............................................................................ 1-43
1.8.3 How to edit an alert group............................................................................ 1-44
1.8.4 How to delete an alert group........................................................................ 1-45
1.8.5 Alert Definition setting for each equipment .................................................. 1-45
1.8.6 How to add an alert definition....................................................................... 1-47
1.8.7 How to edit an alert definition....................................................................... 1-48
1.8.8 How to delete an alert definition................................................................... 1-48
1.9 [Data Sharing] Menu ................................................................................................ 1-49
1.10 [Save and Sync] Menu ............................................................................................. 1-49
1.10.1 Consistency check and save the configuration............................................ 1-49
1.10.2 How to save the configuration data to a medium......................................... 1-51
1.10.3 How to load the configuration data ..............................................................1-51
1.11 [Radar Installation] Menu ......................................................................................... 1-52
1.12 [System Monitor] Menu ............................................................................................ 1-52
1.13 [Software Update] Menu .......................................................................................... 1-52
1.14 [Factory Test & Default] Menu ................................................................................. 1-53

TABLE OF CONTENTS
iii
1.15 [Conning] Menu ........................................................................................................1-56
1.15.1 How to select the data source ......................................................................1-57
1.15.2 Advanced settings window ...........................................................................1-57
2. SETTING FOR SENSOR ADAPTER.....................................................................2-1
2.1 How to Set the Equipment ID .....................................................................................2-1
2.2 How to Save the Log File ...........................................................................................2-2
2.3 How to Update the Firmware (MC-3000S) .................................................................2-2
2.3.1 How to activate the maintenance program.....................................................2-3
2.3.2 How to confirm the firmware program version................................................2-3
2.3.3 How to update the firmware program .............................................................2-4
3. HUB-3000 IGMP Querier ......................................................................................3-1
APPENDIX 1EQUIPMENT ID List ............................................................................AP-1
APPENDIX 2SUB SYSTEM ......................................................................................AP-3

TABLE OF CONTENTS
iv
This page is intentionally left blank.

1-1
1. INITIAL SETTING AND
ADJUSTMENT
This chapter shows you how to enter the initial settings for the processor unit (EC-
3000) of chart radar after the installation.
Each unit has a default IP address. Enter the initial settings (Equipment ID setting) and
change the IP address on the [Basic Setting] menu (see section 1.2.), before connect-
ing each unit and building the network. After entering the equipment ID(s), build the
network and enter other settings. You can enter the settings of each unit all at one time
by building the network.
1.1 How to Access the Common Installation
Settings Menu
The initial settings for chart radar are performed on the [Common Installation Setting]
menu. The [Common Installation Setting] menu works with a web browser.
Access the [Common Installation Setting] menu by either of the two methods shown
below.
• Access on a laptop PC (LAN connection). See section 1.1.1.
• Access with the control unit RCU-024/025/026. See section 1.1.2.
Note 1: Supported browsers are as follows:
• Internet Explorer®11
• Firefox ESR 60
Note 2: To update the software with the updating file (see section 1.13.), access the
[Common Installation Setting] menu via LAN connection. To update the software with
the DVD, access the [Common Installation Setting] menu with the control unit.
Note 3: When you access the MC-3000S directly from Internet Explorer®, you cannot
adjust the settings on the [Alert Define List] menu. Access either the EC-3000, or use
Firefox to adjust the settings on the [Alert Define List] menu.
1.1.1 Laptop PC (LAN connection) access
1. Set the IP address and subnet mask of the PC according to the LAN port where
the PC is connected.
Note: For the sensor adapter, use the LAN2 port (sensor network).
LAN port IP address/
Subnet mask Setting value
LAN1
(Gateway network)
IP address 192.168.31.200
Subnet mask 255.255.255.0
LAN2
(Sensor network)
IP address 172.31.16.200
Subnet mask 255.255.0.0

