GE AHH24DSH1 Operating instructions

GEAppliances.com
E
"0
Safety Instructions ............. 2,3
Operating Instructions
Controls ........................... 4-6
Care and Cleaning
Air Filter .............................. 6
Outdoor Coils ......................... 6
Installation Instructions ...... 7-12
Troubleshooting Tips ............ 13
Normal Operating Sounds ............ 13
Consumer Support
Consumer Support .......... Back Cover
Warranty for Customers
in the U.S.A ........................... 15
ENERGYSTAR_labeled product
I
ENERGYSTAR
As an ENERGYSTAR_partner, GE has
determined that this product meets
the ENERGYSTAR_guidelines for
energy efficiency.
Write the model and serial numbers here:
Model #
Serial #
Find these numbers on a label on the side of
the air conditioner,
AHH24
AHL24
49- 7724 7O-73 GE

IMPORTANT SAFETYINFORMATiON.
READALL INSTRUCTIONSBEFOREUSING
AWARNING!
For your safety, the information in this manual must be followed to minimize the risk of fire, electric
shock or personal injury.
.SAFETYPRECAUTIONS
Use this appliance only for its intended
purpose as described in this Owner's
Manual.
This air conditioner must be properly
installed in accordance with the Installation
Instructions before it is used.
Never unplug your air conditioner by pulling
on the power cord. Always grip plug firmly
and pull straight out from the receptacle.
Replace immediately all electric service
cords that have become frayed or otherwise
damaged. A damaged power supply cord
must be replaced with a new power supply
cord obtained from the manufacturer and
not repaired. Do not use a cord that shows
cracks or abrasion damage along its length
or at either the plug or connector end.
Turn the unit OFF and unplug your air
conditioner before cleaning.
GEdoes not support any servicing of the
air conditioner. We strongly recommend
that you do not attempt to service the air
conditioner yourself.
For your safety,,,do not store or use
combustible materials, gasoline or other
flammable vapors or liquids in the vicinity
of this or any other appliance.
All air conditioners contain refrigerants,
which under federal law must be removed
prior to product disposal. If you are getting
rid of an old product with refrigerants, check
with the company handling disposal about
what to do.
If the receptacle does not match the plug,
the receptacle must be changed out by a
qualified electrician.
These R410A air conditioning systems
require contractors and technicians to
use tools, equipment and safety standards
approved for use with this refrigerant.
DO NOT use equipment certified for
R22 refrigerant only.
2
HOW TOCONIVECTELECTRICITY
Do not, under any circumstances, cut or remove
the third (ground) prong from the power cord.
For personal safety, this appliance must be
properly grounded.
DO NOT use an adapter plug with this appliance.
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates
with a standard 3-prong (grounding) wall outlet
to minimize the possibility of electric
shock hazard from this appliance.
Power cord includes a current interrupter device.
A test and reset button is provided on the plug
case. The device should be tested on a periodic
basis by first pressing the TESTbutton and
then the RESETbutton while plugged into the
outlet. If the TESTbutton does not trip or if the
RESETbutton will not stay engaged, discontinue
use of the air conditioner and contact a qualified
service technician.
Have the wall outlet and circuit checked by
a qualified electrician to make sure the outlet
is properly grounded.
Where a 2-prong wall outlet is encountered,
it isyour personal responsibility and obligation to
have it replaced with a properly grounded
3-prong wall outlet.
The air conditioner should always be plugged
into its own individual electrical outlet which has
a voltage rating that matches the rating plate.
This provides the best performance and also
prevents overloading house wiring circuits which
could cause a fire hazard from overheated wires.
See the Installation Instructions, Electrical
Requirements section for specific electrical
connection requirements.

