Ge Bf50em User manual

BF50EM, BF100EM, BF120EM,

BF125EM, BF145EM

Easy Mount Bath Fan User’s Guide

210572119 Rev. D 1-08

Item Stock Number(s): BF50EM, BF100EM, BF120EM, BF125EM, BF145EM

READ AND SAVE THESE INSTRUCTIONS

READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.

PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH

INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

GENERAL SAFETY INFORMATION

When using electrical appliances, basic precautions should always be followed to reduce

the risk of fire, electric shock and injury to person, including the following:

1. Read all instructions before installing or using exhaust fan.

2. Use this unit only in the manner intended by the manufacturer.

If you have questions, contact the manufacturer.

3. Before servicing or cleaning the unit, switch power off at

service panel and lock the service disconnecting means to

prevent power from being switched on accidentally. When the

service disconnecting means cannot be locked, securely fasten

a prominent warning device, such as a tag, to the service

panel.

SAVE THESE INSTRUCTIONS

IMPORTANT INSTRUCTIONS -

OPERATING MANUAL

4. Installation work and electrical wiring must be done by qualified

person(s) in accordance with all applicable codes and

standards, including fire-related construction.

5. Sufficient air is needed for proper combustion and exhausting

of gases through the flue (chimney) of fuel burning equipment to

prevent back drafting. Follow the heating equipment

manufacturer’s guideline and safety standards such as those

published by the National Fire Protection Association (NFPA)

and the American Society for Heating, Refrigeration, and Air

Conditioning Engineers (ASHRAE), and the local code authorities.

1 of 4

www.geelectrical.com

210572119 Rev. D 1-08

GENERAL SAFETY INFORMATION

(Continued)

CAUTION: FOR GENERAL VENTILATING USE ONLY. DO NOT

USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS AND

VAPORS.

6. When cutting or drilling into wall or ceiling, do not damage electrical

wiring and other hidden utilities.

7. Ducted fans must always be vented to the outdoors.

8. This unit must be grounded.

9. To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc. off power unit.

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

DO NOT USE THIS FAN WITH ANY SOLID-STATE SPEED CONTROL DEVICE.

10. Acceptable for use over a bathtub or shower when installed in a

GFCI protected branch circuit.

11. NEVER place a switch where it can be reached from a tub or shower.

WARNING: DO NOT USE IN KITCHENS

INSTALLATION INSTRUCTIONS

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE

PANEL BEFORE STARTING INSTALLATION.

SECTION 1

Preparing the Exhaust Fan

1. Unpack fan from the carton and confirm that all pieces are present.

In addition to the exhaust fan you should have:

1 - Grill

1 - Damper Assembly (attached)

1 - Mounting Bracket

1 - Hardware Bag

1 - Electrical Connector

3 - Wire Nuts

1 - Instruction/Safety Sheet

2. Remove the wire compartment cover and store in the carton until

needed so it does not get damaged or lost (Figure 1).

3. Choose the location for your fan. To

ensure the best air and sound

performance, it is recommended that

the length of ducting and the number

of elbows be kept to a minimum, and

that insulated hard ducting be used.

Larger duct sizes will reduce noise and

airflow restrictions.

4. Select the most convenient electrical

knockout and remove using a straight-

blade screw driver (Figure 2).

SECTION 2

New Construction

1. Using the gauge on the mounting bracket, line up the bracket on

the joist so the bottom of the fan will be flush with the finished

ceiling. Nail or screw the bracket in place securely (Figure 3).

2. Snap the fan body into the bracket (Figure 4). The fan can be

snapped into position with the duct collar facing to the left or the

right depending which is most convenient.

SECTION 3

Existing Construction

1. Position housing against the joist or stud and trace an outline of

the housing onto the ceiling/wall material. Set housing aside and

cut opening, being careful not to cut or damage any electrical or

other hidden utilities (Figure 5).

2. Line up the bracket on the joist so the bottom of the fan will be

flush with the finished ceiling. Nail or screw the snap-in bracket

in place securely (Figure 3).

3. Snap the fan body into the bracket (Figure 4). The fan can be

snapped into position with the duct collar facing to the left or the

right depending which is most convenient.

SECTION 4

Ducting

Figure 1

Figure 2

1/2"

3/4"

Figure 3

Figure 4

Figure 5

2 of 4

www.geelectrical.com

210572119 Rev. D 1-08

CAUTION: ALL DUCTING MUST COMPLY WITH LOCAL AND

NATIONAL BUILDING CODES.

1. Connect the ducting to the fan’s duct collar (Figure 5). Secure in

place using tape or screw clamp. Always duct the fan to the

outside through a wall or roof cap.

SECTION 5

Wiring

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE

PANEL BEFORE STARTING INSTALLATION.

