GE Cync CFIXCNLR4S1 User manual

Wafer Downlight
Installation Guide
4-in & 6-in Integrated LED Recessed Fixture
GE and C by GE is a trademark of General Electric Company. Used under trademark license.

Gettings Started
STEP 1
Download the Cync App, powered
by Savant, on your smartphone
STEP 2
Determine your Wafer Downlight
location and complete installation
STEP 3
Add your Wafer Downlight to the
Cync App
For set up help, visit cyncsupport.gelighting.com
or call 1-844-302-2943
2
*DIRECTLY CONNECT TO AMAZON ALEXA
Complete installation and turn on light.
If Alexa says, “New light found”, you can begin using your light with Alexa.
Otherwise say, “Alexa, discover my devices” and then use Alexa to control your light.

Let’s Do It
INCLUDED SOLD
SEPARATELY
YOU’LL NEED
Hammer LadderFlathead
Screwdriver
Junction Box Integrated
LED Trim
Wire Nuts (3)
3
Drywall Saw or
Hole Saw
(4-1/4” or 6-1/4”
diameter)
Safety
Glasses
Hole Template
Needle
Nose Pliers
Strain Relief

MODEL INPUT VOLTAGE
(Vac, Hz)
CURRENT
(mA)
WATTAGE
(W)
CFIXCNLR4S1
CFIXCNLR6S1
CFIXCNLR4C1
CFIXCNLR6C1
120, 60
120, 60
120, 60
120, 60
110
130
110
130
13
16
13
16
Dimming Capability
NOT FOR USE WITH DIMMER SWITCHES. Compatible with only
CYNC and C by GE smart dimmers that provide dimming at the
switch or through the CYNC App.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
Specifications

Warning
• Risk of fire or electric shock. Installation requires knowledge of
luminaire electrical systems. If not qualified, do not attempt
installation. Minimum 90°C Conductors, if uncertain contact a
qualified electrician.
• To prevent wiring damage or abrasion, do not expose wiring to
edges of sheet metal or other sharp objects.
• These products are intended to be used in dry, damp or wet locations.
• IC rated for direct contact with insulation.
Prepare Electrical Wiring
Electrical Requirements
The LED fixture must be supplied with 120VAC 60Hz
Grounding Instructions
The grounding and bonding of the overall system shall be
done in accordance with National Electric Code(NEC)
Article 410 and local codes.

BEFORE YOU DO ANYTHING:
Turn Off Power
STEP 1
Turn off power source at
the main circuit breaker or
fuse box.
6
ON OFF

Mark the Location on the Ceiling
& Cut the Hole
STEP 2
Determine the position of
your downlight:
• Maximum distance from
junction box to the
downlight is 16 inches.
• Location must be within
range of 2.4GHz Wi-Fi to
enable smart control.
Once determined, use the
hole template to trace the
hole size. Cut the hole using
a drywall or hole saw.
4” wafer requires a 4-1/4
inch hole
6” wafer requires a 6-1/4
inch hole
7

Remove the Knockout
& Wire the Wafer Downlight
STEP 3
Remove the knockout using
a hammer and screwdriver.
Open the junction box cover.
Attach the strain relief (not
included) into the knockout
hole.
Route the wires through the
strain relief.
Connect the wires:
• black to black
• white to white
• green to green or bare
copper wire
Secure the wires with the
three provided wire nuts.
Close the cover of the
junction box.
8

Place Junction Box in the Ceiling
& Install the Fixture
STEP 4
Place the junction box in the ceiling
through the hole.
Connect the light to junction box
using the connector.
Screw the connector together to
complete the connection.
STEP 5
Hold the spring clips against the
fixture and gently guide into the
ceiling until the clips snap into
place.
Complete setup in the Cync App.

Additional Information and Warnings
FCC Compliance Statement Compliance Notice:
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
The device must not be co-located or operating in conjunction with any other
antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.

FCC RF Exposure Statement:
Caution: To maintain compliance with the FCC’s RF exposure guidelines, place the
product at least 20cm from nearby persons.
IC statement
This device complies with RSS247 of Industry Canada. Cet appareil se conforme à
RSS247 de Canada d’Industrie.
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the
device. appareils radio exempts de licence.
Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne
doit pas produire de brouillage prejudiciable, et (2) ce dispositif doit accepter
tout brouillage recu, y compris un brouillage susceptible de provoquer un
fonctionnement indesirable.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment.
This transmitter must be installed to provide a separation distance of at least 20cm
from all persons and must not be collocated or operating in conjunction with any
other antenna or transmitter.
Cet équipement est conforme aux limites d’exposition aux rayonnements IC RSS-102
définies pour un environnement non contrôlé.
Cet émetteur doit être installé pour fournir une distance de séparation d’au moins
20 cm de toutes les personnes et ne doit pas être colocalisé ou fonctionner en
conjonction avec une autre antenne ou émetteur.

TM
Like your new Wafer Downlight?
Share your experience!
Leave a review where you purchased
the product.
GE and C by GE is a trademark of General Electric Company. Used under trademark license.