GE UVD6301S Original instructions

Write the model and serial
numbers here:
Model #_________________
Serial # _________________
These numbers are also found on
the Product Property Registration
Card sent separately with your
downdraft ventilation system and
on the label located on the front
panel of the unit.
ESPAÑOL
Para consultar una version en
español de este manual de
instrucciones, visite nuestro sitio de
internet GEAppliances.com.
VENT SYSTEM
Downdraft
49-2000733 Rev. 1 09-20 GEA
SAFETY INFORMATION ...........3
USING THE HOOD
Downdraft Vent System ..................5
CARE AND CLEANING
Downdraft Vent System ..................6
INSTALLATION INSTRUCTIONS ..7
TROUBLESHOOTING TIPS........ 16
LIMITED WARRANTY ............. 17
ACCESSORIES ..................... 18
CONSUMER SUPPORT ............20
UVD6301S
UVD6361S
OWNER’S MANUAL &
INSTALLATION
INSTRUCTIONS
GE is a trademark of the General Electric Company. Manufactured under trademark license.

249-2000733 Rev. 1
THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.
Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.
We take pride in the craftsmanship, innovation and design that goes into every GE Appliances
product, and we think you will too. Among other things, registration of your appliance ensures that we
can deliver important product information and warranty details when you need them.
Register your GE appliance now online. Helpful websites and phone numbers are available in the
Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration
card included in the packing material.

49-2000733 Rev. 1 3
SAFETY INFORMATION
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING
READ AND SAVE THESE INSTRUCTIONS
WARNING TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
A. Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
B. Before servicing or cleaning unit, switch power off
at service panel and lock the service disconnecting
means to prevent power from being switched
on accidentally. When the service disconnecting
means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the
service panel.
C. Do not use this unit with any solid-state speed
control device.
D. Plug your vent system into a 120-volt grounded
outlet only. Do not remove the round grounding
prong from the plug. If in doubt about the
grounding of the home electrical system, it is your
responsibility and obligation to have an ungrounded
outlet replaced with a properly grounded, three
prong outlet in accordance with the National
Electrical Code. Do not use an extension cord with
this appliance.
CAUTION FOR GENERAL VENTILATING USE
ONLY. DO NOT USE TO EXHAUST HAZARDOUS
OR EXPLOSIVE MATERIALS AND VAPORS.
WARNING TO REDUCE THE RISK OF INJURY
TO PERSONS IN THE EVENT OF A RANGE TOP
GREASE FIRE, OBSERVE THE FOLLOWING*:
A. SMOTHER FLAMES with a close-fitting lid, cookie
sheet or metal tray, then turn off the burner. BE
CAREFUL TO PREVENT BURNS. If the flames do
not go out immediately, EVACUATE AND CALL
THE FIRE DEPARTMENT.
B. NEVER PICK UP A FLAMING PAN—You may be
burned.
C. DO NOT USE WATER, including wet dishcloths or
towels—a violent steam explosion will result.
D. Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher,
and you already know how to operate it.
2. The fire is small and contained in the area where
it started.
3. The fire department is being called.
4. You can fight the fire with your back to an exit.
*Based on “Kitchen Fire Safety” published by NFPA.
WARNING TO REDUCE THE RISK OF A
RANGE TOP GREASE FIRE:
A. Never leave surface units unattended at high
settings. Boilovers cause smoking and greasy
spillovers that may ignite. Heat oils slowly on
medium settings.
B. Always turn hood ON when cooking at high heat or
when flambéing food (i.e. Crepes Suzette, Cherries
Jubilee, Peppercorn Beef Flambé).
C. Clean ventilating fans frequently. Grease should not
be allowed to accumulate on fan or filter.
D. Use proper pan size. Always use cookware
appropriate for the size of the surface element.
If You Need Service…
Do not attempt to repair or replace any part of the
vent system unless it is specifically recommended in
this manual. All other servicing should be referred to a
qualified technician.
Be sure electrical power is off before servicing the unit.
It may be necessary to remove the vent system blower
system in order to service components such as the
blower motor or air vent mechanism.
Disconnect power to the cooktop and remove it first.
Reverse the steps in the Install Downdraft Vent section
in the Installation Instructions to remove the blower.
Service parts are available from a GE Appliances
Service and Parts Center.
Make sure all fingers are away from the top of the vent
system when it is lowered.

