GE 22158 User manual

3 Speed Wall Control for Fans
MODEL: 22158
User Manual
120V 60Hz, MADE IN CHINA
Customer Assistance
1-866-885-4649
[email protected]
Register your GE Branded product for warranty coverage on
www.gelightingandfans.com
Contact a qualified electrician or call the Customer Care Service Team at 1-866-885-4649
Customer Service hours of operation are 9:00AM-5:00PM EST -Monday-Friday
[email protected]

Safety Rules
Parts List
READ AND SAVE THESE INSTRUCTIONS
1. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box
before beginning.
2. All electrical connections must be made in accordance with local codes, ordinances and/or the National
Electric Code. Electrical installation should be performed by a qualified licensed electrician.
3. CAUTION: To reduce the risk of fire or injury, do not use this product in conjunction with any variable
(rheostat) wall control.
4. CAUTION: Do not use control with a fan and light that operate with the same switch.
5. WARNING: Do not connect wires across live/hot and neutral. This switch must only break the live/hot
line. Connecting the wires across live/hot and neutral will damage the control permanently.
6. Use only one control in a 3-way circuit.
7. Use control with a ceiling paddle fan only. Use only one ceiling paddle fan per control.
panel in white panel in ivory
wall control #6-32x 3/4"
screws 23A 12V
battery
wire nuts
1

Wall Control Installation
BLACK
BLACK
BLACK
BLACK
GREEN
/BARE
GREEN
2
1
2
3
3A
Shut OFF power to the switch at circuit breaker or fuse box . Verify power is OFF on the switch box
before continuing.
Remove the existing wallplate and switch from switch box.
Determine the type of circuit to make the wiring. Normally the switch is wired with a single pole switch or 3-
way switch. Please follow below wiring instructions.
IMPORTANT NOTE: Your wall switch may have two wires attached to the same screw as shown
below. Tape these two wires together before disconnecting.
TAPE
TAPE
AB
or
CAUTION: Please if you are not contact a qualified electrician, or call customer service 1-866-885-4649
certain of wiring.
WARNING: Do not connect wires across LIVE/HOT and NEUTRAL. This control must only break the
LIVE/HOT line.
SINGLE-POLE APPLICATION
BLACK
BLACK
GREEN/BARE
-Connect one black wire from the wall control to one of the black wires removed from the switch.
-If your switch box has a ground wire (green or bare copper), connect the green wire from the wall
control to the ground wire removed from the switch. If not , connect the green wire from the wall
control directly to one of the screws on the switch box.
If you had taped together two black wires from the switch, connect both wires to the control.
-Connect the second black wire from the wall control to the other black wire removed from the switch.
Secure wire nuts to ensure that no bare wire is exposed.

Wall Control Installation
BLACK
RED
BLACK
BLACK
GREEN
/BARE
GREEN
TAG
-If your switch box has a ground wire (green or bare copper), connect the green wire from the wall
control to the ground wire removed from the switch. If not , connect the green wire from the wall
control directly to one of the screws from the switch box.
- Connect one black wire from the wall control to the tagged wires removed from the switch.
RED
BLACK
GREEN
/BARE
TAG
3B 3-WAY APPLICATION
- Connect second black wire from the wall control to the other black wire removed from the switch.
- Cap off the red wire removed from the switch.
If you had taped together two black wires from the switch, connect both wires to the control.
Secure wire nuts to ensure that no bare wire is exposed.
4
5
6
7
8
Secure wall control to the switch box using the screws provided.
Install the 23A 12V battery provided into the compartment.
Secure a decor style wall plate to the wall control using the screws that come with the wall plate.
Attach the panel to the wall control, aligning the holes.
REFER TO DIAGRAM SHOWN BELOW TO COMPLETE INSTALLATION
3
Slide the ON/OFF switch on the wall control to “ON” position.
Panel

Operation Indicator
Low Speed
Medium Speed
High Speed
“ O ” and “ I ” dim switch
Wall Control Operation
4
NOTE:
-To prevent damage to transmitter, remove the battery if not used for long periods.
-Please contact your local batteries recycling center for proper battery disposal information.
For this fan, the dim switch should be in
the “I” position, allowing for dimming of
the light. Place the switch in the “0"
position to turn the dimming feature off
if you do not want the dimming feature.
NOTE:
For convenience, the transmitter has been
preset by the factory in the unlock position.
With this setting the transmitter will work
with GE Branded compatible fans without any
further programing.
-Lock/unlock switch when placed in the unlock position allows a common code to be sent .
In the unlock position : The transmitter will send a common code, this transmitter will operate all other GE BRANDED fans with the same receiver
configuration.
In lock position : Allows a unique code to be sent to the receiver in the fan. Only the receiver of this fan will be synced with this transmitter in
lock position. More than one fan can be synced with one transmitter, in this case-follow sync instruction for each fan.

