Gantner GAT ECO.Side Lock 7000 BA Guide

www.gantner.com HB_GAT-GAT-ECOSide-Lock7000-BA--EN_14
1
GAT ECO.Side Lock 7000 BA / NW BA
Battery-Powered Multi-Technology Electronic Lock
Installation, Commissioning, Operation
Document Version 1.4

GAT ECO.Side Lock 7000 BA / NW BA
2 HB_GAT-GAT-ECOSide-Lock7000-BA--EN_14 www.gantner.com
©
Copyright 2018 by GANTNER Electronic GmbH, Schruns (Austria).
Operating instructions, manuals and software are protected by copyright. All rights are reserved. Copying, duplication, translation,
installation in any electronic medium or machine-readable form in whole or in part is prohibited. The sole exception is represented
by creation of a back-up copy of software for own use as a safeguard, so far as this is technically possible and recommended by
us. Any infringement will render the party committing such infringement liable to compensation payment.
Liability
Any claims against the manufacturer based on the hardware or software products described in this manual shall depend
exclusively on the conditions of the guarantee. Any further-reaching claims are excluded, and in particular the manufacturer
accepts no liability for the completeness or accuracy of the contents of this manual. The right is reserved to make alterations, and
alterations may be made at any time without prior notice being given.
Trademarks
Attention is drawn at this point to markings and registered trademarks used in this manual. All product and company names, which
are mentioned in this manual, are only used for identification and explanation purposes. Some of these names may be trademarks
or registered trademarks of the corresponding company.
Contact
For general inquiries of further information on the GAT ECO.Side Lock 7000 BA and GAT ECO.Side Lock 7000 NW BA, see the
contact information below.
Contact address of manufacturer:
GANTNER Electronic GmbH
Montafonerstrasse 8
6780 Schruns, Austria
Phone: [phone] - 0
Fax: [phone] - 8000

GAT ECO.Side Lock 7000 BA / NW BA
www.gantner.com HB_GAT-GAT-ECOSide-Lock7000-BA--EN_14 3
Important Information
Dear Customer,
Our aim is to ensure that our product operates with safety and to your complete satisfaction. To achieve this aim, please take
this opportunity to familiarize yourself with the following guidelines.
- Pay attention to the safety messages in this manual. The messages are indicated by the signal words "DANGER",
"WARNING", or "CAUTION", and inform you about hazardous situations and how to avoid them.
- Pay attention to messages indicated by the "NOTICE" signal word. These messages include important information for
avoiding property damage.
- Pay attention to the symbols and safety messages on the product.
- Read all instructions in this manual carefully before installing or operating the product.
- Where not otherwise specifically documented, the appropriate installation, commissioning, operation and maintenance
of the product is the customer’s responsibility.
- Keep this manual in a safe place for quick reference.
Notation of Safety Information and Safety Symbols
This manual includes important safety messages and symbols intended to inform the user about potentially hazardous situations
or important information for the safe and proper use of the described product(s). The safety messages also include directives on
how to avoid hazardous situations. These safety messages and directives must be read and observed.
The structure of the safety messages and the meaning of the symbols used in this manual are described in this section.
1. Safety Messages for Personal Injury
Personal safety messages contain a signal word, describe the nature of the hazard, and indicate how to avoid the hazard.
The safety alert symbol used without a signal word always precedes important safety information that must be read
carefully and the instructions carefully observed. Not doing so may cause personal injury.
Format of safety messages that apply to an entire section:
These safety messages may be used with or without a symbol.
Electrical shock
➔Touching current-conducting parts may result in injury due to electrical shock.
- Do not remove safety protection and covers.
- Do not touch the electrical connections while power is being supplied.
Format of safety messages that are embedded in text and apply to a specific point:
CAUTION! Electrical shock. Never remove safety protection and covers. Do not touch the electrical connections while
power is being supplied.