449-2000733 Rev. 1
SAFETY INFORMATION
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING
READ AND SAVE THESE INSTRUCTIONS
How to Remove Protective Shipping Film and Packaging Tape
Carefully grasp a corner of the protective shipping film
with your fingers and slowly peel it from the appliance
surface. Do not use any sharp items to remove the film.
Remove all of the film before using the appliance for the
first time.
To assure no damage is done to the finish of the
product, the safest way to remove the adhesive from
packaging tape on new appliances is an application of
a household liquid dishwashing detergent. Apply with a
soft cloth and allow to soak.
NOTE: The adhesive must be removed from all parts. It
cannot be removed if it is baked on.
ATTENTION: Please remove the bubble wrap inserted
inside of exhaust before installation. Make sure nothing
is left inside the blower box.
Bubble Wrap

49-2000733 Rev. 1 5
Downdraft Vent System
USING THE VENT SYSTEM: Downdraft Vent System
When Using The Vent System
CAUTION Be careful when raising or lowering
the vent. Be sure pots, pot handles and other objects are
clear of the vent and cannot be struck or tipped by the
vent being raised.
NOTE: There is a slight trim overhang on each side of
the vent.
Ŷ 7RDYRLGLQMXU\EHVXUHILQJHUVDUHFOHDURIWKHYHQW
cover when it is being lowered.
Ŷ .HHSKDQGVDQGILQJHUVDZD\IURPDOOYHQWSDUWV
IMPORTANT: If the vent is obstructed by an object while
it is being raised or lowered, it will stop. Carefully remove
the obstruction and the vent will drop to the lowered
position. Press the button again to return to normal
functons.
To Use The Downdraft System
To raise the downdraft vent, press the button on the top
cover. The vent will rise. The blower can be turned ON or OFF and the speed can be adjusted with
the recessed knob on the right side of
the air vent. The blower, if left on, will
automatically turn off when the vent is
lowered.
NOTE: For most convenient operation, set the blower to
the speed you use most often. The blower will come on
to this speed whenever the unit is raised.
Lower the downdraft vent by
pressing the button on the top
cover. The vent will go down an
the blower will shut off.
Cooking Tips
The high air movement of this vent system can increase
the cooking times for some foods. It may take longer to
reach high cooking temperatures if the vent system is
turned to high right away. Adjust the fan speed for best
cooking results.
For best results when heating oil for deep frying or when
boiling water, use the front surface units or wait until the
water is boiling or the oil is at frying temperatures before
turning on the vent system.
The vent system may not completely capture all the
steam from pans on the front burners.
Button

649-2000733 Rev. 1
CARE AND CLEANING: Downdraft Vent System
Downdraft Vent System
Painted Or Stainless Steel Surfaces
Do not use a steel wool pad; it will scratch the surface.
To clean the stainless steel surface, use warm, sudsy
water or a stainless steel cleaner or polish. Always wipe
the surface in the direction of the grain. Follow the cleaner
instructions for cleaning the stainless steel surface.
For difficult stains on stainless steel, use a cleaner that
contains lactic acid or citric acid.
To inquire about purchasing cleaning products including
stainless steel appliance cleaner or polish read the
Assistance and Accessories sections at the beginning of
this manual.
Grease Filters
The efficiency of your vent system depends on a clean
filter. Frequency of cleaning depends on the type of
cooking you do. Grease filters should be cleaned at least
once a month. Never operate the vent system without
the filters in place.
To remove: Remove filters from the air vent by reaching
the filters through the vent openings, pushing down then
pulling out. NOTE: The filters are different sizes. Be sure
to replace them as removed, wider one on the left
To clean: Soak and then agitate in a hot detergent
solution. Light brushing may be used to remove
embedded soil. Rinse, shake and remove moisture
before replacing. Do not clean the filters in the
dishwasher.
With careful handling, the filter will last for years. If
replacement becomes necessary, order the part from
your dealer.
Filter Tabs

