FUTABA R6303SBE User manual

Usage condition for conventional system output
(Ch1-3) on "High Speed mode"
󾾝CAUTION
󾾙The "High Speed mode" accept the digital servos only or
most type of peripherals.
•Ifananalogservoisconnectedtotheseoutputsitwillcausea
malfunction.Pleasechecktheperipheralsifthereisamalfunctionfull
stickmovement.Ifthereisamalfunctionchangethereceiverbackto
"Normal mode."
Applicable systems: FASST-2.4GHz 7ch or 8ch/10ch/Multi-ch system
R6303SBE
Compliance Information Statement
(for U.S.A.)
This device, trade name Futaba Corporation of America, model number R6303SBE,
complies with part15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesiredoperation.
The responsible party of this device compliance is:
Futaba Service Center
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.
TEL [phone] or E-mail: [email protected] (Support)
R6303SBE Specications
FASST-2.4GHz (7ch/8ch/10ch/Multi-ch) system/S.BUS port and 3 channels for
conventional system/high-speed receiver
• Size: 0.89 x 1.47 x 0.37 in. (22.5 x 37.4 x 9.3 mm)
• Weight: 0.22 oz. (6.3g)
• Power requirement: 3.7V to 7.4V(Voltage range: 3.5 to 8.4V)
* Be sure that when using ESC's regulated output the capacity of the ESC must meet your usage
condition.
*The Battery F/S voltage is set for 4-cell NiCd/NiMH battery. Battery F/S function doesn't
work properly when other type battery is used.
* The fail safe function can be set for each channel when on "Multi-ch" mode, however, it differs
according to the transmitter. When on "7ch" mode, the fail safe function can be set for 3-channel
only.
*S.BUS port: R6303SBE can be used up to 7 channels or less on the "7ch" mode and 16 channels
+ DG1/2 or less on the "8ch/10ch/Multi-ch" mode, however, it differs according to the transmitter.
Thank you for purchasing a Futaba R6303SBE FASST-2.4GHz receiver.
The R6303SBE has an S.BUS system output port and 3 conventional
system channel outputs. It can also be used with conventional system
servos, etc. in addition to S.BUS system compatible servos and gyros,
etc. When the linking procedure is performed, R6303SBE recognizes the
signal mode (FASST-2.4GHz 7ch mode or 8ch/10ch/Multi-ch mode)
automatically.
The R6303SBE can change the output CH from seven groups (CH group
table).
In addition, the operating mode (high-speed mode/normal mode) can be
selected.
󾾝WARNING
󾾛DonotperformtheLinkingprocedurewiththe
motorpoweredup.Thiscouldresultinserious
injury.
󾾙OncetheLinkingprocessiscompletedplease
cyclethepowertothereceivertomakesure
thatitislinkedandunderthecontrolofthetransmitter.
Link to the Transmitter
1PressandholdtheLink/Modebuttonbetween2and5
seconds.
Re-adjust the 3CH F/S position (only for TM-8)
1PressandholdtheLink/Modebuttonbetween1and2
seconds.
0 to 1 sec. 1 to 2 sec. 2 to 5 sec. More than 5 sec.
0 sec. 1 sec. 2 sec.
Press and Hold
No function
With TM-8
(not included in this set)
To set the F/S
position(No re-link)
Re-link(ID set) and to
set the F/S position
No function
Other than TM-8
(not included in this set)
Re-link(ID set)
CH change mode
CH change mode
5 sec.
Power Source Precautions
It is not recommended to use a power source of less then 4.0V.
However if less than 4.0V is used please keep in mind the conditions
below..
•The FailSafeFunctionMUSTbe set to"OFF"since itwilldisturb the
normal operation of the receiver.
•Please makesure that the fully loaded conditionontheESCand the
Servos will not disturb normal receiver operation before the start of
youright.
 This isVERY Important once the voltage drops below 3.5 volts the
receiverwillnolongercontinuetooperate.
•Please be sure that everything on continues to work correctly all the
waydownto3.5volts.ie:Servos,ESC...
The input voltage must not exceed the servo rating or 8.4V which ever
is lower.
Link/Mode button
LED
R6303SBE
•Port2(InitialsettingistheChannel2)
•Port1(InitialsettingistheChannel1)
•Channel3outputforconventionalsystem/Battery
terminal
•S.BUSPort
(Connectors)
1M23N17464
FASST-2.4GHz (7ch/8ch/10ch/Multi-ch) S.BUS port and 3 channels for
conventional system High-Speed receiver
for parkflight or indoor use airplanes / small size electric helicopters.
󾾝WARNING
󾾙If a part of the fuselage is made of conductive
materials such as metal and carbon, install
the receiver so that it is never covered with these
materials and the antenna never touch them.
• It becomes impossible to receive,it cases erratic operation or loss of
control.
󾾙Do not use it for a middle or large scale model.
•R6203SBEforparkight orindooruseairplanes and small size
electrichelicoptersupto1000mmofmainrotordiameter.
Thereisapossibilityofcrashingwhenusingitforthemiddleorlarge
scale model.

Operation Normal/High Speed Mode Select
The operation mode is set on "Normal mode" from the factory. To
change the mode please follow the steps below.
1Turnoffthereceiver.
2PressandholdtheLink/Modebuttonandturnonthereceiver.