GAT ECO.Side Lock 7000 BA / NW BA
4 HB_GAT-GAT-ECOSide-Lock7000-BA--EN_14 www.gantner.com
2. Property Damage Messages
Property damage messages are used to describe potentially hazardous situations that may lead to property damage. These
messages have the same layout as safety messages but use the signal word "NOTICE" instead of “CAUTION”.
Format of property damage messages that apply to an entire section:
Risk of damage to the device and connected devices
Risk of malfunction
- Read the following instructions carefully before installing the device.
- Always adhere to the instructions.
Format of property damage messages that are embedded in text and apply to a specific
point:
NOTE! Risk of damage to the device and connected devices. Read the following instructions carefully before installing the
device.
3. Definition of the Signal Words
Indicates a hazardous situation that, if not avoided, may result in minor or moderate injury.
Indicates information considered important, but not hazard-related (e.g., messages relating to
property damage).
4. Definition of the Safety Symbols
Caution: General Information
This symbol indicates general warnings or cautions that are not related to a particular type of hazard.
Caution: Electrical Shock
This symbol indicates warnings related to electrical hazards (danger due to high voltage).
Prohibited: Do Not Disassemble
This symbol indicates warnings about not disassembling certain components or equipment. Disassembling may
lead to damage or malfunction of the device.
Mandatory Action: General Information
This symbol indicates general information that must be read and followed before proceeding with the
accompanying instructions.
Mandatory Action: Read Instructions
This symbol indicates information referring to an important description in the manual, or other documentation,
which must be read and followed.

GAT ECO.Side Lock 7000 BA / NW BA
www.gantner.com HB_GAT-GAT-ECOSide-Lock7000-BA--EN_14 5
Important Safety Information
−The installation, commissioning, and servicing of our products must be performed only by suitably trained
personnel. In particular, electrical connections must only be made by correspondingly qualified specialists.
Always observe the relevant installation regulations in accordance with the national Electrical Engineers
Association.
➔Unqualified personnel may potentially perform actions that result in injury due to electrical shock.
−Where not otherwise stated, installation and maintenance work on our products must be carried out when
disconnected from the power supply. This applies in particular to appliances that are normally supplied by
low-voltage current.
➔If the appliance is not disconnected from power, touching terminals or other internal parts of the
appliance may lead to injury due to electrical shock.
−It is prohibited to alter the products (devices, cabling, etc.).
➔Alterations to the products may subsequently result in personal injury, property damage, or damage to
the products.
−Do not remove protective shields and covers.
➔Removing protective shields and covers may result in personal injury or property damage.
−Do not attempt to repair a product after a defect, failure, or damage is detected. In addition, do not put the
product back into operation. In such cases, it is essential to contact your GANTNER representative or the
GANTNER support hotline.
−The installation, commissioning, operation, and maintenance of the product must be carried out in
accordance with the technical conditions of operation as described in the corresponding documentation.
Therefore, it is essential to read the corresponding chapter of this manual and observe the instructions and
information therein.
−If there are still some points that are not entirely clear, please do not take a chance. All queries can be
clarified by your GANTNER representative or by ringing the GANTNER support hotline.
−Directly on receipt of the goods, inspect both the packaging and the product itself for any signs of damage.
Also check that the delivery is complete and includes all accessories, documentation, auxiliary devices,
etc.
−If the packaging or product has been damaged in transport, or should you suspect that it may have a fault,
the product must not be put into service. Contact your GANTNER representative who will endeavor to
resolve the problem as quickly as possible.
−GANTNER Electronic GmbH accepts no responsibility for any injuries or damage caused as a result of
improper use.
Although great care is taken, and we are continuously aiming for improvement, we cannot completely exclude the possibility of
errors appearing in our documentation. GANTNER Electronic GmbH therefore accepts no responsibility for the completeness or
the accuracy of this manual. The right is reserved to make alterations at any time without prior notice.
Should you discover any fault with the product or in its accompanying documentation, or you have any suggestions for
improvement, you may confidently inform your GANTNER representative or GANTNER Electronic GmbH directly.
We especially look forward to hearing from you if you want to let us know that everything is functioning perfectly.

GAT ECO.Side Lock 7000 BA / NW BA
6 HB_GAT-GAT-ECOSide-Lock7000-BA--EN_14 www.gantner.com
The GAT ECO.Side Lock 7000 BA / NW BA was developed and fabricated under the quality management standard ISO 9001 and
GANTNER Electronic GmbH is also certified according to standard ISO 14001.
This product is in conformity with the following EC directives, including all applicable amendments:
- 2014/53/EU (Radio Equipment Directive)
The complete text of the CE Declaration of Conformity is available on the following internet link:
http://www.gantner.com/en/downloads-gat-eco-sidelock7xxx_90lweb4f22
GANTNER is committed to meeting or exceeding the requirements of the RoHS directive (2011/65/EU). The RoHS
directive requires that manufacturers eliminate or minimize the use of lead, mercury, hexavalent chromium,
cadmium, polybrominated biphenyls and polybrominated diphenyl ethers in electrical and electronic equipment sold
in the EU after July 1, 2006.
The WEEE symbol on GANTNER products and their packaging indicates that the corresponding material must not
be disposed of with normal household waste. Instead such marked waste equipment must be disposed of by
handing it over to a designated electronic waste recycling facility. Separating and recycling this waste equipment at
the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects
human health and the environment. Please contact your local authority for further details of your nearest electronic
waste recycling facility.
FCC INFORMATION (U.S.A.)
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that of which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Warning Statement:
[Any] changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
Compliance Information Statement:
INDUSTRY CANADA INFORMATION (IC ID: 11873A-1180067A)
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes :
1) l’appareil ne doit pas produire de brouillage;
2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
onctionnement.
ICES Statement (Canada)
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la class B est conforme à la norme NMB-003 du Canada.
FCC ID: NC4-GEA1180067A
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)This
device must not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.

GAT ECO.Side Lock 7000 BA / NW BA
Table of Contents
www.gantner.com HB_GAT-GAT-ECOSide-Lock7000-BA--EN_14 7
TABLE OF CONTENTS
1INTRODUCTION..............................................................................................................9
1.1 About this Manual.....................................................................................................................................9
1.2 Chapter Overview.....................................................................................................................................9
1.3 Contact & Inquiries ...................................................................................................................................9
1.4 Target Group...........................................................................................................................................10
1.5 Formatting...............................................................................................................................................10
Safety-Critical Information....................................................................................................................10
Non-Safety-Critical Information............................................................................................................10
Instructions and Results.......................................................................................................................10
2GENERAL INFORMATION ...........................................................................................11
2.1 Intended Use...........................................................................................................................................11
2.2 Functional Description ............................................................................................................................11
2.3 Terminology............................................................................................................................................12
2.4RFID Technology....................................................................................................................................13
2.5 System Components ..............................................................................................................................14
3INSTALLATION.............................................................................................................17
3.1 Target Group...........................................................................................................................................17
3.2 Definition of the Door Hinge (Right of Left Door)....................................................................................17
3.3 Test Installation.......................................................................................................................................18
3.4 Metallic and Non-Metallic Doors.............................................................................................................18
3.5 Bolt Gauge..............................................................................................................................................18
3.6 Door Status Contact ...............................................................................................................................19
3.7 Transportation Guidelines.......................................................................................................................19
3.8 Replacement after a Burglary Attempt ...................................................................................................19
3.9 Measurement Diagrams for Installation..................................................................................................20
Door Width ...........................................................................................................................................20
Dimensions of the GAT ECO.Side Lock 7000 BA and GAT NET.Lock Bolt Sets ...............................20
3.10 Installation in Lockers with Non-Metallic Doors (Except Glass) .............................................................22
Installation Requirements for the GAT ECO.Side Lock 7000 BA and Non-Metallic Doors .................23
Installation Instructions for the GAT ECO.Side Lock 7000 BA and Non-Metallic Doors .....................24
3.11 Installation in Lockers with Metallic Doors..............................................................................................25
Cutouts in the Locker Door ..................................................................................................................26
Installation Requirements for the GAT ECO.Side Lock 7000 BA and Metallic Doors .........................27
Installation Instructions for the GAT ECO.Side Lock 7000 BA and Metallic Doors .............................28
3.12 Installation in Lockers with Glass Doors.................................................................................................29
Installation Requirements for the GAT ECO.Side Lock 7000 BA and Glass Doors ............................30
Installation Instructions for the GAT ECO.Side Lock 7000 BA and Glass Doors ................................31
4COMMISSIONING .........................................................................................................33
4.1 Target Group...........................................................................................................................................33
4.2 Power Supply..........................................................................................................................................33
Battery Information...............................................................................................................................33
Inserting the Battery.............................................................................................................................33
Replacing the Battery...........................................................................................................................34
4.3 USB Connection .....................................................................................................................................35
4.4 Automatic Antenna Adjustment ..............................................................................................................37
Antenna Adjustment using the Service Data Carrier ...........................................................................37
Antenna Adjustment via GAT Config Manager....................................................................................37

GAT ECO.Side Lock 7000 BA / NW BA
Table of Contents
8 HB_GAT-GAT-ECOSide-Lock7000-BA--EN_14 www.gantner.com
5CONFIGURATION.........................................................................................................39
5.1 General Information ............................................................................................................................... 39
5.2 Setup for Configuration in GAT Config Manager................................................................................... 39
5.3 View and Edit the GAT ECO.Side Lock 7000 BA Configuration Settings ............................................. 41
5.4 Upload Configuration Settings to the GAT ECO.Side Lock 7000 BA.................................................... 42
5.5 Updating the GAT ECO.Side Lock 7000 BA Firmware.......................................................................... 43
5.6 Configuration Settings of the GAT ECO.Side Lock 7000 BA ................................................................ 44
Operating Mode................................................................................................................................... 44
Locker Number.................................................................................................................................... 44
Sound Signals ..................................................................................................................................... 44
Alarm Mode......................................................................................................................................... 44
Auto-Unlock......................................................................................................................................... 45
Duration of Use.................................................................................................................................... 45
Locking of Personal Locker without data carrier ................................................................................. 45
MASTER Data Carriers....................................................................................................................... 45
Configuration Settings Table............................................................................................................... 46
6OPERATION .................................................................................................................49
6.1 General .................................................................................................................................................. 49
6.2 Target Group.......................................................................................................................................... 49
6.3 Operating Modes.................................................................................................................................... 49
Free Locker Mode (with or without Duration of Use Function)............................................................ 50
Free Locker Universal Mode............................................................................................................... 51
Free Locker Unique Number Mode..................................................................................................... 52
Personal Locker Programming Card Mode......................................................................................... 52
Personal Locker Expiry Date Mode..................................................................................................... 53
6.4 GAT ECO.Basic Set B BA ..................................................................................................................... 55
6.5 Summary of System Data Carriers........................................................................................................ 55
MASTER Data Carrier......................................................................................................................... 55
OPEN MASTER Data Carrier.............................................................................................................. 56
DELETE MASTER Data Carrier.......................................................................................................... 56
PROGRAM Data Carrier..................................................................................................................... 56
BATTERY Data Carrier....................................................................................................................... 57
SERVICE Data Carrier........................................................................................................................ 57
6.6 Alarm and Handling ............................................................................................................................... 57
6.7 Signalization Overview........................................................................................................................... 58
7CLEANING AND MAINTENANCE................................................................................59
7.1 Target Group.......................................................................................................................................... 59
7.2 Functional Testing.................................................................................................................................. 59
7.3 Cleaning................................................................................................................................................. 60
7.4 Maintenance........................................................................................................................................... 60
8TECHNICAL DATA.......................................................................................................61
8.1 Power Supply......................................................................................................................................... 61
8.2 Reading Field......................................................................................................................................... 61
8.3 Memory and Time Management............................................................................................................ 61
8.4 Control and Display Elements................................................................................................................ 62
8.5 Interfaces ............................................................................................................................................... 62
8.6 Housing.................................................................................................................................................. 62
8.7 Environmental Conditions...................................................................................................................... 62

GAT ECO.Side Lock 7000 BA / NW BA
Introduction
www.gantner.com HB_GAT-GAT-ECOSide-Lock7000-BA--EN_14 9
1 INTRODUCTION
1.1 About this Manual
This manual provides information on the functionality of the GAT ECO.Side Lock 7000 BA and GAT ECO.Side Lock
7000 NW BA and includes an overview of how to configure the locks using GANTNER’s configuration software,
“GAT Config Manager”. There is a separate manual available for GAT Config Manager that explains all functions
associated with the software in greater detail.
The name “GAT ECO.Side Lock 7000 BA” is henceforth used in this manual to refer to both the GAT
ECO.Side Lock 7000 BA and the GAT ECO.Side Lock 7000 NW BA. Functionality that is specific to one type
of lock will be noted.
1.2 Chapter Overview
In chapter “2 GENERAL INFORMATION”, a functional description of the GAT ECO.Side Lock 7000 BA, the RFID
technologies supported by the device, key terms used in this manual and a summary of system components can be
found.
Chapter “3 INSTALLATION” contains the measurement diagrams and information required to install the GAT
ECO.Side Lock 7000 BA into lockers with metallic, non-metallic, and glass doors.
Chapter “4 COMMISSIONING” describes how to put the GAT ECO.Side Lock 7000 BA into operation and includes
information on the battery and USB connection.
Chapter “5 CONFIGURATION” describes how to configure the GAT ECO.Side Lock 7000 BA using GAT Config
Manager. The main configuration settings for the lock are explained and a table listing every setting is provided in
this chapter.
Chapter “6 OPERATION” describes the different operating modes of the GAT ECO.Side Lock 7000 BA. The system
data carriers required to maintain the locker system and the alarm function are also explained in this section.
Contained in chapter “7 CLEANING AND MAINTENANCE” are the instructions for performing functional testing and
cleaning of the GAT ECO.Side Lock 7000 BA to ensure that the correct operation is maintained.
Chapter “8 TECHNICAL DATA” contains all the relevant technical information for the GAT ECO.Side Lock 7000 BA.
1.3 Contact & Inquiries
If you have any questions concerning the GAT ECO.Side Lock 7000 BA / NW BA, please contact your local sales
partner or directly with one of the GANTNER branch offices. The contact details of the branch offices are provided
on the cover of this manual.

GAT ECO.Side Lock 7000 BA / NW BA
Introduction
10 HB_GAT-GAT-ECOSide-Lock7000-BA--EN_14 www.gantner.com
1.4 Target Group
This manual contains information relevant for the different stages in the operating life of the GAT ECO.Side Lock 7000
BA / NW BA. Information about the installation, commissioning, and service/maintenance of the GAT ECO.Side Lock
7000 BA / NW BA is separated into corresponding chapters. When a chapter is intended for a specific audience, this
is clarified at the beginning of the chapter.
Information for the following target groups is available in this manual:
- Installation technicians (installation, operation, configuration).
- Service technicians and cleaning personnel (service and maintenance).
- End users of the GAT ECO.Side Lock 7000 BA / NW BA (user manual).
Where not explicitly stated, the information in this manual is intended for all target groups in general.
CAUTION! Injury and property/equipment damage. The tasks described in each chapter must only be
performed by the specified target group. Unqualified personnel who perform the described tasks risk personal injury
or damaging property/equipment.
1.5 Formatting
Safety-Critical Information
The following formatting (with example text) is used in this manual to display important, safety-critical information
that must be read and followed.
NOTE! Following on from this signal word in the manual is a reference text that must be read and followed. The
reference text contains important information. Non-observance can lead to damage of the device or associated
equipment.
Non-Safety-Critical Information
The following formatting (with example text) is used in this manual to display important, but not safety-critical
information.
The text accompanying this symbol contains interesting information relevant to the current chapter. You do not
necessarily need to read this text; however, it will help you better understand the information in this section or
provide interesting tips for the described device or the operation of the software.
Instructions and Results
Instructions, which must be completed by the reader, and the results of these instructions are formatted as follows.
►This symbol represents an action or instruction that that must be followed.
oThis symbol represents the result after completing the previous instruction.

GAT ECO.Side Lock 7000 BA / NW BA
General Information
www.gantner.com HB_GAT-GAT-ECOSide-Lock7000-BA--EN_14 11
2 GENERAL INFORMATION
2.1 Intended Use
The GAT ECO.Side Lock 7000 BA is intended for the electronic locking of wardrobe lockers in facilities such as
fitness clubs, baths, golf resorts, hotels, and other individual company applications. The GAT ECO.Side Lock 7000
BA is locked / unlocked using contactless RFID (Radio Frequency Identification) data carriers.
2.2 Functional Description
The GAT ECO.Side Lock 7000 BA is suitable for any type of locker material (e.g., sheet metal, wood, HPL, solid
plastic, glass) and can be used for left- and right-hinged doors alike. Due to the mechanical compatibility with the
GAT NET.Lock 7000 series a quick and simple installation of existing locker rooms using the GAT ECO.Side Lock
7000 BA is possible.
The GAT ECO.Side Lock 7000 BA is installed on the inner side of the locker body. A bolt set is mounted on the
inside of the locker door. The bolt set holds the door shackle which inserts into the GAT ECO.Side Lock 7000 BA
and locks the door. The GAT NET.Lock BoltSet 7100 is designed for use with locker doors made from wood, HPL,
and solid plastic. For locker doors made from metal, use the GAT NET.Lock BoltSet 7200 and for glass locker
doors, the GAT NET.Lock BoltSet 7300 is available. The bolt sets include a passive booster used to amplify the
RFID reading field.
The GAT ECO.Side Lock 7000 BA is powered by one 3.6 V AA battery, which provides an operating life of up to 10
years* (at room temperature) before requiring replacement. The configuration (e.g., operating mode) of the GAT
ECO.Side Lock 7000 BA can be done on site via USB interface and GAT Config Manager configuration software or
using the programming data carrier. For the GAT ECO.Side Lock 7000 NW BA, communication via the integrated
wireless interface is also possible.
Using a locker
The user closes the door of their locker and while holding the door shut, holds their data carrier next to the RFID
reading field on the locker door (the reading field is indicated by an LED inside the lock). The GAT ECO.Side Lock
7000 BA reads the data carrier information and determines if the user is allowed to use the locker (depending on
their authorization status). If the user is authorized to use the locker, the GAT ECO.Side Lock 7000 BA locks the
locker door.
To unlock a previously locked locker, the user presses the locker door while holding their data carrier next to the
RFID reading field. The GAT ECO.Side Lock 7000 BA checks that the data carrier has valid authorization before
automatically unlocking the locker door.
* Different operating modes or configurations can reduce the battery lifetime.