AWARNING!
USE OFEXTEIVSIOIVCORDS
RISK OFFIRE. Could cause serious injury or
death.
•DO NOTuse an extension cord with this
Window Air Conditioner.
•DO NOTuse surge protectors or multi-outlet
adaptors with this Window Air Conditioner.
GEAppliances.com
READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY.
SAVETHESEINSTRUCTIONS

About the controls on the air conditioner
Features and appearance will vary.
Lights next to the touch pads on the air conditioner controI panel indicate the selected settings.
UO
[] Auto
[] High
[] Med
[] Low
[]cool []On
[] Fan Only [] Off
[] a
Energy Saver
Unit power _41_*
on/off
Mode select
Fan speed _
Delay 1 24hr
Temperature
set/Delay
Timerlncrease
and Decrease=='='='l!_
f
D
|
Q
O
D
Air Conditioner Controls Remote Control
Controls
4
Power Pad
Turns air conditioner on and off. When turned
on, the display will show the room temperature.
Display
Shows the room temperature or time remaining
on the Delay timer. Shows the Settemperature
while setting the temperature in Coo/or Energy
Savermodes. The Set light will turn on while
setting.
Temp and Delay Increase A/Decrease V
Pads
Use to set temperature or delay time.
Temperature can be set in Cooland Energy
Saving and mode.
Mode Pad
Use to set the air conditioner to Fan Onlyor
Cool, Energy Saver mode,
Fan Speed Pads
In Cool, Energy Saving mode:
Use to set the fan speed to Auto, High, Medor
Lowon the unit.
In Fan Onlymode:
Use to set the fan speed to High, Meal, or Low
on the unit.
Reset Filter
LEDwill turn on when fan has accumluated 250
hours of run time as a reminder to clean filter.
Press Reset Filter to turn off the LED and reset
the accumulated run time.
De/a/Pad
Delay ON--When the air conditioner is off, it can
be set to automatically come on in 1 to 24 hours
at its previous mode and fan settings.
Delay OFF--When the air conditioner is on,
it can be set to automatically turn off in 1to
24 hours.
How to set:
Pressthe Delay 1-24hrpad on the unit or the
remote control. Each touch of the Increase A/
Decrease Y pads on the unit or the Increase +
/ Decrease = pads on the remote control will set
the timer in 1-hour intervals.
To review the remaining time on the Delay
1-24hrtimer, press the Delay 1-24hrpad on the
unit or the remote control. Use the Increase A/
Decrease Y pads on the unit or the Increase +
/ Decrease - pads on the remote control to set
a new time if desired.
To cancel the timer, press Decrease • pad on
the unit or the remote control until the set time
is zero. After 3 seconds the light on the Delay
1-24 hour pad goes off.

GEAppliances.com
Do Not Operate in Freezing Outdoor Conditlbns
This cool-only air conditioner was not designed for
freezing outdoor conditions, It must not be used in
freezing outdoor conditions,
Remote Control
, To ensure proper operation, aim the remote
control at the signal receiver on the air
conditioner,
, The remote control signal has a range of
up to 20 feet,
, Make sure nothing is between the air conditioner
and the remote control that could block the
signal,
, Make sure battery is fresh and installed correctly
as indicated on the remote control,
Cool Mode
Use the Coolmode at Low, Meal, High or Auto
Speedfor cooling, Use the Temperature Increase
+ / Decrease - pads to set the desired temperature
between 64°F and 86°F in I°F increments,
An electronic thermostat is used to maintain the room
temperature, The compressor will cycle on
and off to keep the room at the set level of comfort,
Set the thermostat at a lower number and the indoor
air will become cooler, Set the thermostat at a higher
number and the indoor air will become warmer,
NOTE:/fthe air conditioner is off and is then turned on
while set to aCool setting or if turned from af_n
setting to aCool setting, it may rake approxirnate_
3 minutes for the compressor to stuartand cooling to
begin,
Cooling Descriptions
For Normal Cooling-Select the Cool mode and
High or Medfan with a middle set temperature,
For Maximum Cooling-Select the Cool mode
and Highfan with a lower set temperature,
For Quieter and Nighttime Cooling- Select the
Coo/mode and Lowfan with a middle set
temperature,
Energy &aver Mode
Energy Saver mode conserves energy by optimizing
the cooling power of your air conditioner, Once the
desired temperature is reached, the fan will turn off to
save energy,
The fan will periodically turn back on to ensure that all
cooling capacity in the unit is used, This is the default
setting for all Energy Star air conditioners, and they
are intended
to operate this way, In addition, each time the unit is
powered down, it will re-start in Energy Saver mode,
This includes if the unit turns back on by the Time
Delay On/Off mode,
When Energy Saver mode is ON:
It is normal for the fan to cycle "Off" and then back
"On" in this mode, This on/off cycle can repeat
multiple times, Because the fan will cycle off, you may
notice a variation in room temperature and humidity,
When Energy Saver mode is OFF."
The fan will run continuously, and in Cool mode the
compressor will cycle on and off to maintain room
temperature,
To override Energy Saver mode, toggle the "Mode"
button from "Energy Saver" to "Fan" or "Cool" settings,
Fan Only Mode
Use the Fan Only Mode at Low, Med or High fan
speed to provide air circulation and filtering without
cooling, Since fan-only settings do not provide
cooling, a Set temperature cannot be entered, The
room temperature will appear in the display,
Auto Fan
Set to Auto for the fan speed to automatically set
to the speed needed to provide optimum comfort
settings with the set temperature,
If the room needs more cooling, the fan speed
will automatically increase, Ifthe room needs less
cooling, the fan speed will automatically decrease,