49-2000733 Rev. 1 7
Installation
Instructions
“If you have questions, call GE Appliances at 800.GE.CARES (800.432.2737)
or visit our website at: GEAppliances.com”
INSTALLATION INSTRUCTIONS
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
•IMPORTANT— Save these
instructions for local inspector’s use.
•IMPORTANT— Observe all governing
codes and ordinances.
•Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these instructions for
future reference.
• Skill level – Installation of this vent hood requires
basic mechanical and electrical skills.
• Proper installation is the responsibility of the
installer.
• Product failure due to improper installation is not
covered under the Warranty.
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of
an electrical short circuit, grounding reduces the risk
of electric shock by providing an escape wire for
the electric current. This appliance is equipped with
a cord having a grounding wire with a grounding
plug. The plug must be plugged into an outlet that is
property installed and grounded.
WARNING
Improper grounding can result in a risk of electric
shock.
Consult a qualified electrician if the grounding
instructions are not completely understood, or if
doubt exist as to whether the appliance is properly
grounded.
Do not use an extension cord. If the power supply
cord is too short, have a qualified electrician install
an outlet near the appliance.
If you received a damaged vent system, you should
contact your dealer.
Downdraft Vent Systems
UVD6301S, UVD6361S
PARTS SUPPLIED
Open the carton and remove parts package.
Check contents to be sure all pieces are
present.
REMOVE PACKAGING
Remove the shipping materials and the carton;
set carton aside. The carton can be used as a
pad when changing or adjusting vent direction.
TOOLSANDMATERIALSREQUIRED
•Safety glasses
• Large flat-blade screwdriver
• Jigsaw
• Carpenter’s square
• Ductwork to suit the installation
• Level
Stabilizing Brackets
Qty:2
Filters - inside unit
Qty:2
Countertop Mounting
Screw, 1/4-20 x 2.00
Hex Hd
Qty:2
Plastic Template (attached
to product) Qty:1
Downdraft
Leveling Screw,
1/4-20 x .50 Hex
Hd - Qty:2
Wood Screw, #8 x
.750 SI Round Hd
- Qty:4
28.5” for 30” Models
34” for 36” Models

849-2000733 Rev. 1
Safety Information
INSTALLATION INSTRUCTIONS
WARNING TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
Ɣ,QVWDOODWLRQZRUNDQGHOHFWULFDOZLULQJPXVWEH
done by qualified person(s) in accordance with all
applicable codes and standards, including fire-rated
construction.
Ɣ6XIILFLHQWDLULVQHHGHGIRUSURSHUFRPEXVWLRQDQG
exhausting of gases through the flue (chimney) of
fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer’s
guidelines and safety standards such as those
published by the National Fire Protection Association
(NFPA), the American Society for Heating,
Refrigeration and Air Conditioning Engineers
(ASHRAE) and the local code authorities.
Ɣ:KHQFXWWLQJRUGULOOLQJLQWRZDOORUFHLOLQJGRQRW
damage electrical wiring and other hidden utilities.
Ɣ'XFWHGIDQVPXVWDOZD\VEHYHQWHGWRWKHRXWGRRUV
CAUTION TO REDUCE THE RISK OF FIRE
AND TO PROPERLY EXHAUST AIR, BE SURE TO
DUCT AIR OUTDOORS. DO NOT VENT EXHAUST
AIR INTO SPACES WITHIN WALLS OR CEILINGS
OR INTO ATTICS, CRAWL SPACES OR GARAGES.
WARNING TO REDUCE THE RISK OF FIRE,
USE ONLY METAL DUCT WORK.
Ɣ:KHQDSSOLFDEOHLQVWDOODQ\PDNHXSUHSODFHPHQW
air system in accordance with local building code
requirements. Visit GEAppliances.com for available
makeup air solutions.
Ɣ39&VHZHUSLSHFDQEHXVHGDVGXFWXQGHUFRQFUHWH
slab if allowed by local code board.