1. INITIAL SETTING AND ADJUSTMENT
1-2
2. Connect the PC to the LAN1 or LAN2 port of the processor unit with a LAN cable.
Note: It is possible to connect to the LAN1 or LAN2 port via a LAN hub. However,
to operate from the [Basic Setting] menu, turn off all units except the unit to be set.
Enter settings to processor units one by one.
3. Activate the web browser on the PC.
4. Enter the IP address on the address bar on the browser referring to the table
shown below.
When entering the IP address on the address bar, you are asked to enter ID and
password.
5. Enter the ID and password correctly then select [Login]. The [Common Installation
Setting] menu appears.
1.1.2 Control Unit RCU-024/025/026
1. Click [ ] on the status bar then select [Settings]. The pop-up message shown
below appears.
2. Click [OK] to show the [Settings] menu.
3. Click [SERVICE MODE] on the status bar, and then select [Service Login].
A dialog box for entry of password appears.
4. Enter the password and click [OK]. [Service Mode] is shown at the bottom left po-
sition of the [Settings] window.
For RCU-024: Use the keyboard on the control unit to enter the password.
Access point IP address
For the initial
setting
Gateway
Network
192.168.31.31
Sensor
Network
172.31.16.21
For re-setting
the unit
Gateway
Network
Enter the IP address of the gateway or sen-
sor network according to the Equipment ID
used in the system. See the Equipment ID
list at the back of this manual.

1. INITIAL SETTING AND ADJUSTMENT
1-3
For RCU-025/026: Use the software keyboard on the display to enter the pass-
word.
5. Click [SERVICE MODE] on the status bar, and then select [Common Installation
Setting]. The message shown below appears.
6. Click [OK] to activate the web browser and show the dialog box asking for ID and
password.
7. Enter the ID and password correctly then select [Login]. The [Common Installation
Setting] menu appears.
1.1.3 [Common Installation Setting] menu contents
Note: Click [Exit] to close and logout from the [Common Installation Setting] menu.
You can close and logout by clicking on the web browser. However the menu can
not be re-accessed for a while.
The selected tab is highlighted in blue on the tab bar. The view area and menu bar
change according to the tab selected.
Click [ (or )] at the tab bar to shift the tab to the left (or right).
Note: If the tab bar does not move when clicking either [ (or )], clear the
browser cache.
Tab bar
View area
Info bar
Menu bar*
Click here to close
and logout from the
[Common
Installation Setting]
menu.
*: The items selected show in blue.

1. INITIAL SETTING AND ADJUSTMENT
1-4
*: Adjustment not required.
1.2 [Basic Setting] Menu
1.2.1 [Basic Setting] window
1. Access the [Common Installation Setting] menu and click [Basic Setting] on the
tab bar.
2. Click [Basic Setting] on the menu bar.
Tab name Feature
Basic Setting Sets the Equipment ID, monitor, printer, and own ship information
etc.
Own Ship Setting Enters the ship’s parameter and sensor position.
Installation Parameters Sets the system configuration and input/output data.
CCRS Sets the priority of the sensors and NMEA sentences.
TCS Sets the data format for the route data.
AMS Sets the Alert Management System.
Alert Define List Sets the alerts.
Data Sharing* Sets the interlocking system between units.
Save and Sync Save and synchronize the settings. You can save settings to a me-
dium.
Radar Installation* Sets the radar installation parameters.
System Monitor Confirms the system condition.
Software Update Updates the software.
Factory Test and Default Performs the factory test; restores the default settings.
Conning Configures the layout and data to show on the conning display.
Click . . Click . .
TCSTCS AMSAMSCCRS
Basic SettingBasic Setting Own Ship SettingOwn Ship Setting Installation ParametersInstallation Parameters
TCSTCS AMSAMSCCRSOwn Ship SettingOwn Ship Setting Installation ParametersInstallation Parameters Alert Define ListAlert Define List