GAT ECO.Side Lock 7000 BA / NW BA
General Information
12 HB_GAT-GAT-ECOSide-Lock7000-BA--EN_14 www.gantner.com
2.3 Terminology
Several key terms that are used often in this manual are defined below.
Computer / PC
These terms refer to all desktop and laptop computers running a MicrosoftWindows®operating system.
Data Carrier
A data carrier is a form of identification media that is used by staff and visitors in a facility for identification. Data
carriers are available in a variety of different forms such as plastic wristbands and chip cards. Data carriers are also
available to suit different RFID technologies, e.g., LEGIC, MIFARE®, ISO 15693.
System Data Carrier
Several different types of System Data Carriers are used for programming, service and maintenance tasks. These
data carriers have special functionalities and because they are essential for operation of the GAT ECO.Side Lock
7000 BA and they have security-related features, they must be kept in a secure place and be protected against
unauthorized use. Most of the System Data Carriers are included in the GAT ECO.Basic Set B BA. Some can be
ordered separately if needed.
FID (Company ID) and Site Key
The FID and site key are unique numbers assigned to every facility installation. The site key is a combination of the
FID and the read and write keys. The site key is used in MIFARE® and ISO 15693 systems and is encoded in every
data carrier and device used in the facility thereby ensuring that data carriers from one installation cannot be used in
other installations.
GAT Config Manager
GANTNER developed PC software that is used to configure GANTNER devices such as the GAT ECO.Side Lock
7000 BA. A separate manual is available and integrated into the software. While the software is open, click on the
“Help” drop-down menu and select “How Do I”.
Lock
General term for the GAT ECO.Side Lock 7000 BA.
Locker
The term "locker" is used to describe all possible locker applications that can be fitted with a GANTNER electronic
lock. Typical applications include a changing room locker, a deposit box, or a private box.
RFID (Radio-Frequency Identification)
Identification over a short distance using radio frequency. An RFID data carrier is used to identify users in
GANTNER systems.
User / Guest / Visitor
These general terms refer to the people in a facility who use the locker system, i.e., the GAT ECO.Side Lock 7000
BA, data carriers, and other GANTNER devices.

GAT ECO.Side Lock 7000 BA / NW BA
General Information
www.gantner.com HB_GAT-GAT-ECOSide-Lock7000-BA--EN_14 13
2.4 RFID Technology
Identification of users by GANTNER devices within a facility is achieved via RFID (radio-frequency identification)
technology using a frequency of 13.56 MHz. There are various RFID technologies available with different letters
added to the GANTNER model name to notify of the technology the device supports:
- "B": LEGIC
- "F": MIFARE®
- "ISO": ISO 15693
- “ICLS”: HID iCLASS®
The GAT ECO.Side Lock 7000 BA has a multi-technology RFID reader (LEGIC advant) that allows it to operate with
a range of RFID technologies. The information in this manual is applicable for the following technologies that can be
used with the GAT ECO.Side Lock 7000 BA.
UID and Segments
- LEGIC prime
- LEGIC advant
UID
- ISO 15693
- ISO 14443 (MIFARE)
- Classic (1k and 4k)
- Ultralight®
- DESFire EV1®and EV2®
- HID iCLASS (13.56 MHz)
In addition to the different RFID technologies, data carriers are available in a variety of shapes and sizes. The GAT
ECO.Side Lock 7000 BA is designed to operate with all different types of data carrier media.

GAT ECO.Side Lock 7000 BA / NW BA
General Information
14 HB_GAT-GAT-ECOSide-Lock7000-BA--EN_14 www.gantner.com
2.5 System Components
The GAT ECO.Side Lock 7000 BA system consists of the following system parts.
Figure 2.1 –Components of the GAT ECO.Side Lock 7000 system
1. GAT ECO.Side Lock 7000 BA / NW BA
2. GATNET.LockBoltSet7100
3. GAT NET.Lock BoltSet 7200
5. GAT NET.Lock Tool 7000
6. GAT NET.Lock Label GEA xxx
(Door labels in different designs)
For lockers with glass doors
For lockers with non-metallic
doors
4. GAT NET.Lock BoltSet 7300
8. GAT ECO.Basic Set B BA
For lockers with metallic doors
7. Battery
Tadiran SL-860/S (EU)
Tadiran TL-4903/S (US)
9. GAT Key Tag BA Open Master

GAT ECO.Side Lock 7000 BA / NW BA
General Information
www.gantner.com HB_GAT-GAT-ECOSide-Lock7000-BA--EN_14 15
1. GAT ECO.Side Lock 7000 BA (Part No. 583125)
Battery-powered locker lock with multi-technology RFID reader. Without batteries, without bolt set, and without
door label.
GAT ECO.Side Lock 7000 NW BA (Part No. 800925)
Battery-powered locker lock with multi-technology RFID reader and wireless interface. Without batteries,
without bolt set, and without door label.
2. GAT NET.Lock BoltSet 7100 (Part No. 369535)
Bolt set with door shackle and booster. Used for non-metallic doors. The bolt set is mounted on the inside of
the locker door.
3. GAT NET.Lock BoltSet 7200 (Part No. 532123)
Bolt set with door shackle and booster. Used for metallic doors. The bolt set is installed into locker door. The
label carrier is included in the set.
4. GAT NET.Lock BoltSet 7300 (Part No. 774232)
Bolt set with door shackle, booster, and metal support. Used for glass doors. The bolt set with metal support
attached are glued on the inner side of the glass door. Adhesive is not included with the set.
5. GAT NET.Lock Tool 7000 (Part No. 533831)
Centre punch gauge for bolt mounting on the locker door. By using the gauge drill holes for the bolt set
installation can be accurately marked on the locker door.
6. GAT NET.Lock Label 7000 GEA xxx
Self-adhesive locker door labels in GANTNER design. For metallic doors, the label is stuck onto the label
carrier. For non-metallic doors, the label is stuck directly onto the door. The labels are available for right and left
doors and with or without printed locker numbers:
- GAT NET.Lock Label GEA right (Part No. 679034)
For right-hinged doors, without numbering
- GAT NET.Lock Label GEA NUM right (Part No. 679236)
For right-hinged doors, with numbering
- GAT NET.Lock Label GEA left (Part No. 370022)
For left-hinged doors, without numbering
- GAT NET.Lock Label GEA NUM left (Part No. 679135)
For left-hinged doors, with numbering
7. Battery 3.6V Lithium SL-860/S* (Part No. 914430)
GANTNER approved battery for the GAT ECO.Side Lock 7000 BA. One battery required for operation.
Supplied per battery.
*SL-860/S (EU). TL-4903/S (US)
8. GAT ECO.Basic Set B BA (Part No. 958131)
Accessory set for configuring and maintaining the GAT ECO.Side Lock 7000 BA system. Contains system data
carriers, 3 m USB cable, configuration software, and GANTNER lanyard. See section “6.4. GAT ECO.Basic Set
B BA” for more information.
9. GAT Key Tag BA Open Master (Part No. 1100364)
Optional data carrier. Not included in the GAT ECO.Basic Set B BA. Can be used instead of another MASTER
data carrier in order to unlock a locked GAT ECO.Side Lock 7000 BA. Unlike the MASTER data carriers the
OPEN MASTER data carrier can only open but not lock a locker.

GAT ECO.Side Lock 7000 BA / NW BA
General Information
16 HB_GAT-GAT-ECOSide-Lock7000-BA--EN_14 www.gantner.com

GAT ECO.Side Lock 7000 BA / NW BA
Installation
www.gantner.com HB_GAT-GAT-ECOSide-Lock7000-BA--EN_14 17
3 INSTALLATION
This chapter describes the process and what must be considered to install the GAT ECO.Side Lock 7000 BA and NW BA
into lockers with metallic, non-metallic, and glass doors. Since the mounting process is identical for both lock variants,
the general term GAT ECO.Side Lock 7000 BA is used.
Risk of damage or failure to the GAT ECO.Side Lock 7000 BA
- Read the information in this section carefully before installing the GAT ECO.Side Lock 7000 BA.
- Carefully observe the installation diagrams.
- Use the correct tools to install the GAT ECO.Side Lock 7000 BA.
3.1 Target Group
This chapter provides information for technicians who install the GAT ECO.Side Lock 7000 BA. Experience in
mechanical work and basic electrical knowledge is required. Previous knowledge of the GAT ECO.SideLock 7000 BA
is not required.
3.2 Definition of the Door Hinge (Right of Left Door)
For installation, it is important to determine whether the door is hinged to the left or the right. This is defined as follows:
Figure 3.1 –Locker door hinge definition (left/right)
In the following pages the installation process for right-hinged doors is described. The installation process for left
locker doors is in principle the same as for right locker doors, only with reversed lock and door orientation.
NOTE! If spring hinges are used in the locker door, ensure that the spring strength is calibrated to allow correct
operation of the lock. For example, springs that are too strong can keep the bolt set permanently held in thereby
activating the lock’s electronics and draining the battery.

GAT ECO.Side Lock 7000 BA / NW BA
Installation
18 HB_GAT-GAT-ECOSide-Lock7000-BA--EN_14 www.gantner.com
3.3 Test Installation
As the GAT ECO.Side Lock 7000 BA is suitable for a wide range of installation applications, always perform a test
installation including functional testing of the GAT ECO.Side Lock 7000 BA in a sample locker from the facility before
starting with the mass production of lockers.
The following important points must be met. Ensure that:
- The door shackle slides centrally into the opening of the GAT ECO.Side Lock 7000 BA.
- The door locks without any problems.
- The door opens without resistance (ensure retaining hardware such as springs are correctly calibrated).
Also test the GAT ECO.Side Lock 7000 BA using a data carrier, ideally of the same type to be used with the locker
system, to ensure the data carrier functions as required. Once the test installation is successfully completed, the
remaining locks can be installed in the same way. An installation checklist is available from GANTNER to assist with
the test installation process.
3.4 Metallic and Non-Metallic Doors
Because the RFID field of the GAT ECO.Side Lock 7000 BA is distorted or blocked by metal, e.g., metallic locker
doors, a cutout is made in metallic locker doors into which the GAT NET.Lock Bolt Set 7200 and label carrier are
installed. A specific cutout for non-metallic doors is not necessary, only a drill hole for the status LED is required.
As the reading range of the GAT ECO.Side Lock 7000 BA is limited, the door of non-metallic lockers must not be too
thick. The maximum door thickness of non-metallic doors depends on the RFID technology and the type of data
carriers used.
3.5 Bolt Gauge
The bolt gauge (GAT NET.Lock Tool 7000, Part No. 533831) can be used to assist installation in non-metallic
doors. The gauge allows you to easily mark the drill hole positions onto the door.
Figure 3.2 –Bolt gauge (dimensions in mm)
The instructions for using the bolt gauge are included with the installation instructions for non-metallic doors (see
"3.10.2 Installation Instructions for the GAT ECO.Side Lock 7000 BA and Non-Metallic Doors").

GAT ECO.Side Lock 7000 BA / NW BA
Installation
www.gantner.com HB_GAT-GAT-ECOSide-Lock7000-BA--EN_14 19
3.6 Door Status Contact
The GAT ECO.Side Lock 7000 BA has a feedback contact (2 in Figure 3.3) that is activated by the door contact (1
in Figure 3.3) when the locker door is closed. It is important that this contact remains clean and undamaged to
ensure the correct functionality of the GAT ECO.Side Lock 7000 BA.
Figure 3.3 –Door status contact
3.7 Transportation Guidelines
The electronics of the GAT ECO.Side Lock 7000 BA are activated when the locker door is pressed shut. For
factory-produced lockers that use the GAT ECO.Side Lock 7000 BA, it is important to ensure the bolt set does not
activate the lock’s electronics during transportation or any time prior to delivery. Activation of the lock electronics
during transportation can decrease the battery lifetime.
3.8 Replacement after a Burglary Attempt
If a burglary (forced opening) is attempted or occurs in a locker, the entire GAT ECO.Side Lock 7000 BA must be
replaced with a new one. The bolt set and the door shackle must also be replaced.

GAT ECO.Side Lock 7000 BA / NW BA
Installation
20 HB_GAT-GAT-ECOSide-Lock7000-BA--EN_14 www.gantner.com
3.9 Measurement Diagrams for Installation
Door Width
The minimum door width allowed (measured from the door shackle to the hinge) is 230 mm (9.05´´). If the door is
narrower, the door shackle will hit the locker when the door is being closed.
Figure 3.4 - Minimum door width
Dimensions of the GAT ECO.Side Lock 7000 BA and GAT NET.Lock Bolt Sets
Figure 3.5 - Dimensions of the GAT ECO.Side Lock 7000 BA (dimensions in mm –inches shown in brackets)