49-2000733 Rev. 1 9
Installation Preparation
INSTALLATION INSTRUCTIONS
POWER SUPPLY
This downdraft vent must be supplied with 120V, 60
Hz. and connected to an individual, properly grounded
branch circuit, protected by a 15- or 20-ampere circuit
breaker or time-delay fuse.
A properly grounded 3-prong receptacle should be
located within reach of the vent’s two-foot power cord.
• Gas Cooktops
If this vent is installed in combination with a GE or
Monogram gas cooktop, it may operate from the same
duplex outlet.
• Electric Cooktops
If this vent is installed in combination with a GE or
Monogram electric cooktop, the vent must operate
from a separate 120V outlet.
Locate the receptacle inside the cabinet on the right side
wall (see illustration). The receptacle cannot be placed
on the back of the cabinet wall where it may interfere
with the downdraft plenum.
The downdraft vent power cord is to be routed beneath
the cooktop and routed away from heat generated by the
cooktop.
Ensure that the cooktop is installed per manufacturer’s
installation instructions.
IMPORTANT
(Please read carefully)
The power cord of this appliance is equipped with
a three-prong (grounding) plug which mates with a
standard three-prong grounding wall receptacle to
minimize the possibility of electric shock. The customer
should have the wall receptacle and circuit checked by
a qualified electrician to make sure the receptacle is
properly grounded and has correct polarity.
• Where a standard two-prong wall receptacle is
encountered, it is the personal responsibility and
obligation of the customer to have it replaced with a
properly grounded three-prong wall receptacle.
Do not, under any circumstances, cut or remove the
third (ground) prong from the power cord.
Do not use an extension cord or adapter plug with this
appliance. Follow National Electrical Code or prevailing
local codes and ordinances.
Location of Rating Label: on front of chassis of vent
system.
VOLTS AMPS DUCT
120 4.0 3-1/4 X 10
SPECIFICATIONS
DO NOT Locate
Gas or Electrical
Connections within
this Area
34"(cutout width) for 36" models
28-1/2" (cutout width) for 30" models
29-1/2"
12"
Electrical
Outlet 12"
Above
Cabinet
Floor
Locate the gas or electrical
connection only within the
shaded area.

10 49-2000733 Rev. 1
Installation Preparation
INSTALLATION INSTRUCTIONS
PRODUCT DIMENSIONS
AB
30” Models 30” 26-1/4”
36” Models 36” 32-1/4”
A
B
22.3”
2”
2-1/2”
7”
7-1/4”
36-1/2”

49-2000733 Rev. 1 11
INSTALLATION INSTRUCTIONS
Installation Preparation
PREPARING FOR INSTALLATION
• Unpack the cooktop and read the Installation
Instructions to understand the required countertop
cutout dimensions and location in the countertop,
the cooktop spacing to the front edge of the
countertop, and the required clearances to the
cabinets and walls. The vent system required cutout
width is shown on page 9. Confirm there is enough
side to side counter space to meet the required
spacing and clearances for the cooktop.
• Using the illustrations below and taking
measurements of the cooktop to establish dimension
A, confirm there is enough front to back counter
space (dimension B) to fit both the cooktop and the
vent system. Note the cooktop rear edge will overlap
the vent system front surface (refer to Page 10).
• Refer to the Creative Solutions section on page 13 if
more counter space is needed.
• Using the illustrations on pages 9 through 12 and
taking measurements of the vent system and its
exhaust vent location, confirm the clearances
needed within the cabinet, the exhaust vent
direction, and the alignment of the exhaust vent with
the ducting. If needed for clearance or duct hookup
alignment, reposition the location of the cooktop, or
modify the cabinetry, or modify the ducting.
• Confirm the electrical receptacles and gas lines are
correctly located, and relocate if needed.
B
C
B is the minimum dimension of the
flat portion of countertop that is needed
A
A is the dimension from the screw head on the front surface of
the cooktop base to the rear edge of the cooktop. If you cannot find dimension A
in the cooktop installations instructions, then you must measure it.
Depth of cutout is A + 2 1/8”
Minimum counter depth B = A + C + 2.5"
Dimension C is defined in cooktop Installation Instruction
COOKTOP
1/8” minimum
Front edge
of countertop
Front of cutout
in countertop
Screw head
Front
edge
of
cooktop
Front of cutout
in countertop
Back edge
of cooktop
Back of cut
in countertop
2 1/8”
3/8”
minimum
D
o
w
n
d
r
a
f
t
V
e
n
t
Counter Top
Gear Motor
Cover
Blower Box
Cook Top Chimney Top
Air Vent
120 Vac
Grounded
Outlet
3-1/4" x 10"
Duct Connector