CAUTION: ALL ELECTRICAL CONNECTIONS MUST BE MADE

IN ACCORDANCE WITH LOCAL CODES, ORDINANCES, OR NATIONAL

ELECTRICAL CODE. IF YOU ARE UNFAMILIAR WITH METHODS OF

INSTALLING ELECTRICAL WIRING, SECURE THE SERVICES OF A

QUALIFIED ELECTRICIAN.

1. Run wiring from an approved wall switch carrying the appropriate

rating. One neutral (white), one ground (green or bare copper), and

one hot (black lead connected to the switch). Secure the electrical

wires to the housing with an approved electrical connector. Make

sure you leave enough wiring in the box to make the connection to

the fan’s receptacle.

2. From where you have access to inside the fan’s junction box,

connect the White wire from the house to the White wire from

the fan’s receptacle. Connect the Black wire from the wall switch

to the Black wire from the fan’s receptacle. Connect the ground

wire from the house to the Green wire from the fan’s receptacle

(Figure 7). Use approved methods for all connections.

SECTION 6

Completing the Installation

1. Reinstall the fan’s wire compartment cover. Rotate the blower wheel

by hand to ensure it spins freely. Plug the fan’s quick connect motor

cord into the receptacle. This cord will only fit one way into the

receptacle (Figure 8).3. Restore power and test your installation.

2. Install the grill by squeezing the two ends of the springs together

and installing them up into the slots of the fan’s housing. Push the

grill up into position (Figure 9).

3. Restore power and test your installation.

SECTION 7

Use and Care

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE

PANEL BEFORE SERVICING THE UNIT.

1. Cleaning the Grill: Remove grill and use a mild detergent, such

as dishwashing liquid, and dry with a soft cloth. NEVER USE ANY

ABRASIVE PADS OR SCOURING POWDERS. Completely dry grill

before reinstalling. Refer to instructions in Section 6

Finishing the

Installation

, to reinstall grill.

2. Cleaning the Fan Assembly: Unplug the motor cord from receptacle.

Wipe all parts with a dry cloth or gently vacuum the fan. NEVER

IMMERSE ELECTRICAL PARTS IN WATER. Plug the motor cord

back in and restore power.

Troubleshooting Guide

Trouble Probable Cause Suggested Remedy

1. Fan does not operate when the switch is on. 1a. A fuse may be blown or a circuit tripped. 1a. Replace fuse or reset circuit breaker.

1b. Connector plug from motor is not plugged in. 1b. Turn off power to unit. Remove Grill and plug motor into

receptacle in housing. Restore power to unit.

1c. Wiring is not connected properly. 1c. Turn off power to unit. Check that all wires are connected.

2. Fan is operating, but air moves slower than normal. 2. Obstruction in the exhaust ducting. 2. Check for any obstructions in the ducting. The most common

are bird nests in the roof cap or wall cap where the fan

exhausts to the outside.

3. Fan is operating louder than normal. 3a. Motor is loose. 3a. Turn off power to unit. Remove grill and check that all screws

are fully tightened. Restore power to unit.

3b. Fan blade is hitting housing of unit. 3b. Call your dealer for service.

Figure 6

Figure 7 Ground

Supply

from

house

White

Hot (Black)

Figure 8

Figure 9

3 of 4

www.geelectrical.com

WARRANTY

WHAT IS COVERED?

Full Five Year Parts Warranty from date of original proof of purchase. We will

provide, free of charge, a replacement part that fails due to manufacturing

defect in material or workmanship, when installed and used as directed in

the User’s Guide.

This warranty is extended to the original purchaser for products purchased

for ordinary home use.

GE Bath Fan Hot Line

1-800-684-9975

FOR TECHNICAL ASSISTANCE

AND / OR QUESTIONS.

Read your User’s Guide. If you have any questions about operating the product, please contact your dealer.

Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages and some states do not allow limitations on how

long an implied warranty lasts, so these exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may have other

rights which vary from state to state and province to province.

WHAT IS NOT COVERED?

• Installation services or service trips to your home to teach you how to use

the product.

• Labor costs or the cost of replacement components as part of routine

maintenance.

• Failure or defects in product arising from Improper installation

If you have an installation problem, contact your dealer or installer. You are

responsible for providing adequate electrical, exhausting and other connecting

facilities. See the Installation Instructions provided with this product for

electrical, exhaust and connection details.

• Replacement of house fuses or resetting of circuit breakers.

• Failure of the product if it is used for something other than the intended

purpose of manufacturer or used commercially.

• Damage to the product caused by accident, fire, floods, acts of customer,

or acts of God.

This warranty contains the sole and exclusive warranty of GE for claims based on defects in these products. Upon the expiration of the warranty period, all

such liability shall terminate. There are no other warranties, whether written, oral, implied or statutory. NO IMPLIED STATUTORY WARRANTY OF MERCHANTABILITY

OR FITNESS FOR PARTICULAR PURPOSE SHALL APPLY.