1. INITIAL SETTING AND ADJUSTMENT
1-5
3. Select the Equipment ID of the processor unit from the [Equipment ID] pull-down
list. (Setting range: [CRA001] to [CRA004]. Do not select [CRA005] to [CRA010])
The [Equipment Name] and [IP Address] are automatically entered according to
the Equipment ID. For details, see the "EQUIPMENT ID List" at the back of this
manual.
Note 1: Assign a different Equipment ID to each processor unit.
Note 2: [Serial No.] is entered before shipment. If you change the SSD or delete
[Serial No.] by mistake, click the box of [Serial No.] to enter the serial number of
the processor unit.
Note 3: The properties of data transmitted under IEC61162-450 protocol are
changed according to the Equipment ID settings.
• The Processor Unit's SFID, Device No. and Channel change as shown in the
following table.
• When this unit has Back-up ECDIS enabled (see subsection 1.4.2) and Back-
up ECDIS mode is active, the SFID changes as shown below.
*: This SFID is applied to all ECDIS-related functions.
4. Select [FAR-3xx0] from the [Equipment Type No.] pull-down list.
5. Select the Equipment ID of the radar processor unit from the [Equipment ID] pull-
down list. Setting range: [RAS001] (default setting), [RAS002], [RAS003],
[RAS004]. Do not use [RAS005] to [RAS010].
6. Select [FAR-3xx0 MAG] or [FAR-3xx0 SSD] from the [Equipment Type No.] pull-
down list.
7. Select the antenna position from the [Antenna Position] pull-down list.
Settings: [Fore], [Main Top], [Main 2nd], [Main 3rd], [Aft], [Port], [Starboard].
8. Click the box of [Serial No.] to enter the serial number of the radar processor unit.
9. Click [Save] on the info bar. Several confirmation messages appear. Click [OK] to
reboot the system. To discard all changes, click [Discard Changes].
Equipment ID SFID Device No. Channel
CRA001 RA0001 61 1, 2, 3
CRA002 RA0002 62 1, 2, 3
CRA003 RA0003 63 1, 2, 3
CRA004 RA0004 64 1, 2, 3
Back-up ECDIS
is not active
Back-up ECDIS
is active*
RA0001 EI0021
RA0002 EI0022
RA0003 EI0023
RA0004 EI0024
Radar model Equipment Type No.
FAR-3210/3210-BB/3310
FAR-3220/3220-BB/3320
FAR-3230S/3230S-BB/3330S
FAR-3220W-BB/3320W
FAR-3230SW-BB/3330SW
[FAR-3xx0 MAG]
FAR-3230S-SSD/3230S-SSD-BB/3330S-SSD [FAR-3xx0 SSD]

1. INITIAL SETTING AND ADJUSTMENT
1-6
1.2.2 [Peripherals] window
1. Access the [Common Installation Setting] menu and click [Basic Setting] on the
tab bar.
2. Click [Peripherals] on the menu bar.
3. Select the monitor type and resolution connected to the DVI1 port from the [Type
Number] pull-down list of DVI1.
The setting options are as follows:
Note 1: The DVI2 port outputs the display data same as the data of DVI1 port.
• [MU-190 (SXGA)] • [HD 24T22FUD (WUXGA)]
• [MU-231 (SXGA)] • [HD 26T21MMD (WUXGA)]
• [MU-231 (UXGA)] • [HD 26T22MMD (WUXGA)]*2
• [MU-270W (WUXGA)]*1• [HD 26T22FUD (WUXGA)]
• [MU-270W-B (WUXGA)]*1• [HD 27T22FUD (FHD)]*3
• [MU-201CE (SXGA)] • [HD 27T22FUD (WUXGA)]
• [MU-231CE (SXGA)] • [HD 32T22FUD (FHD)]*3
• [MU-231CE (UXGA)]*3• [HD 32T22FUD (WUXGA)]
• [JH 19T14FUD (SXGA)] • [HD 55T22FUD (FHD)]*3
• [JH 20T17FUD (UXGA)] • [HD 55T22FUD (WUXGA)]
• [JH 23T12FUD (UXGA)] • [NI WA460-01.MON.01(FHD)]*3
• [JH 23T14FUD (UXGA)] • [NI WA460-01.MON.01(WUXGA)]
• [JH 26T11MMD (WUXGA)]*2• [NI WA270-01.MON.01-XXFU(FHD)]*3
• [HD 19T21MMD (SXGA)]*2• [NI WA270-01.MON.01-XXFU(WUXGA)]
• [HD 24T21MMD (FHD)]*3• [AHD 119F (SXGA)]*3
• [HD 24T21MMD (WUXGA)]*2• [AHD 119G (SXGA)]*3
• [HD 24T22FUD (FHD)]*3
*1: When the serial number of the MU-270W is “1000-4610-uuuu” or “10uuuu”, se-
lect [MU-270W (WUXGA)]. If not, select [MU-270W-B (WUXGA)].
*2: Do not use for the monitor connected to the DVI1 port. These monitors are avail-
able for the port other than DVI1 port.
*3: Not used.
*2
*1䠖㻌Not used.
*2䠖㻌Shown when Connected is selected in Connection of [Service Gateway].
*1
*1