12 49-2000733 Rev. 1
Installation Preparation
INSTALLATION INSTRUCTIONS
VENTING OPTIONS
•The downdraft vent is shipped with the discharge
outlet pointing straight down and can be changed to
the left or right side. To avoid interference problems,
the downdraft vent cannot be vented to the right
when installed with a GE or Monogram gas cooktop,
or with a GE or Monogram non-induction electric
cooktop.
•The blower outlet is sized for 3-1/4” x 10” and can
be transitioned to 6” round.
The blower is shipped with its discharge facing
DOWN. Follow these steps ONLY if:
•the position of the blower discharge needs to be
moved so ductwork does not interfere with floor
joists, plumbing or wiring below.
•it is necessary to rotate the blower discharge to the
RIGHT or LEFT.
Place the unit on its back on
a table or work surface.
Pull out the bubble wrap
sheet. Make sure nothing is
left inside.
DOWN DISCHARGE - MOVING BLOWER LEFT OR
RIGHT
1. Loosen the 4 nuts and 2 clamp channels.
2. Remove the 5 screws on the bottom. These 5
screws are for shipping and do not need to be
re-tightened.
3. Slide blower to desired position.
4. Use supplied cover plate to close open space (if
any).
5. Tighten wing nuts to secure top of blower and use
sheet metal screws through bottom flange to secure
bottom of blower.
LEFT OR RIGHT DISCHARGE
1. Remove the 4 nuts and 2 clamp channels.
2. Remove the 5 screws on the bottom. These 5
screws are for shipping and do not need to be
re-tightened.
3. Carefully lift blower and disconnect motor plug if
necessary. Reposition blower and RECONNECT
MOTOR PLUG.
4. Use supplied cover plate to close open space (if
any).
5. Replace clamp channels and use nuts to secure the
blower in its new position.
6. Use sheet metal screws through bottom flange to
secure bottom of blower.
For best performance: Choose the ducting option
which allows the shortest length of ductwork and a
minimum number of elbows and transitions. Check
location of floor joists, wall studs, electrical wiring or
plumbing for possible interference.
NOTE: The unit is shipped with the 3-1/4" x 10"
discharge facing DOWN. See “CHANGING BLOWER
DIRECTION” on page 3, if necessary.
The system will operate most efficiently when the
ductwork does not exceed 40 feet of equivalent duct.
The chart, below, shows equivalent feet of elbows and
transitions. The number of feet of straight duct plus the
equivalent feet of transitions and/or elbows to be used
should equal 40 feet or less.
Nut Blower
Motor Plug
Sheet
Metal
Screw
Cover Plate
Clamp
Channel
Nuts
Blower
Clamp
Channel
Sheet Metal
Screws
Bottom
Flange
6" Round
Elbow 3-1/4"x10" to 6" Round Transition 3-1/4"x10" 90°Elbow
equals 6 ft. of
straight duct equals 2 ft. of straight duct equals 8 ft. of straight duct
Bubble
Wrap Sheet

49-2000733 Rev. 1 13
INSTALLATION INSTRUCTIONS
Design Information
CREATIVE SOLUTIONS
•When the kitchen
design calls for an
against-the-wall
installation, move
the base cabinet
forward 3” to 5”.
Filler panels or
complementary
moldings can be
added to exposed
cabinet sides.
•In an island or
peninsula, use
an extra-deep
countertop.
The countertop
overhang at the
front can be
adjusted to meet
setback to cutout
requirements.
•When the cutout
to the front edge of the countertop requirement is
more than 2”, add a bullnose trim to the front edge
of the countertop. Include the trim thickness when
measuring the front edge to cutout requirement. By
adding the trim, the cooktop can be moved forward,
providing additional countertop depth and interior
cabinet space.
•When the distances between the vent and the
inside cabinet side walls are more than 5-1/2” and/
or the inside cabinet back wall is more than 4-1/2”,
false walls should be constructed inside the cabinet
for securing the vent with the stabilizing brackets
(refer to Cutouts and Clearances under Installation
Preparation.)
PREPARING THE COUNTERTOP
Lay out and cut the cooktop cut-out far enough
FORWARD so downdraft will fit behind it.
1. Set cooktop in place and
slide it as far forward as
possible. Center and square
it with edges or countertop.
2. Place the plastic template
against the back flange of
the cooktop and center it.
Trace around template to
mark the downdraft opening.
3. Remove cooktop from countertop.
4. Cut downdraft opening. Be careful not to chip edges
of countertop.
Cover Panel
End
Panel
Countertop
Overhang
per Cooktop
Clearances
Must be
Maintained
Base
Cabinet
Filler Panel Base Sink
Filler Panel
Maintain Cutout Clearances
to Front Edge as Specified

14 49-2000733 Rev. 1
PREPARE FOR DUCTWORK
Determine the best route for ductwork; it can be routed
in a variety of ways depending on the kitchen layout.
IMPORTANT: The downdraft air discharge outlet
IRUWKLVXQLWLV»´[´UHFWDQJXODU3ODQGXFWLQJ
accordingly.
Typical duct arrangement countertop series.
To maximize the ventilation performance of the vent
system:
1. Minimize the duct run length and number of
transitions and elbows.
2. Maintain a constant duct size.
3. Seal all joints with duct tape to prevent any leaks.
4. Do not use any type of flexible ducting.
Design Information
INSTALLATION INSTRUCTIONS
Inside wall
cabinet
Up inside wall to roof or
overhang Directly to outside
Between floor joists Through cabinet toe space
Peninsula or island Peninsula
Outside
wall cabinet
NOTE: PVC sewer pipe type PSM 12454-B
Schedule 40 ASTM D1785.
Wall Cap Concrete
Slab
6" (15 cm)
Dia. PVC
Sewer Pipe
6" (15 cm)
Dia. Metal
Duct
Pack tightly with gravel
or sand completely
around pipe
3-1/4" x 10" Rectangular
to 6" Round Transition
6" (15 cm)
Dia. 90
Metal Elbow
6" (15 cm) Dia.
Metal Duct
16"
(40.6 cm)
Max.
12"
(30 cm)
Min.
6"
(15 cm)
Dia. PVC
Coupling
6" (15 cm) Dia.
PVC Sewer Pipe
Elbow
6" (15 cm) Dia.
PVC Sewer Pipe
Elbow
6" (15 cm)
Dia. PVC
Sewer
Pipe
6"
(15 cm)
Dia.
PVC
Coupling
30'-0" (9.14 m) Max.
Optional duct arrangement under concrete
slab. PVC duct should be used if installing
under a poured concrete slab.
Install ductwork so the piece of duct nearest the
downdraft unit slots INTO the next piece of the duct.
Secure the joints with self-tapping screws and apply
duct tape around the joints to ensure an airtight seal.
Duct Tape
Over Seam and Screw
Screw
Air
Flow
Left
Discharge
Right
Discharge
Down
Discharge
(as shipped)

49-2000733 Rev. 1 15
1MOUNT THE UNIT
ASet downdraft into opening. Extend leveling
brackets to floor of cabinet so downdraft sits
straight. (NOTE: Leveling brackets can be
removed and re-attached in other positions.
Bottom flange may have to face inward in tight
cabinet installations.)
BSecure the downdraft to the countertop as
follows: Hold the downdraft against the back of
countertop cut-out and tighten the 2 mounting
screws (one on each end of unit) on underside
of countertop. Use a shim between screw and
underside of granite countertops.
The ends of the template may be broken or cut
and used as shims if required.
INSTALLATION INSTRUCTIONS
Installation Instructions
2CONNECT POWER
Plug power cord into properly grounded receptacle.
1MOUNT THE UNIT (Cont.)
CScrew leveling brackets to bottom of cabinet
using the four wood screws (provided with the
unit) on each side.
DTighten leveling screws through leveling
bracket slots to the unit on each side.
EPlace cooktop into the countertop cutout. There
should be 1/8" minimum gap between the front
of the vent trim and the rear of the cooktop.
FConnect duct. Use a roof or wall cap (with
damper) that is intended for use with kitchen
hoods and vent systems.
3INSTALL FILTERS, CHECK
OPERATION
• Press the button on the top cover to raise the
vent.
• Lift the vent straight up and pull forward.
• Slide filter into the retainers and close the vent.
• Turn the knob on the right side of the air vent to
start the blower and adjust the speed.
• To lower the vent, press the button on the top
cover.
NOTE: It is not necessary to turn the fan OFF
before lowering the vent. The fan will automatically
turn off when the vent is lowered. When the fan
is not turned off before lowering the vent, it will
automatically come on at the previously set speed
when the vent is fully raised.
Leveling Bracket -
Flange Facing Out Mounting Screws
Leveling
Screw
Leveling
Screw
Wood
Screws
Leveling Bracket -
Flange Facing In
Break/Cut the Ends
Bracket
Mounting Screw
Shim
Countertop

16 49-2000733 Rev. 1
TROUBLESHOOTING TIPS
TROUBLESHOOTING TIPS
Save time and money! Review the charts on the following pages first and you may not need to call for service.
Problem Possible Cause What To Do
Fan does not work The vent is not fully extended. Press the button on the top cover.
Vent does not work The vent is not plugged into an outlet. Plug the vent into a 120V power outlet.
The button did not engage the lift
motor. Hold down the button for a couple of seconds to activate the motor.
The circuit breaker may have tripped. Check the circuit breaker— reset if necessary.
Sufficient makeup (replacement) air is
required for exhausting appliances to
operate to rating.
Check with local building codes, which may
require or strongly advise the use of makeup
air. Visit GEAppliances.com for available
makeup air solutions.