About the controls on the air conditioner
Additional important information.
Air Direction
Use the lever to adjust the air direction left, right, up -_-_-_
and down.
Care and cleanin of the air conditioner.
Grifle and Case
Turn the air conditioner off and remove the plug from To clean, use water and a mild detergent. Do not use
the wall outlet before cleaning, bleach or abrasives.
Air Filter
The air filter behind the front grille should be checked
and cleaned at least every 30 days or more often if
necessary.
To remove:
Open the inlet grille by pulling downward on the tabs
at the top upper corners of the inlet grille until the
grille is in a 45° position. Remove the filter.
Clean the filter with warm, soapy water. Rinse and let
the filter dry before replacing it. Do not clean the filter
in a dishwasher.
_' CAUTION:DoNoTo_r_t_th_air
conditioner without a filter because dirt and lint wi//
clog it and reduce performance,
Outdoor Coils
The coils on the outdoor side of the air conditioner
should be checked regularly. If they are clogged with
dirt or soot, they may be professionally cleaned.
6
How to Insert the Batteries in the Remote Control
r_ emove battery cover screw and
simultaneously push in the side and pull out the
plastic retainer to remove battery.
-] Insert new battery, making sure (+)
that the and
(-) of battery are installed correctly.
[-3-] Reattach the cover by snapping it into the
remote and replacing the screw.
NOTE$:
Use one CR 2025 (3V)Lithium battery.
Remove the batteries from the remote control if
the system is not going to be used for a long time.

Installation
Instructions Air Conditioner
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
" IMPORTANT - sove these instructions
for local inspector's use.
• IMPORTANT - Observeallgoverning
codes and ordinances.
• Note to Installer- Be sure to leave these
instructions with the Consumer.
Note to Consumer - Keep these instructions for
future reference.
• Skill level - Installation of this appliance requires
basic mechanical skills.
Completion time - Approximately 1 hour
We recommend thot two people instoll
this product.
Proper instollation is the responsibility
of the installer.
Product foilure due to improper installation is not
covered under the Warranty.
You HUST use all supplied parts and use proper
installation procedures as described in these
instructions when installing this air conditioner.
ELECTRICALREQUIREMENTS
Some models require a 115/120-volt AC,
60-Hz grounded outlet protected with a
15-amp time-delay fuse or circuit breaker.
The 3-prong grounding plug minimizes the
possibility of electric shock hazard. If the wall outlet
you plan to use is only a 2-prong outlet, it isyour
responsibility to have it replaced with a properly
grounded 3-prong wall outlet.
©
@Some models require 230/208-volt AC,
protected with a time-delay fuse or circuit
breaker. These models should be installed on
their own single branch circuit for best
performance and to prevent overloading
house or apartment wiring circuits, which
could cause a possible fire hazard from
overheating wires.
ACAUTION:
Do not, under any circumstances, cut or remove
the third (ground) prong from the power cord.
Do not change the plug on the power cord
of this air conditioner.
Aluminum house wiring may present special
problems-consult a quolified electricion.
TOOLS YOU WILL NEED
Phillips head screwdriver Drill with 1/8" bit
Flat-blade screwdriver Adjustable Wrench
Pencil Ruler or tape measure
Level Scissors or knife
Power cord includes a current interrupter device. A
test and reset button is provided on the plug case. The
device should be tested on a periodic basis by first
pressing the TESTbutton and then the RESETbutton
while plugged into the outlet. If the TESTbutton does
not trip or if the RESETbutton will not stay engaged,
discontinue use of the air conditioner and contact a
qualified service technician.

Installation Instructions
PARTSINCLUDED
(Appearance may vary)
Top mounting rail
\Top mounting
rail gasket Foam top window
Bottom seal gasket
Left and Right Side
Curtains
Installation Bracket (2) Window Lock Bracket
m
D
O
O
O
D@
Remote Control
Self-Tapping
Screw (12) Bracket Screws (6) Wood Screws (8) 2-1/2" Flat Head Bolt and Lock Nut (2)

Installation Instructions
R1 WINDOW REQUIREMENTS
• These instructions are for a standard
double-hung window. You will need to modify
them for other types of windows.
• The air conditioner can be installed without the
side curtain panels if needed to fit in a narrow
window. See the window opening dimensions.
All supporting parts must be secured to firm
wood, masonry or metal.
The electrical outlet must be within reach of the
power cord.
Follow the dimensions in the illustration for your
model.
J
D==4]
19 1/8"
29 1/4" - 40"
(Withsidecurtain panels)
cl-- 1
r21STORMWINDOW REQUIREMENTS
A storm window frame will not allow the air
conditioner to tilt toward the outside, and will
keep it from draining properly. To adjust for this,
attach a piece of wood to the sill.
WOOD PIECES
WIDTH: 2"
LENGTH: Long enough to fit inside the window
frame.
1/2" higher
than storm
window
frame
Storm window
frame
THICKNESS: To determine the thickness, place a
piece of wood on the sill to make it 1/2" higher
than the top of the storm window frame or the
vinyl frame.
Attach securely with nails or screws provided
by the installer. 1/2" higher
than vinyl frame
_ (on some windows)
D] PREPARETHE AIR CONDITIONER
[] Remove three screws from each side of the
case. The front two screws will be reinstalled
later.
D
F1
Insert a flat head screw driver between the
front grille and the metal case along the sides.
Gently pry the grille from the case. NOTE: Cover
the flat head screw driver with tape to prevent
scratching the case.
Using the handle on bottom front of the air
conditioner, pull air conditioner out of the case.
The air conditioner is very heavy so make sure
that it will be resting on a sturdy surface.

Installation Instructions
[] PREPARETHE CASE
NOTE:Attach curtains to the air conditioner
before placing the air conditioner in window.
r_ Install the top mounting rail with four type A
screws,
r_ Slide left-hand curtain assembly into left end
of top and bottom mounting rail. Repeat for
right-hand curtain assembly.
r_ Fasten curtain retainer strips to the sides of the
outer case with three type A screws on each
side.
A\\
A. Top mounting rail
B. Type A screws C. Type Ascrews
D. Sidecurtains
El PREPAREWINDOW FOR INSTALLATION
r_ Measure the width of the window opening.
r_ Mark the center line on the inside windowsill.
B
A.Width of window opening
B.Center line
r_ INSTALL OUTER CASE IN WINDOW
[] Place outer case in window, Lower sash until it
rests behind front flange of top mounting rail,
Bottom mounting rail must rest behind window
sill. Top rail
_ Window sash
o
Bottom rail
So
El
rq
Expand the curtain panels to fill the window.
Secure with type C wood screw in top corners.
If needed, use drill and 1/8" bit to drill pilot holes
for the screws.
Use three type C screws to secure the top
mounting rail to the window. Drill pilot holes if
necessary.
10

Installation Instructions
r_ INSTALL OUTER CASE IN WINDOW
r_ Thread nut onto bolt, then thread the bolt into
the triangle bracket as shown in the figure
below.
B
Screws
[[] Attach triangle bracket onto bottom of case
using three type B screws for each bracket.
Make sure that the bracket is close enough to
the outside wall that the bolt can touch. Adjust
bolt so that it is snug against the outside wall.
1
NOTE: A block of wood can be placed between
the bolt and the outside wall if the bolt rests
between studs.
D COMPLETEINSTALLATION
[_ Insert the foam seal behind the top of the lower
window sash and against the glass of the upper
window.
A,Top of lower window sash
B,Foam seal
_] Place the window lock bracket as shown. Use
a 1/8" drill bit to drill a starter hole through the
hole in the window lock bracket and into the
upper window.
,&CAUTION"
To prevent broken glass or damage to windows,
on vinyl or other similarly constructed windows,
attach the window locking bracket to the
window side jamb with one type B screw.
[] Attach the window lock bracket to the upper
window with a type C screw to secure the
window in place.
Vinyl Wood
C
Screws
11