Pressandhold the buttonformore then1second. TheLED
willstarttoashandwillindicatethecurrentstatus.
3Releasethebutton.
4Turnoffthereceiver.
By following these steps the receiver modes can be switched back and
forth between normal and high speed modes.
0 to 1 sec. More than 1 sec.
0 sec. 1 sec.
Press and Hold
Turn on the receiver.
No function
Showing the CURRENT
mode with blink.
Red Blink = Normal
Green/Red Blink =
High Speed
Solid as the mode changed.
Red Solid = Normal
Green/Red Solid = High
Speed
(Become Red after 1 second)
（Function）To change the mode between
Normal and High Speed
（LED
Status）
Please check the operation mode by observing the LED when turning on
the receiver. The best way to conrm the mode you are on is to make sure
that there are no other
FASST transmitters turned on around you.
When turning on the receiver, the LED will be;
•Redwhenon"Normalmode"
•GreenandRed(makingorange)whenon"HighSpeedmode". (After2
seconds,theLEDwillchangetored.)
If there are any FASST transmitters turned on around the receiver, the
LED may show the above status, but just for a brief moment and then
change to the status indicated in the "LED indication" table below.
FUTABA CORPORATION
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan
Phone: [phone], Facsimile: [phone]
©FUTABA CORPORATION 2012, 4 (1)
LED Indication
Green Red Status
Solid Solid Initializingwhenon"HighSpeedmode"
Off Solid No signal reception
Solid Off Receivingsignals
Blink Off ReceivingsignalsbutIDisunmatched
Alternate blink Unrecoverableerror(EEPROM,etc.)
CH group table
CH group LED blink Port 1 Port 2
group 1 Red １time CH1 CH2
group 2 Red ２time CH1 CH4
group 3 Red ３time CH2 CH4
group 4 Green １time CH1 CH5
group 5 Green 2time CH2 CH7
group 6 Green 3time CH4 CH8
group 7 Red/Green １time CH11 CH12
group 8 Red/Green 2time not used not used
group 9 Red/Green 3time not used not used
※Initial setting is group 1.
※The groups 8 and 9 are not usually used.
※3CH port and S.BUS port never change.
R6303SBE
[Example:ConnectingGYA431toGroup3]
CH4
Rudderservo
CH6
2ndAileronservo
CH2
Elevatorservo
Port1
Port2
S.BUS
3/B CH1
Aileronservo
Battery CH3
Throttleservo
（GYA431isusedfortheaileronofanairplane）
GYA431
HUB
When using the R6303SBE Receiver with
the GYA430, 431 and CGY750
The following table corresponds to the gyro's functions. A port can be
used effectively. The servo which a gyro controls is connected to a gyro.
* Please refer to the description of each gyro manual.
S.BUS gyro group table
Gyro control CHCH group
Rudder group 1
Elevator group 2
Aileron group 3
Elevator+Rudder group 4
Aileron+Rudder group 5
Aileron+Elevator group 6
Aileron+Elevator+Rudder
or CGY750 group 7
When S.BUS is used
* Set the channel of S.BUSservosbyusinganSBC-1channelchanger,CIU-2
USBserialinterfaceortheprogrammingsoftwareinthe18MZ transmitter.
* Can also be used together with conventional servos. However, conventional
servos cannot be used by the S.BUS output.
* When using servos with a remote battery pack, use S.BUS Hub with Cable
(2-way/remote battery pack use).
Please refer to the instruction manual of S.BUS Hub with Cable (2-way/re-
mote battery pack use) for the connection method.
*Turn on the power in transmitter→receiver order. In addition, always check
the operation of all the servos before ight.
*Do not insert or remove the servo connector while the receiver power is ON.
What is S.BUS?
S.BUS is different from conventional radio control systems in that it
uses data communication to transmit control signals from the receiver
to a servo, gyro, or other S.BUS compatible devices. The S.BUS
devices only execute only those comands for there own set channel.
This is why a single signal can be used to connect multiple servos.
How to Set the Operation Channel
It is possible to choose the operation channel mode of the port 1 and 2
from 7 setting groups.
1Turn onthe receiver.  (At this moment, the transmittershould
beoff.)Then, ensure theLED is lit inRED or ashinggreen
light.
2PressandholdtheLink/Modebuttonmorethan5seconds.
3Releasethebutton whentheLEDblinksREDandGREEN
simultaneously.
4Thereceiverisnowinthe "OperationCHSet" mode. At this
moment,theLEDindicatescurrentsetstatusthroughashing
apatternthatcorrespondstotheCHgroup.
*Cannot exit this CH setting mode before the operation mode is xed.
**See the below table that shows correspondence between "CH group" and way
of ashing LED.
***Default CH mode is "Group 1".
5Bypressing the Link/Modebutton,theoperationCHisswitched
sequentiallyas"group1""group2""group3"....
6Theoperation modewillbesetby pressingtheLink/Mode
buttonmorethan2secondsatthedesiredCHgroup.
7Releasethebutton whentheLEDblinksREDandGREEN
simultaneously.Afterreleasingthebutton,theREDand
GREENLEDarelit1secondsimultaneously.Then,the
operationCHisxed.
8 After conrming the operation CH mode is changed, turn off
andbackonthereceiverpower.
*The “Operation CH Set” mode cannot be changed during the receiver
communicates to the transmitter.