1. INITIAL SETTING AND ADJUSTMENT
1-7
Note 2: If the MU-201, MU-231CE or the monitor of Hatteland Display is connect-
ed, the optional cable DSUB9P-X2-A-L5M/L10M for brilliance control is required
to connect.
4. Select the monitor type and resolution connected to the DVI3 port from the [Type
Number] pull-down list of DVI3.
When the processor unit is not connected to the VDR or you do not use the dual
display, select [Not Connected (NONE)] and go to step 8.
5. Select the display data to output from the DVI3 port from the [Output Mode] pull-
down list.
6. When one of the following monitors is selected at step 3, click the [Run] button for
[Monitor Color Calibration] to perform the color calibration. For all other monitors,
go to step 8.
“Processing” appears at the next to the [Run] button during the color calibration.
After completing the calibration, check result appears ([Succeeded] or [Failed]).
When the check result is [Succeeded], the following confirmation message ap-
pears. Click the [OK] button to reboot the system and apply the calibration setting.
When the check result is [Failed], retry the color calibration. If the error is not rec-
tified, contact your dealer.
Note: Be sure to perform the color calibration. If the calibration is not performed,
you cannot adjust the monitor brilliance.
7. Access the [Common Installation Setting] menu and open the [Peripherals] win-
dow again.
8. Select the type of the printer from the [Printer Model] pull-down menu.
Setting option Remarks
[Clone] DVI1 to DVI3 ports output the same resolution and display data.
The DVI1 port can switch chart radar and conning display data.
Note 1: When [Clone] is selected, the [Type Number] for DVI1 and
DVI3 port should be same setting option.
Note 2: Set to [Clone] to connect the chart radar with a VDR.
[Independent] Cannot be selected.
• [HD 19T21MMD (SXGA)] • [HD 26T22FUD (WUXGA)]
• [HD 24T21MMD (FHD)] • [HD 27T22FUD (FHD)]
• [HD 24T21MMD (WUXGA)] • [HD 27T22FUD (WUXGA)]
• [HD 24T22FUD (FHD)] • [HD 32T22FUD (FHD)]
• [HD 24T22FUD (WUXGA)] • [HD 32T22FUD (WUXGA)]
• [HD 26T21MMD (WUXGA)] • [HD 55T22FUD (FHD)]
• [HD 26T22MMD (WUXGA)] • [HD 55T22FUD (WUXGA)]
Setting option Remarks
[HP Officejet Pro 8000] Connect the printer to LAN1 port or USB port, and then
set the IP address of the printer to “192.168.31.241”.
For how to set the IP address of the printer, see the op-
erator’s manual of the printer.
[HP Officejet Pro 8100]
[HP Officejet Pro 8210]

1. INITIAL SETTING AND ADJUSTMENT
1-8
Note 1: For no printer, set [Printer Model] to [HP Officejet 100 Mobile].
Note 2: The printer HP Officejet Pro 8000 Enterprise Printer can not be connected
to the processor unit.
9. Select the port that connects the printer from the [Printer Port] pull-down list.
[USB]: Only the processor unit connected to the printer can print.
[Network]: EC-3000s in the same network
can print. The IP address of the printer is
shown on the [Printer] screen. Do not
change the IP address.
10. To automatically print images captured with [Screenshot] function, check the
checkbox for [Auto Print out (SS)].
11. To connect a service gateway, select [Connected] at [Service gateway] then the
IP address and the port number appear below the [Connected] item. Do not
change these settings.
12. Click [Save] on the info bar. Several confirmation messages appear. Click [OK] to
reboot the system. To discard all changes, click [Discard Changes].
1.2.3 [VDR] window
1. Access the [Common Installation Setting] menu and click [Basic Setting] on the
tab bar.
2. Click [VDR] on the menu bar.
[HP Officejet 100 Mobile] Connect the printer to the USB port of the processor
unit.
[HP Officejet 200 Mobile]
Printer Printer Port
HP Officejet 100 Mobile/HP Officejet 200 Mobile USB
HP Officejet Pro 8000/HP Officejet Pro 8100/
HP Officejet Pro 8210
USB, Network
Setting option Remarks