Installation Instructions
[B] RETURN CHASSIS TO THE OUTER CASE
r_ Once the case is securely attached to the
window, reinstall the air conditioner. Have two
people lift the air conditioner and slide it into the
case.
r_ Snap the front grill back onto the air conditioner.
Use the screws removed at the beginning of the
installation to secure the grille.
[_ RETURN CHASSIS TO THE OUTER CASE
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
r_ Plug into a grounded 3-prong outlet.
r_ Press RESETon the power supply cord. See
E/ectrica/ Requirements.
12

Possible Causes What To Do
Air conditioner The air conditioner . Hake sure the air conditioner plug is pushed
does not start is unplugged, completely into the outlet,
The fuse is blown/circuit . Check the house fuse/circuit breaker box and replace
breaker is tripped, the fuse or reset the breaker,
Power failure. .The unit will automatically restart in the settings last
used after the power is restored,
.There is a protective time delay (approximately
3 minutes) to prevent tripping of the compressor
overload, For this reason, the unit may not start
normal cooling for 3 minutes after it is turned
back on,
The current interrupter .Press the RESETbutton located on the power cord plug,
device is tripped. .If the RESETbutton will not stay engaged, discontinue
use of the air conditioner and contact a qualified
service technician,
Air conditioner does Airflow is restricted. , Hake sure there are no curtains, blinds or furniture
not cool as it should blocking the front of the air conditioner,
The temp control may • In the Coolmode, press the Decrease - pad,
not be set correctly.
The air filter is dirty. • Clean the filter at least every 30 days.
See the Cnre and C/e_ning section,
The room may have been hot. . When the air conditioner isfirst turned on, you need
to allow time for the room to cool down,
Cold air is escaping. • Check for open furnace registers and cold air returns.
Cooling coils have iced up. .See "Air conditioner freezing up" below.
Ice blocks the air flow . Set the controls at High Fan or High Cooland set the
freezing up and stops the air conditioner thermostat to a higher temperature,
from cooling the room.
The remote control The battery is inserted . Check the position of the battery. They should be
is not working incorrectly, inserted in the opposite (+)and (-) direction,
The battery may be dead. . Replace the battery.
Water drips outside Hot, humid weather. . This is normal.
Water drips indoors The air conditioner is not . For proper water disposal, make sure the air conditioner
tilted to the outside, slants slightly from the case front to the rear,
Water collects in Moisture removed from air . This is normal for a short period in areas with little
base pan and drains into base pan. humidity; normal for a longer period in very humid areas,
Normal Operating Sounds
, You may hear u pinging noise caused by
water being picked up and thrown against the
condenser on rainy days or when the humidity
is high, This design feature helps remove
moisture and improve efficiency,
, Youmay hear the thermostat clickwhen the
compressor cycles on and off,
Water will collect in the base pan during
high humidity or on rainy days, The water
may overflow and drip from the outdoor side
of the unit,
The fan may run even when the compressor
does not,
13