5
Wall Control Syncing
Step 2. Install the 23A 12V battery provided.
Hold button to cycle between maximum and
minimum light.
Step 3. Within 30 sec, switch the lock “ ” / unlock
“ ” switch on the front of the transmitter to lock
position. And then push the sync “ ” button for
approximately 5-10 sec, until the fan light kit
flashes 3 times.
Step 1. Switch off the power to the fan.
Step .2 Use the on/off switch on the transmitter to
Trouble Shooting
CAUTION: Shut off main power supply before carrying out any of these checks.
In Case Of Interference With Several Fans, You Can Change
The Transmitter Code To Operate A Single Fan Only.
1. Fan will not start:
-Check main and branch circuit fuses or breakers.
-Check to make sure the wall switch is in the on position.
2. Remote control will not work:
- Ensure the control is wired correctly and receiving power.
- Ensure battery is new and installed correctly.
- Ensure the switches are set correctly.
- Sync the remote by following the syncing procedure above.
turn power on to the fan.

Specification
6
FCC ID: 2AAZPFAN67T3SP / I C : 11037A-FAN67T3SP
This device complies with part 15 of the FCC Rules and RSS-210 Issue 8. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may cause undesired
operation.
CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device
pursuant to part 15 of the FCC Rules and the limits pursuant to RSS-210 Issue 8.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and the receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Factory Model:FAN-67T-3SP
Rating: 120V~ 60Hz Max.2A

MODÈLE: 22158
120V 60Hz, FABRIQUÉ EN CHINE
Commande murale 3 vitesses pour ventilateurs
Manuel de l’utilisateur
Assistance à la clientèle
1-866-885-4649
[email protected]
Contacter un maître technicien ou appeler l’équipe du service après-vente au 1-866-885-4649
Les heures d’ouverture du service après-vente sont de 9 h à 17 h (Heure de l’Est) du lundi au vendredi
[email protected]
Enregistrez votre produit de la MARQUE GE pour la couverture de garantie sur
www.gelightingandfans.com

Consignes de sécurité
Liste des pièces
LIRE ET CONSERVER CES INSTRUCTIONS
1. Afin de réduire le risque de décharge électrique, s’assurer que l’alimentation électrique est coupée à partir du
disjoncteur ou de la boîte à fusibles avant de commencer.
2. Toutes les connexions électriques doivent être conformes aux codes locaux, décrets et/ou au Code électrique
national. L’installation électrique doit être effectuée par un maître électricien.
3. ATTENTION : Afin de réduire le risque d’incendie de blessure, ne pas utiliser ce ventilateur avec une
commande murale régulatrice (rhéostat).
4. ATTENTION : Ne pas utiliser la commande avec un ventilateur et une lumière qui fonctionnent avec le
même commutateur.
5. AVERTISSEMENT : Ne pas connecter les fils sur une ligne sous tension/à chaud et neutre. Ce commutateur
ne peut couper que la ligne sous tension/à chaud. La connexion des fils sur une ligne sous tension/à chaud et
neutre endommagera la commande de façon permanente.
6. Utiliser uniquement une commande sur un circuit 3 voies.
7. Utiliser la commande uniquement un ventilateur de plafond à pales. Utiliser uniquement un ventilateur de
plafond à pales par commande.
panneau blanc panneau ivoire
Commande murale vis #6-32x3/4" pile 23A 12V marrettes
1

Installation de la commande murale
2
1
2
3
3A
Couper l’alimentation (OFF) du commutateur au niveau du disjoncteur ou de la boîte à fusibles. Vérifier
que l’alimentation est coupée (OFF) au niveau du boîtier de l’interrupteur avant de poursuivre.
Retirer la plaque murale existante et commuter depuis le boîtier de l’interrupteur.
Identifier le type de circuit pour effectuer le câblage. Normalement, le commutateur est connecté par un fil
avec un commutateur unipolaire ou un commutateur 3 voies. Suivre les instructions ci-dessous pour
procéder au câblage
REMARQUE IMPORTANTE : Le commutateur mural peut avoir deux fils fixés à la même vis comme
indiqué ci-dessous. Attacher ces deux fils ensemble avec de l’adhésif avant la déconnexion.
RUBAN
ADHÉSIF
RUBAN
ADHÉSIF
AB
ou
ATTENTION : Contacter un maître électricien ou appeler le service clientèle au 1-866-885-4649 concernant
les questions sur le câblage.
AVERTISSEMENT : Ne pas connecter les fils sur une ligne SOUS TENSION/À CHAUD et NEUTRE. Cette
commande ne peut couper que la ligne SOUS TENSION/À CHAUD.
3A APPLICATION UNIPOLAIRE
NOIR
NOIR
NOIR
NOIR
NOIR
NOIR
VERT/NU
VERT
/NU
VERT
- Connecter un fil noir de la commande murale à l’un des fils noirs retirés du commutateur.
- Si votre boîtier de l’interrupteur possède un fil de terre (vert ou cuivre nu), connecter le fil vert de la
commande murale au fil de terre retiré du commutateur. Sinon, connecter le fil vert de la commande murale
directement à l’une des vis du boîtier de l’interrupteur.
Si vous avez attaché les deux fils noirs du commutateur ensemble avec de l’adhésif, connecter les deux
fils à la commande.
- Connecter le deuxième fil noir de la commande murale à l’autre fil noir retiré du commutateur.
Fixer les marrettes pour garantir qu’aucun fil nu n’est exposé.