1. INITIAL SETTING AND ADJUSTMENT
1-9
3. To connect a VDR, select [Connected] at [Connection] in [VDR] then set each
items shown in the table below.
4. Click [Save] on the info bar. Several confirmation messages appear. Click [OK] to
reboot the system. To discard all changes, click [Discard Changes].
1.2.4 [Route Transfer] window
1. Access the [Common Installation Setting] menu and click [Basic Setting] on the
tab bar.
2. Click [Route Transfer] on the menu bar.
3. To transfer data to a specified network, select [Connected] from the [Connection]
pull-down list.
4. Click [Save] on the info bar. Several confirmation mes-sages appear. Click [OK]
to reboot the system.
To discard all changes, click [Discard Changes].
Menu item/
interactive field Description
[Monitor] Select the DVI port connected with the VDR.
[Transmit per 15 sec.] Set the number of transmissions in 15 seconds.
[Transmission Rate] Set the transmitting rate.
[Image Format] Set the image format.
[JPEG Quality] Set the quality of JPEG data. Available when [JPEG] is se-
lected for [Image Format].
[Network] Select the network connected with the VDR.
[Transmission Timing] Set the delay timing. The delay is applied regardless of the
Display Mode selected (RADAR or Back-up ECDIS).
[Destination] Set the IP address and port of the destination.
[Source] Set the status and information text, max. 16 characters.
[Location] Set the status and information text, max. 32 characters.
Menu item Description
[Connection] Select [Connected] to transfer the data.
[Transmission Rate] Set the transmission rate.
[Network] Select the destination network for route date.
[Destination] Set the IP address and port of the destination.
[Initial Value of Sequence
No.]
Set the default value for the sequence identifier to
be used when transferring route data via LAN. This
binary value is set in accordance with IEC 61162-
450 regulations.

1. INITIAL SETTING AND ADJUSTMENT
1-10
1.2.5 [Application] window
1. Access the [Common Installation Setting] menu and click [Basic Setting] on the
tab bar.
2. Click [Application] on the menu bar.
3. Select the primary display mode from the [Primary] pull-down list. The primary dis-
play mode is displayed when you start the ECDIS. Also, the working indicator at
the upper right changes according to the setting, and the spinner can be clicked
to return the primary display mode.
Note: [AMS] is not available for this system.
4. Click [Save] on the info bar. Several confirmation messages appear. Click [OK] to
reboot the system. To discard all changes, click [Discard Changes].
1.2.6 [Ship Name] window
1. Access the [Common Installation Setting] menu and click [Basic Setting] on the
tab bar.
2. Click [Ship Name] on the menu bar.
3. Enter your ship information. The data entered here is included in any printing.
[Ship Name]: Own ship’s name.
[Call Sign]: Own ship’s call sign
[IMO No.]: Own ship’s IMO no.
[MMSI]: Own ship’s ID
Note: Chart radar can display own ship’s data input from AIS, on the [Own Ship]
page in the [Nav Status] menu. The data entered here is not reflected to the AIS
data.
4. Click [Save] on the info bar. Several confirmation mes-sages appear. Click [OK]
to reboot the system. To discard all changes, click [Discard Changes].
: No setting
: [ECDIS] is selected.
: [RADAR] is selected.
䠖[Conning] is selected.

1. INITIAL SETTING AND ADJUSTMENT
1-11
1.2.7 [ECDIS/RADAR] window
1.2.8 [Language] window
The menu language for the everyday operating screens can be set to English or Jap-
anese. The [Common Installation Setting] menu has English menus only.
Note: This language setting is synchronized with all processor units on the network.
Reboot the synchronized processor unit(s) to use the selected menu language.
1. Access the [Common Installation Setting] menu and click [Basic Setting] on the
tab bar.
2. Click [Language] on the menu bar.
3. Select the appropriate language.
4. Click [Save] on the info bar. Several confirmation messages appear. Click [OK] to
reboot the system. To discard all changes, click [Discard Changes].
Menu item Description
[Calculate CPA/TCPA] Keep the default setting. Confirm that the checkbox has
no check mark. If there is a check mark, remove it.
[Use Legacy TTM ID] When the checkbox is checked, the TT whose ID is “100”
is output with the ID “0”. This checkbox is used only when
needed. For example, the checkbox may be checked
when a non-Furuno ECDIS is connected.

