Gamber Johnson 7160-1082 Series User manual

Rev. A
INST-833
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
Product Mounting Disclaimer
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
Printing Spec:
This docking station is designed to be used with a variety of Gamber-Johnson mounting
Getac with the computer.
features, set-up, and operation of the computer, please refer to the manual provided by
This instruction sheet is for the Getac K120 Laptop docking station only. For instructions on
individual product.
INSTALLATION INSTRUCTIONS
systems. Installation instructions for other Gamber-Johnson products are provided with each
Product Revision Form
PS-001
7160-1082
GETAC K120 LAPTOP DOCKING STATION
This instruction sheet is for the following products:
Item No. 7160-1082-00 No RF (External Power Supply sold separately)
Item No. 7160-1082-03 Tri RF (External Power Supply sold separately)
Getac recommends using the following Power Adapters to power the docking station. They
can be ordered from Gamber-Johnson seperately.
17057 - Auto (12-32 Vdc input) - Available with the docking station as KIT 7170-0693
16079 - Isolated (12-32 Vdc input)
16078 - Isolated (20-60 Vdc input)
16513 - Isolated (72-110 Vdc input)
1 / 6
©
C
opyright 20
1
9
Gamber
-
Johnson, LLC

IMPORTANT SAFETY INFORMATION FOR INSTALLERS
Safety is dependent on the proper installation and servicing of this docking station. It is
important to read and follow all instructions before installing this product.
To properly install a Gamber-Johnson docking station you must have a good understanding of
automotive electrical procedures and systems, along with proficiency in the installation and
service of aftermarket vehicle equipment.
There are no adjustments required at any time of the electrical components within the docking
station. Opening the docking station will void the product warranty.
During Installation:
DO NOT connect this docking station to the vehicle battery until:
All other electrical connections are made1.
Mounting of all components is complete2.
Verification that no shorts exist in the entire system3.
DO NOT install equipment or route wires or cords in the deployment path of any air bag.
When drilling into the vehicle, DO make sure that both sides of the surface are clear of
anything that could be damaged.
CAUTION: If wiring is shorted to the frame, high current conductors can cause hazardous
sparks resulting in electrical fires or flying molten metal.
After installation:
Test the docking station to ensure that it is working properly.
File these instructions in a safe place and refer to them when performing maintenance or re-
installing.
WARNING: Failure to follow all safety precautions and instructions may result in property
damage, serious injury, or death.
PRE-INSTALLATION RECOMMENDATIONS
Conduct a "Bench Test"
Gamber-Johnson strongly advises a "bench test" be conducted to verify all electronic and
software issues are resolved prior to installation:
Make sure the computer is operational by itself.1. Insert computer into the docking station and verify that the computer is2.
operating in the dock.
Interconnect entire assembly and verify start-up of all components, including3. other equipment (printers, modems, scanners, etc.)
Gamber-Johnson recommends positioning of all mounts and equipment in the vehicle
prior to the actual install to verify that mounting locations are safe and practical.
2 / 6

Part#/Serial# Label
Port Indentification
(Ports, see page 4)
External Antenna - SMA
(WiFi, GPS, CELL)
(Optional)
VESA 75mm Hole Pattern
1/4-20 x 0.500" hardware provided
Release Button
(User Interface)
Port Blocker
Power - Laptop
Port Blocker
USB - Laptop
Screen Support
Mount Location
Barrel Key Lock
Latching Indicator
External Antenna - Tri RF
(Optional)
Center Wall
Rear Wall
Docking Connector
Rear Hooks
Front Guide Pins
Tablet Lock Fin
Shock Absorbers
(2) USB 2.0
(Fast Charging)
1500 mA
Contact Friendly Edges
FEATURE IDENTIFICATION
Provides docking guidance
and connector protection,
prevents mis-docking
3 / 6

Cables route past mounting equipment
PORT IDENTIFICATION
Serial
Ethernet (2)
(RJ45)
USB3.0
(Fast Charging)
1500 mA
USB3.0 (2)
900 mA USB2.0
500 mA
VGAHDMI
Power Input: 19 Vdc
CABLE MANAGMENT FEATURES AND PROPER INSTALLATION
1.) Use Zip ties (provided) to secure each port cable to the specific strain relief feature on the dock
2.) Use Zip ties (provided) to secure bundled cables for improved routing - OPTIONAL
4 / 6
1.) Cable Tie Slots
(Port Specific)
Power
Ethernet
Ethernet
USB (2)
USB (2)
HDMI
2.) Cable Tie Slots (2)
(Extra)

DOCKING AND UNDOCKING THE COMPUTER
OPERATION - DOCKING
1. Insert the front of the laptop
into the front guide pines of the
dock. The walls on the dock will
guide the tablet into place.
2. Rotate the back of the laptop
and push down, overcoming the
resistance until an audible click is
heard. The Latching Indicator will
also slide inside the dock,
signaling the "Latched" position.
3. Optional - With the dock in the
"Latched" position, turn the lock
to the "LOCKED" position (CW).
This will lock the laptop in the
dock, and secure the tablet if the
screen is closed and latched.
OPERATION - UNDOCKING
1. Turn the lock to the
"UNLOCKED" position (CCW).
The blue Tablet Lock Fin will
spring back down into the dock.
2. With your hand at the right
corner of the laptop, pull up on
the blue Release Button until the
springs release the laptop.
3. Remove the laptop by pulling
it away from the dock. This can
be done with the same hand.
5 / 6
Insert Front First
Push Down
Tablet Lock Fin
pops up after locking
"Un-Latched" Position
"Un-Locked" Position
"Latched" Position
"Locked" Position
Pull Up
Pull Away

Gamber-Johnson LLC, 3001 Borham Ave.,
Stevens Point, WI, 54481, USA, 715-344-3482
Regulatory Certification Information
Regulatory Model #: 7160-1082
GJ Model #'s & Description:
7160-1082-00 Dock-Getac K120 Laptop-No RF
7160-1082-03 Dock-Getac K120 Laptop-Tri RF
Certifications:
EN 55032: 2012/AC: 2013 Class B•
EN 50498: 2010•
E-mark•
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions. (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
6 / 6