49-2000733 Rev. 1 17
LIMITED WARRANTY Staple your receipt here. Proof of the original purchase
date is needed to obtain service under the warranty.
GEAppliances.com
All warranty service is provided by our Factory Service Centers, or an authorized Customer Care®technician. To schedule
service online, visit us at GEAppliances.com/service, or call GE Appliances at 800.GE.CARES (800.432.2737). Please
have your serial number and your model number available when calling for service.
Servicing your appliance may require the use of the onboard data port for diagnostics. This gives a GEAppliances factory
service technician the ability to quickly diagnose any issues with your appliance and helps GE Appliances improve its
products by providing GE Appliances with information on your appliance. If you do not want your appliance data to be
sent to GE Appliances, please advise your technician not to submit the data to GE Appliances at the time of service.
What GE Appliances will not cover:
ŶService trips to your home to teach you how to use
the product.
ŶImproper installation, delivery, or maintenance.
ŶFailure of the product if it is abused, misused,
modified, or used for other than the intended purpose
or used commercially.
ŶReplacement of house fuses or resetting of circuit
breakers.
ŶDamage to the product caused by accident, fire,
floods, or acts of God.
ŶIncidental or consequential damage caused by
possible defects with this appliance.
ŶDamage caused after delivery.
ŶProduct not accessible to provide required service.
ŶService to repair or replace light bulbs, except for LED
lamps.
GE Appliances Limited Warranty
EXCLUSION OF IMPLIED WARRANTIES
Your sole and exclusive remedy is product repair as provided in this Limited Warranty. Any implied warranties,
including the implied warranties of merchantability or fitness for a particular purpose, are limited to one year or
the shortest period allowed by law.
For the period of GE Appliances will replace
One year
From the date
of the original
purchase
Any part of the cooking product which fails due to a defect in materials or workmanship.
During this limited one-year warranty, GE Appliances will provide, free of charge, all labor
and related service costs to replace the defective part.
If you received a damaged downdraft vent system
Immediately contact the dealer (or builder) that sold you the downdraft vent system.
This limited warranty is extended to the original purchaser and any succeeding owner for products purchased for
home use within the USA. If the product is located in an area where service by a GE Appliances Authorized Servicer
is not available, you may be responsible for a trip charge or you may be required to bring the product to an Authorized
GE Appliances Service location for service. In Alaska, the limited warranty excludes the cost of shipping or service
calls to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This limited warranty
gives you specific legal rights, and you may also have other rights which vary from state to state. To know what your
legal rights are, consult your local or state consumer affairs office or your state’sAttorney General.
Warrantor: GE Appliances, aHaier company
Louisville, KY 40225
Extended Warranties: Purchase a GE Appliances extended warranty and learn about special discounts that are
available while your warranty is still in effect. You can purchase it online anytime at
GEAppliances.com/extended-warranty
or call 800.626.2224 during normal business hours. GE Appliances Service will still be there after your warranty expires.

18 49-2000733 Rev. 1
Looking For Something More?
GE Appliances offers a variety of accessories to
improve your cooking and maintenance experiences!
Refer to the Consumer Support page for phone numbers
and website information.
The following products and more are available:
Accessories
Parts
Black Stainless Steel Trim (30”)
Black Stainless Steel Trim (36”)
Cleaning Supplies
CitruShine™ Stainless Steel Wipes
Stainless Steel Appliance Cleaner
ACCESSORIES

49-2000733 Rev. 1 19
Notes

20 49-2000733 Rev. 1
Consumer Support
CONSUMER SUPPORT
GE Appliances Website
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day, any day
of the year! You can also shop for more great GE Appliances products and take advantage of all our on-line support
services designed for your convenience. In the US: GEAppliances.com
Register Your Appliance
Register your new appliance on-line at your convenience! Timely product registration will allow for enhanced
communication and prompt service under the terms of your warranty, should the need arise. You may also mail in
the pre-printed registration card included in the packing material. In the US: GEAppliances.com/register
Schedule Service
Expert GE Appliances repair service is only one step away from your door. Get on-line and schedule your service at
your convenience any day of the year. In the US: GEAppliances.com/service
or call 800.432.2737 during normal business hours.
Extended Warranties
Purchase a GE Appliances extended warranty and learn about special discounts that are available while your
warranty is still in effect. You can purchase it on-line anytime. GE Appliances Services will still be there after your
warranty expires. In the US: GEAppliances.com/extended-warranty
or call 800.626.2224 during normal business hours.
Remote Connectivity
For assistance with wireless network connectivity (for models with remote enable),
visit our website at GEAppliances.com/connect or call 800.220.6899 in the US.
Parts and Accessories
Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes
(VISA, MasterCard and Discover cards are accepted). Order on-line today 24 hours every day.
In the US: GEApplianceparts.com or by phone at 877.959.8688 during normal business hours.
Instructions contained in this manual cover procedures to be performed by any user. Other servicing
generally should be referred to qualified service personnel. Caution must be exercised, since improper
servicing may cause unsafe operation.
Contact Us
If you are not satisfied with the service you receive from GE Appliances, contact us on our Website with all the
details including your phone number, or write to:
In the US: General Manager, Customer Relations | GE Appliances, Appliance Park | Louisville, KY 40225
GEAppliances.com/contact