GE IC693CBL300 User manual

QuickPanel™ Control
Communication Module
Quick Installation Guide
PCIF I/O Adapter
April 2010
GFK-2245A

GFL-002
Warnings, Cautions, and Notes as Used in this Publication
Warning
Warning notices are used in this publication to emphasize that hazardous voltages,
currents, temperatures, or other conditions that could cause personal injury exist in
this equipment or may be associated with its use.
In situations where inattention could cause either personal injury or damage to
equipment, a Warning notice is used.
Caution
Caution notices are used where equipment might be damaged if care is not taken.
Note: Notes merely call attention to information that is especially significant to under-
standing and operating the equipment.
This document is based on information available at the time of its publication. While efforts
have been made to be accurate, the information contained herein does not purport to cover
all details or variations in hardware or software, nor to provide for every possible contingency
in connection with installation, operation, or maintenance. Features may be described herein
which are not present in all hardware and software systems. GE Intelligent Platforms as-
sumes no obligation of notice to holders of this document with respect to changes subse-
quently made.
GE Intelligent Platforms makes no representation or warranty, expressed, implied, or statu-
tory with respect to, and assumes no responsibility for the accuracy, completeness, suffi-
ciency, or usefulness of the information contained herein. No warranties of merchantability
or fitness for purpose shall apply.
* Indicates a trademark of GE Intelligent Platforms, Inc. and/or its affiliates. All other
trademarks are the property of their respective owners.
©Copyright 2010 GE Intelligent Platforms North America, Inc.
All Rights Reserved

Contact Information
If you purchased this product through an Authorized Channel Partner, please contact the
seller directly.
General Contact Information
Online technical support and GlobalCare http://www.ge-ip.com/support
Additional information http://www.ge-ip.com/
Solution Provider solutionprov[email protected]
Technical Support
If you have technical problems that cannot be resolved with the information in this guide,
please contact us by telephone or email, or on the web at www.ge-ip.com/support
Americas
Online Technical Support www.ge-ip.com/support
Phone [phone]
International Americas Direct Dial 1-780-420-2010 (if toll free 800 option is unavail-
able)
Technical Support Email [e-mail]
Customer Care Email [e-mail]
Primary language of support English

Contact Information
Europe, the Middle East, and Africa
Online Technical Support www.ge-ip.com/support
Phone [phone]
EMEA Direct Dial [phone] (if toll free 800 option is unavail-
able or if dialing from a mobile telephone)
Technical Support Email [e-mail]
Customer Care Email customercare.eme[email protected]
Primary languages of support English, French, German, Italian, Czech, Spanish
Asia Pacific
Online Technical Support www.ge-ip.com/support
Phone [phone]
[phone] (India, Indonesia, and Pakistan)
Technical Support Email [e-mail] (China)
[e-mail] (Japan)
[e-mail] (remaining Asia customers)
Customer Care Email [e-mail]
[e-mail] (China)

The PCIF I/O Adapter has been tested and found to meet or exceed the requirements of
U.S. (47 CFR 15), Canadian (ICES-003), Australian (AS/NZS 3548) and European
(EN55022) regulations for Class A digital devices when installed in accordance with guide-
lines noted in this manual.
Note: This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received that may cause undesired
operation.
Note: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communica-
tions. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
Note: This Class A digital apparatus complies with Canadian ICES-003.
The following statements are required to appear for Class 1, Div 2 Hazardous Locations.
1. EQUIPMENT LABELED WITH REFERENCE TO CLASS 1, GROUPS A, B, C, AND
D, DIV 2 HAZARDOUS LOCATIONS IS SUITABLE FOR USE IN CLASS 1, DIVISION
2, GROUPS A, B, C, D, OR NON-HAZARDOUS LOCATIONS ONLY.
2. WARNING - EXPLOSION HAZARD - SUBSTITUTION OF COMPONENTS MAY
IMPAIR SUITABILITY FOR CLASS 1, DIVISION 2.
3. WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT EQUIPMENT
UNLESS POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE
NONHAZARDOUS.
The communication card meets ATEX Group II Category 3 when installed properly in a
QuickPanel Control OI.

6 Installation
Installing a Communication Module
Warning: Always use anti-static precautions when ac-
cessing the mating connector or the interior
of the unit.
Note: The 6” model QuickPanel is shown. Other models are
similar.
1. Disconnect the DC input power terminal block connec-
tor from your QuickPanel Control unit before connect-
ing the Communication Module to the unit.

Installation 7
2. Open the back cover.
3. Attach the Communication Module to the unit by plug-
ging the module into the mating connectors on the back
of the unit.
4. Install the three screws to secure the card in the unit.
5. Close the cover.
Connect your I/O network to external connections on the
module enclosure (see applicable sections for details).
Caution: Be sure to properly align pins in the dual
connector upon insertion to avoid damage to the
card or the QuickPanel Control.

8 Specification s
Series 90-30 Remote I/O Connector
Pin # Signal Direction
1 SHLD N/A
2 DFRAM E + Output
3 DFRAM E - Output
7 GND N/A
8 RUN + Output
9 RUN - Output
12 P ERR + Input
13 P ERR - Input
16 DA TA + Input/Output
17 DA TA - Input/Output
20 R SEL + Output
21 R SEL - Output
24 IOCLK + Output
25 IOCLK - Output

Installation 9
Interconnecting Cable
The cable used should have seven twisted pairs, with an
overall shield and drain wire (Belden 8107 or equivalent).
The final rack on the I/O Bus should be terminated with an
I/O Bus terminator plug, catalog number IC693ACC307.
Interconnecting cables may be standard length GE expan-
sion cables or custom length cables.
Part Number Cable Type
IC693CBL300 1 meter “Wye” cable
IC693CBL301 2 meter “Wye” cable
IC693CBL302 15 meter “point to point” cable
Environmental Specifications
Storage Temperature -20° to 70°C
Operating Temperature 0° to 60°C
Operating Humidity 5 to 90% (non-condensing)