1. INITIAL SETTING AND ADJUSTMENT
1-12
1.3 [Own Ship Setting] Menu
Enter the information for ship parameters/CCRP, antenna unit, GPS sensor, AIS tran-
sponder, echo sounder (E/S), and SDME sensor. As for the symbol for sensors, there
are six colors to show the priority: white (CCRP), cyan (radar), green (GPS), magenta
(AIS), orange (E/S) and blue (SDME) in that order.
This setting is required when showing own ship and using the chart mode.
1. Access the [Common Installation Setting] menu and click [Own Ship Setting] on
the tab bar.
2. Activate each field and enter own ship’s data, using the table below for reference.
Menu item/interactive field Description
[Vessel Type] Own ship type among [Fast/Super Small], [Fast/
Small], [Slow/Big] and [Super Tanker].
[Ship Length (LOA, m)] Own ship’s length, in meters.
[Ship Width (m)] Own ship’s width, in meters.
[Summer Load Line (m)] Distance between own ship’s hull and the sum-
mer load line, in meters.
[MAX ROT (deg/min)] Own ship’s maximum angular velocity (Rate of
turn).
[Block Coefficient] Own ship’s block coefficient.
[Min Maneuvering Speed (kn)] Minimum maneuvering speed.
[Center of Gravity X(m), Y(m),
Z(m)]
Own ship’s center of gravity, in meters, set by X,
Y and Z axis.
[Pivot Point X(m), Y(m), Z(m)] Own ship’s pivot point, in meters, set by X, Y and
Z axis. Approximately 80% of the ship’s length is
recommended for the pivot point. For example,
the ship’s length is 350 m, enter "280 m" to [Y
(m)].
[CCRP X(m), Y(m), Z(m)] Select the [CCRP] you wish to setup by left-click-
ing the check box to the left of each CCRP num-
ber. You can set up a maximum of four CCRP
positions. Set up of [CCRP1] is required.

1. INITIAL SETTING AND ADJUSTMENT
1-13
3. Click [Radar Antenna] on the menu bar.
Note: When you set the value for [Antenna Position] on the [Installation Parame-
ters] menu, the setting value is shown at the right of [Equipment ID].
4. According to the number of antenna units connected to the processor unit, check
applicable checkbox to activate the antenna unit(s).
You can enter up to four antenna unit position data. Setting range: [RAS001] to
[RAS004]. Do not select [RAS005] to [RAS010].
Setup the antenna units activated here on the [Installation Parameters] menu. See
subsection 1.4.5 for details.
Note 1: Check all the antenna unit connected to the processor unit.
Note 2: For FAR-2xx7 and FAR-2xx8 series radar antennas, set the antenna no.
(Equipment ID), taking care not to duplicate the Equipment ID of a chart radar. For
how to set the antenna no., see the installation manual of the radar.
5. Enter the position data of antenna unit(s) in the boxes [X (m)], [Y (m)], and [Z (m)].
Note 1: The value of [Z (m)] is reflected in the default setting on [MENU]o[1
ECHO]o[1 CUSTOMIZE ECHO]o[9 CONDITION]o[1 STC ANT HEIGHT].
6. Enter the information for the GPS sensor, AIS transponder, echo sounder, and
SDME sensor in a similar manner.
Note: For the chart radar, [RAS001] (antenna unit), [GPS001] (GPS sensor),
[AIS001] (AIS transponder), and [LOG001] (SDME sensor) are activated by de-
fault. Enter their position data.
7. To save the configuration, perform a consistency check, then save the configura-
tion data on the [Save and Sync] menu.

1. INITIAL SETTING AND ADJUSTMENT
1-14
1.4 [Installation Parameters] Menu
The [Installation Parameters] menu sets the signals and input data of the sensors.
First, select the sensor data at the [Sensor Setting] window. Then select the sensor
from which the units (radar sensor (antenna unit), MFD, ECDIS, radar, chart radar,
and sensor adapter) obtain the sensor data.
1.4.1 Sensor setting
1. Access the [Common Installation Setting] menu and click [Installation Parame-
ters] on the tab bar.
2. Click [Sensor Setting] on the menu bar, then click [GPS Sensor].
3. Check applicable check boxes according to the number of GPS receivers con-
nected.
4. Set [SFID], [Data Type] and [Strict/Loose], referring to the table shown below.
5. Click the [Details] button to set the following items, referring to the following table.
Item Remarks
[SFID] Keep the default setting.
[Data Type] Sets the RX sentence data format.
Setting options: [IEC 61162-1 Ed3], [IEC 61162-1 Ed4], [ASCII], [BINA-
RY], [MODBUS], [PSU]. Do not select [ASCII] or [BINARY].
[Strict/
Loose]
Sets the presence or absence of sentence data.
[Strict]: Confirm the validity of checksum, then receive sentence.
[Loose]: Receive sentence regardless of checksum invalidity.
TCS
TCS
AMS
AMS
CCRS
CCRS
Own Ship Setting
Own Ship Setting
Basic Setting
Basic Setting
Installation Parameters
Installation Parameters
The time to timeout for receiving data. Keep the dafault setting.
For [Other Sensor]
For [VDR]
For other units