Note
14

GE Air Conditioner--One-Year Limited Warranty. (For customers in the US, A)
All warranty service provided by our Factory Service Centers,
or an authorized Customer Card _'mchnician. Toschedule service,
visit us on-line at GEAppliances.com, or call 800. GE.CARES
(800.432.2737). Have serial number and model number available
when calling for service.
St_?pleyour receipt here,
Proof of the original purchase
d_?teis needed to obt_?in service
under the warranty,
one year
From thedate ofthe
origina!purchase
GE Will Replace:
Anypart of the air conditioner which fails due to a defect in materials or workmanship,
During this limited one-year warranty, GEwill also provide, free of charge, all labor and related
service to replace the defective part,
Service trips to your home to teach you how to
use the product.
Improper installation, delivery or maintenance. If you
have an installation problem, or if the air conditioner
is of improper cooling capacity for the intended use,
contact your dealer or installer. You are responsible
for providing adequate electrical connecting facilities.
Failure of the product resulting from modifications to
the product or due to unreasonable use including failure
to provide reasonable and necessary maintenance.
]n commercial locations, labor necessary to move the
unit to a location where it is accessible for service
by an individual technician.
Replacement of house fuses or resetting of circuit
breakers.
, Failure due to corrosion on models not corrosion-
protected.
, Damage to the product caused by improper power
supply voltage, accident, fire, floods or acts of God.
, Incidental or consequential damage caused by possible
defects with this air conditioner.
Damage caused after delivery.
EXCLUSION OF IMPLIED WARRANTIES--Your sole und exclusive remedy is product repuir us provided in
this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or
fitness for a particular purpose, are limited to one year or the shortest period allowed by law.
This warranty is extended to the original purchaser and any succeeding owner for products purchased for
home use within the USA. ff the product is located in an area where service by a GEAuthorized Servicer is
not available, you may be responsible for atrip charge or you may be required to bring the product to an
Authorized GEService location for service, in Alaska, the warranty excludes the cost of shipping or service calls
to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty
gives you specific legal rights, and you may also have other rights which vary from state to state. Toknow
what your legal rights are, consult your local or state consumer affairs office or your state's Attorney General.
Warrantor: General Electric Company. Louisville, K}/ 40225
15

Consumer Support.
GEAppliances Website In the U.S.A.: GEAppliances.com
Have a question or need assistance with your appliance? Try the GEAppliances Website 24 hours a day,
any day of the year! For greater convenience and faster service, you can now download Owner's Manuals,
or even order parts on-line, In Canada; www,GFAppliances,ca
Studio In the U.S.A.: GEAppliance&com
GEsupports the Universal Design concept-products, services and environments that can be used by
[ people of all ages, sizes and capabilities, We recognize the need to design for a wide range of physical
Jand mental abilities and impairments, For details of GE's Universal Design applications, including kitchen design
ideas for people with disabilities, check out our Website today, For the hearing impaired, please call 800,TDD,
GEAC(800,833,4322),
In Canada, contact; Manager, Consumer Relations, Mabe Canada Inc,
Suite 310, 1 Factory Lane
Moncton, N,B,E1C9M3
Parts and Accessories In the U.S.A.: GEAppliances.com
Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes
(VISA,MasterCard and Discover cards are accepted), Order on-line today, 24 hours every day or
by phone at 800,626,2002 during normal business hours,
Instructions contained in this manual cover procedures to be performed by any user, GEdoes not support
any servicing of the air conditioner, We strongly recommend that you do not attempt to service the air
conditioner yourself,
Customersin Canada should consult the yellow pagesfor the nearest Mabe servicecenter,
or call 1,800,561,3344,
Contact Us In the U.S.A.: GEAppliances.com
If you are not satisfied with the service you receive from GE,contact us on our Website with all the details
including your phone number, or write to; General Manager, Customer Relations
GEAppliances, Appliance Park
Louisville, KY80225
In Canada: www.GEAppliances.ca, or write to: Director, Consumer Relations, Mabe Canada Inc.
Suite 310, 1 Factory Lane
Moncton, N.B.E1C9M3
"] 6 Printed in China

GEPpp/iance&com
0
"0
0
im
"0
0
o")
L_
Instrucciones de Seguridad... 2,3
Instrucciones de Funcionamiento
Controles ............................. 4
Cuidado y Limpieza
Bobinas Exteriores .................... 5
Filtro de Aire .......................... 5
Jnstrucciones de Instalacion. 6-10
Conse]os para Solucionar
Problemas ......................... 11
Sonidos Normales de
Funcionamiento ..................... 11
Soporte al Cliente
Garantia para Clientes en EE.UU ...... 13
Soporte al Cliente .................... 14
Producto etiquetado *ENERGYSTAR#>
J
ENERGYSTAR
Corrlo socio de.ENERGYSTAR_>,
GEha confirmado que este
producto cumple I_s directrices
de ENERGYSTAR_>relativas a/
rendimiento energetico,
Escriba los nElmeros de mode/o y de serie
aquL"
N° de Modelo
N ° de Serie
Estos numeros se encuentran en una
etiqueta al costado del acondicionador de
aire
AHH24
AHL24
49- 7724 70- 73 GE

INFORMACION IMPORTANTEDE SEGURIDAD.
LEA TODASLAS INSTRUCCIONESANTES DE USAR.
AiADVERTENCIA!
Por su seguridad, se debe seguir la informacion en este manual para minimizar el riesgo de
incendios, descargas eBctricas o lesiones personales.
2
PRECAUCIONESDESEGUR/DAD
Use este electrodomestico solamente para
el proposito determinado segun se describe
en el Manual del propietario.
Este acondicionador de aire debe instalarse
correctamente de acuerdo con las
Instrucciones de instalacion antes de su uso.
Nunca desenchufe su acondicionador de
aire tirando del cable electrico. Siempre
agarre firmemente el enchufe y tire de
el directamente hacia afuera.
Reemplace inmediatamente todos los
cables electricos que se hayan pelado o que
se hayan dahado de alguna otra manera.
Un cable de corriente dahado no debe
repararse, sino que debe ser sustituido pot
uno nuevo que se adquiera del fabricante.
No use un cable electrico que muestre
evidencias de deterioro, o dahos de
abrasion en su superficie en alguno de sus
extremos.
Apague la unidad y desenchufe su
acondicionador de aire antes de limpiar.
GE no esta no apoya que se le proporcione
ningt_n servicio al acondicionador de aire.
Vehementemente recomendamos que
usted no intente proporcionar servicio al
acondicionador de aire usted mismo.
Por su seguridad,,,no almacene ni use
materiales combustibles, gasolina u
otros vapores o liquidos inflamables
en la proximidad de este o algun otro
electrodomestico.
Todos los acondicionadores de aire
contiene reffigerantes, los que pot Ley
Federal deben ser removidos antes de
desecharlos. Si usted planea deshacerse de
algtin producto que contenga refrigerantes,
pongase en contacto con la compahia que
se encarga de recoger su basura para que
le indiquen que hacer.
Si el receptaculo no coincide con el enchufe,
un electricista calificado debe reemplazar el
receptaculo.
Estos sistemas de acondicionadores de
aire R41OArequieren que los contratistas
y tecnicos usen herramientas, equipos y
estandares de seguridad aprobados para
su uso con este reffigerante. NO use
equipamiento certificado solo para
refrigerante R22.
COMOCONECTARLA ELECTR/C/DAD
Bajo ninguna circunstancia, corte o remueva la
tercera pt_a (tierra) del cable eBctrico. En pos
de la seguridad personal, este electrodomestico
debe siempre conectarse a tierra.
NO use un enchufe adaptador con este
electrodomestico.
El cable electrico de este electrodomestico esta
equipado con un enchufe de tres ptias (tierra)
que combina con un tomacorriente estandar
de tres tomas de pared para minimizar la
posibilidad de una descarga electrica.
El cable de alimentacion incluye un
dispositivo para interrupcion de corriente.
Se incluye un boron de prueba y de reinicio
en el dispositivo. El dispositivo debe ponerse
a prueba periodicamente: primero se presiona
el boron de TEST(prueba)y luego RESET
(reinicio) mientras se encuentra enchufado al
tomacorriente. Si el boron TESTno se dispara
o si el boron RESETno queda enganchado,
deje de utilizar el acondicionador de aire y
comuniquese con un tecnico calificado.
Pida a un tecnico que inspeccione el
tomacorriente y el circuito para cerciorarse
de que el tomacorriente esta conectado a
tierra de la manera apropiada.
Donde exista un tomacorriente de dos
tomas, es su responsabilidad y obligacion
personal hacer que dicho tomacorriente
sea reemplazado por uno de tres tomas
con conexion a tierra.
El acondicionador de aire deberia siempre estar
conectado a un tomacorriente individual con su
circuito de voltaje correspondiente.
Esto proporciona el mayor rendimiento y
ademas evita que los circuitos del resto de
la casa se sobrecarguen, Io cual podria causar
incendios pot el sobrecalentamiento del
cableado.
Vet las Instrucciones de instalacion, en la
seccion Requisitos Electricos para los requisitos
especificos de conexion.

GEAppliances.com
AiADVERTENCIA!
USODEPROLOA/CADORES
RIESGO DE INCENDIO. Podria ocasionar
lesiones gra yes o la muerte.
,, NO use un prolongador con este
Acondicionador de Aire de Ventana.
NO use protectores contra picos de corriente
ni adaptadores para mL_ltiplestomacorrientes
con este Acondicionador de Aire de Ventana.
LEAYSIGAESTAINFORMACIONDESEGURIDADCUIDADOSAMENTE.
GUARDEESTASINSTRUCCIONES

Acerca de los controles en el acondicionador de aire
Las funciones y la apariencia podran variar.
Las /ucesjunto a/as teclas tacti/es de/panel de control de/acondic/onador de a/re/ndican/as configurac/ones
selecc/onadas.
NOTA: La pantalla siempre muestra la
temperatura del ambiente, excepto al
UO
[] Auto
[] High
[] Med
[] Low
mcool "On
[] Fan Only [] Off
[] a
Energy Saver
Encendido/
apagado de la
Unidad
Seleccion de
modo
Velocidad del
ventilador
Retraso de 1 a
24 hrs,
Incremento
y Reduccion
de la
Configuracion
de
Temperatura/
Temporizador
de Retraso
f
O
D
Q
O
D
Controles del Acondicionador de AJre Control Remoto
4
Contro/es
Tecla de Power (Encendido)
Apaga y prende el acondicionador de aire,
AIencenderse, la pantalla mostrara la temperatura
ambiente,
_Pantalla
Muestra la temperatura ambiente o el tiempo
restante en el Sincronizador de retardo, Muestra
la temperatura Definida al configurar la
temperatura en los modos Cool{Fr[o)o de Energy
Saver (Ahorro de energla) La luz de Ajuste se
Tecla de Retraso
Delay ON (Retraso Encendido)-Cuando el
acondicionador de aire se encuentre apagado,
se podra configurar para que se encienda
automaticamente en un periodo de entre 1
y 24 horas en el modo y configuraciones del
ventilador previas,
Delay OFF (Retraso del Apagado)--Cuando el
acondicionador de aire se encuentre encendido,
se podra configurar automaticamente para que
encendera durante la configuracion,
Teclas de Temp Aumento +/Reduccidn -
Usado para ajustar la temperatura cuando
se encuentre en el modo Cool (Frio) oEnergy
Saver (Ahorro de energfa) La luz de Ajuste se
encendera durante la configuracion,
Tecla de MODO
Usado para ajustar el acondicionador de aire
almodo Cool (Frfo),Energy Savet (Ahorro de
energfa) oAuto (Autom4tico).
se apague en un periodo de entre 1y 24 horas,
Como configurar;
Presione la tecla Delay 1-24hr(Retraso
entre ly24hrs.) en la unidad o en el control
remoto, Cada vez que presione las teclas
Increase (Incrementar) +/Decrease (Reducir)
- de la unidad o control remoto se ajustara el
temporizador pot intervalos de 1 hora,
Para revisar el tiempo restante en el
temporizador de Delay 1-24hr (Retraso entre
ly24 hrs), presione la tecla Delay 1-24hr
Teclas de Fan Speed (Ve/ocidad del ventilador)
Use las mismas para configurar la velocidad
del ventilador en Low (Bajo), Med (Medio), o High
(Alto) en la unidad,
Reinicio del Filtro
La luz LED se encendera cuando el ventilador
haya acumulado 250 horas de funcionamiento,
como un recordatorio de que el filtro debe ser
limpiado, Presione ResetFilter(Reinicio del Filtro)
para apagar la luz LEDy reiniciar el tiempo de
funcionamiento acumulado,
(Retraso entre ly24 hrs.)de la unidad o
del control remoto, Use las teclas Increase
(Incrementar) + / Decrease (Reducir) - de la
unidad o control remoto para configurar un
tiempo nuevo si asi Io desea,
Para cance/ar el temporizador, presione
la tecla Delay 1-24hr (Retraso entre l y 24
hrs.)hasta que la luz de la tecla Delay 1-24hr
(Retraso entre l y24 hrs.)se apague,