GE Tetra GEPS24W-80M User manual

• Supports Tetra PowerStrip DS, Tetra miniStrip DS, Tetra EdgeStrip,
Tetra Contour and Tetra Contour LS LED lighting systems
• Class 2 wiring per NEC Article 725 (SELV)
• IP66 rated: wet location rated
• M20 Thread
(GEPS24W-80M)
Tetra® LED Systems Power Supply
24
Volt
GE
Lighting Solutions
Installation Guide
imagination at work
Power Supply Features
Power Supply Installation
1
Power supply
Conduit
Power supply
input wires
AC Line
Run AC line through conduit and
attach conduit to outdoor-rated
enclosure. Attach power supply to
enclosure.
3
Brown (-)
Green with
yellow stripe
Blue (+)
Connect the AC line to the brown
(line) and blue (neutral) input wires of
the power supply using 18-14 AWG
(0.82-2.08 mm2) twist-on wire
connectors. Properly ground (green
wire with yellow stripe) power supply
in accordance with National Electric
Code (NEC) Article 600.
Connect the red stripe wire (+) of the
LED strip to the red wire (+) of the
power supply. Connect the white
wire (-) of the LED strip to the black
wire (-) of the power supply.
2
To power supply
Red (+)
Red stripe (+)
White (-) Black (-)
NOTE: All electrical connections
should be made within the letter.
RISK OF ELECTRIC SHOCK:
• Disconnect power at fuse box or circuit breaker before servicing or
installing product.
• Properly ground Tetra® power supply.
RISK OF FIRE:
• Use only approved wire for input/output connection.
Minimum size 18 AWG (0.82 mm2)
• Follow all local codes.
RISQUES DE DÉCHARGES ÉLECTRIQUES
• Coupez l’alimentation électrique à la boîte de fusibles ou au
disjoncteur avant l’entretien ou l’installation du produit.
• Assurez-vous de correctement mettre à terre l’alimentation
électrique Tetra®.
RISQUES D’INCENDIE
• N’utilisez que des ls approuvés pour les entrées/sorties de
connexion. Taille minimum 18 AWG (0.82 mm2).
• Respectez tous les codes locaux.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
WARNING/AVERTISSEMENT

NOTE: Properly ground the power supply and sign in accordance with all local codes.
NOTE: When installing power supply, connect to the appropriate sized building breaker or disconnect device for line and neutral
connections, in accordance with local, state or country regulations.
SIGN098-R012412
Power Supply Specications
4Mount power supply in a horizontal
orientation with a minimum of one
screw per mounting plate (two
screws per power supply).
5Tighten liquid-tight ttings and
properly replace cover on junction
box to ensure a water-tight seal.
Conforms to the following standards:
Supports
Tetra
Products SKUs
Maximum Load
per Power Supply
Remote Mounting Distance
18 AWG/
0.82 mm2
16 AWG/
1.31 mm2
14 AWG/
2.08 mm2
12 AWG/
3.31 mm2
Tetra
PowerStrip DS
GEWHDSPS6, GEWWDSPS6-50K,
GEWWDSPS6-41K, GEWWDSPS6
12 modules/
16.5 ft. (5.03 m) 20 ft./6.1 m 25 ft./7.6 m 35 ft./10.6 m 40 ft./12.1 m
Tetra
miniStrip DS
GEWHBDP6, GEWWBDP6-50K,
GEWWBDP6-41K, GEWWBDP6
31 modules/
31 ft. (9.45 m) 20 ft./6.1 m 25 ft./7.6 m 35 ft./10.6 m 40 ft./12.1 m
Tetra
EdgeStrip
GEWHBIP2, GEWWBIP2-50K,
GEWWBIP2-41K, GEWWBIP2
30 modules/
30 ft. (9.15 m) 20 ft./6.1 m 25 ft./7.6 m 35 ft./10.6 m 40 ft./12.1 m
Tetra
Contour LS
GEWHXNLA2-WH, GEBLXNLA2-BL, GEGLXNLA2-GL,
GERDXNLA2-RD, GEWHXNAA2-WH, GEBLXNAA2-BL,
GEGLXNAA2-GL, GERDXNAA2-RD
24 ft. (7.32 m) 30 ft./9.1 m 50 ft./15.2 m 80 ft./24.4 m 120 ft./36.6 m
Tetra Contour GEWHXNLE1, GEWWXNLE1, GEBLXNLE1, GEGLXNLE1,
GERDXNLE1, GERCXNLE1, GEYAXNLE1 24 ft. (7.32 m) 30 ft./9.1 m 50 ft./15.2 m 80 ft./24.4 m 120 ft./36.6 m
* Maximum case temperature is 80°C
Performance Data Min Typical Max
Input Voltage (VAC) 90 100-240 264
Input Frequency (Hz) - 50/60 -
Input Current (A) - - 1.2
Output Voltage (VDC) 23.0 24.3 25.6
Output Current (ADC) 0.6 - 3.3
Output Power (W) - - 80
Environmental Operating Temperature Range -40°C +25°C +60°C*
Environmental Humidity (non-condensing) 0% - 95%
Environmental Storage Temperature Range -40°C - +85°C
Dimensions 12 in. x 2.0 in. x 1.25 in. (307 mm x 52 mm x 32 mm)
GE Lighting Solutions • 1-888-MY-GE-LED • www.gelightingsolutions.com
1 - 8 8 8 - 6 9 - 4 3 - 5 3 3
GE Lighting Solutions, LLC is a subsidiary of the General Electric Company. Tetra is a trademark of GE Lighting Solutions, LLC. The GE brand and logo are trademarks of the General Electric Company.
© 2012 GE Lighting Solutions, LLC. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions.