Gamber Johnson GETAC V110 User manual

Rev.D INST-625
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
7160-0515
mounting systems. Installation instructions for other Gamber-Johnson products
Form
This docking station is designed to be used with a variety of Gamber-Johnson
INSTALLATION INSTRUCTIONS
are provided with each individual product.
Revision
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
Printing Spec:
PS-001
Product
GETAC V110 DOCKING STATION
This instruction sheet is for the V110 docking station only. For instructions on
features, set-up, and operation of the V110 computer, please refer to the manual
provided by Getac with the computer.
This instruction sheet is for the following products:
Item No. 7160-0515-00 Dock - Getac - V110 - No RF
Item No. 7160-0515-03 Dock - Getac - V110 - Tri-RF
1/5
© Copyright 2014 Gamber-Johnson, LLC

IMPORTANT SAFETY INFORMATION FOR INSTALLERS
Safety is dependent on the proper installation and servicing of this docking station. It is
important to read and follow all instructions before installing this product.
To properly install a Gamber-Johnson docking station you must have a good
understanding of automotive electrical procedures and systems, along with proficiency
in the installation and service of aftermarket vehicle equipment.
There are no adjustments required at any time of the electrical components within the
docking station. Opening the docking station will void the product warranty.
During Installation:
DO NOT connect this docking station to the vehicle battery until:
All other electrical connections are made1. Mounting of all components is complete2. Verification that no shorts exist in the entire system3.
DO NOT install equipment or route wiring or cords in the deployment path of any air bag.
When drilling into the vehicle, DO make sure that both sides of the surface are clear of
anything that could be damaged.
CAUTION: If wiring is shorted to the frame, high current conductors can cause hazardous
sparks resulting in electrical fires or flying molten metal.
After installation:
Test the docking station to ensure that it is working properly.
File these instructions in a safe place and refer to them when performing maintenance or re-
installing.
WARNING: Failure to follow all safety precautions and instructions may result in property
damage, serious injury, or death.
PRE-INSTALLATION RECOMMENDATIONS
Conduct a "Bench Test"
Gamber-Johnson strongly advises a "bench test" be conducted to verify all
electronic and software issues are resolved prior to installation:
Make sure the computer is operational by itself.1. Insert computer into the docking station and verify that the computer is2. operating in the dock.
Interconnect entire assembly and verify start-up of all components,3. including other equipment (printers, modems, scanners, etc.)
Gamber-Johnson recommends positioning of all mounts and equipment in the
vehicle prior to the actual install to verify that mounting locations are safe and
practical.
2/5

Screen Support
Lock Button
Latch
Tri-RF Connector
Rear Hooks
Docking Connector
Front Hooks
Stylus Holder
Deck
Bumpers
Guide Blocks
4X 1/4-20unc x .62"
mounting studs
(2) Serial ports
GPS
WLAN
WWAN
Microphone
Headphone
VGA Port
HDMI Port Strain Relief Bracket
(1) USB 3.0 port
19VDC Input port
Network (RJ-45)
(3) USB 2.0 ports
2X 6-32unc inserts-
Screen Support
mounting position
V110 DOCKING STATION FEATURE IDENTIFICATON
3/5

DOCKING AND UNDOCKING THE COMPUTER
DOCKING THE COMPUTER
1. Turn the computer off.
2. Un-latch the dock, making sure the
rear hooks move backward (Figure 1).
3. With the computer held at an
angle, place the two notches on the
front edge of the computer into the
front hooks. (Figure 2)
4. Lower the computer down on to
the dock.
5. While pushing the computer down,
to compress the docking connector,
close the latch to engage the rear
hooks into the notches on the back
edge of the computer. (Figure 3)
6. Lock the latch, if required, for
security.
7. Adjust the position of the screen
support. (Figure 4)
UNDOCKING THE COMPUTER
1. Turn the computer off. Move screen
support back, close display.
2. Unlock latch, if locked.
3. Press the Lock Button on the latch.
The latch will spring open and the rear
hooks will disengage from the computer
case.
4. Lift computer up off dock, back
edge first.
Figure 2
Figure 3
Figure 4
Figure 1
4/5

10R-04 7267
8
E
Gamber-Johnson LLC, 3001 Borham Ave.,
Stevens Point, WI, 54481, USA, 715-344-3482
Regulatory Certification Information
Regulatory Model #: 7160-0515
GJ Model #'s & Description:
7160-0515-00 Dock - Getac - V110 - No RF
7160-0515-03 Dock - Getac - V110 - Tri-RF
Certifications:
EN 55022:2010 CISPR 22:2008 Class B•EN 50498:2010•EN 50581:2012•E-Mark•-• -• -• -•
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions. (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interfernece that may cause undesired operation.
5/5