GE HDTV Monitor User manual
HDTV Monitor User’s Guide
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol indicates
"dangerous voltage" inside the
product that presents a risk of
electric shock or personal injury.
WARNING
To reduce the risk of re
or electric shock, do not
expose this product to rain
or moisture. Caution: To reduce the risk of electric shock, do not remove cover (or back).
No user serviceable parts inside. Refer servicing to qualied service personnel.
This symbol indicates
important instructions
accompanying the product.
The apparatus shall not be exposed to dripping or splashing and that no
objects lled with liquids, such as vases, shall be placed on the apparatus.
Refer to the identication/rating label located on the back panel of your
product for its proper operating voltage.
FCC Regulations state that unauthorized changes or modications to this
equipment may void the user’s authority to operate it.
Caution: Using video games or any external accessory with xed images
for extended periods of time can cause them to be permanently imprinted
on the picture tube (or projection TV picture tubes). ALSO, some network/
program logos, phone numbers, black borders (sides, top and bottom), etc.
may cause similar damage. This damage is not covered by your warranty.
Cable TV Installer: This reminder is provided to call your attention to
Article 820-40 of the National Electrical Code (Section 54 of the Canadian
Electrical Code, Part 1) which provides guidelines for proper grounding
and, in particular, species that the cable ground shall be connected to the
grounding system of the building as close to the point of cable entry as
practical.
Warning: Do not use the Freeze feature for an extended period of time. This
can cause the image to be permanently imprinted on the picture tube. Such
damage is not covered by your warranty. Press any button to unfreeze the
picture at any time.
Product Registration
Please ll out the product registration card (packed separately) and return it immediately. Registering this
product allows us to contact you if needed. Your GE Consumer Electronics product may also be registered at
www.home-electronics.net/productregistration. Registering this product allows us to contact you if needed.
Product Information
Keep your sales receipt to obtain warranty parts and service and for proof of purchase. Attach it here and record
the serial and model numbers in case you need them. These numbers are located on the product.
Model No.__________________________________________________________________________________________
Serial No.___________________________________________________________________________________________
Purchase Date:______________________________________________________________________________________
Dealer/Address/Phone: ______________________________________________________________________________
Important Information
This symbol indicates that this product
incorporates double insulation between
hazardous mains voltage and user
accessible parts. When servicing use only
identical replacement parts.
1
Important Information
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers) that produce
heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the
other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your
safety. If the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they
exit from the apparatus.
11. Only use attachments/accessories specied by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the apparatus. When a
cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
If an outside antenna is connected to the TV receiver, be sure the antenna system is
grounded so as to provide some protection against voltage surges and built up static
charges. In the U.S. Section 810-21 of the National Electrical Code and in Canada, Part 1 of
the Canadian Electrical Code provides information with respect to proper grounding of the
antenna system. See the gure on the right for details.
Example of Antenna Grounding as per
(NEC) National Electrical Code
To assure adequate ventilation for this product, maintain a spacing
of 4 inches from the top and sides of the TV receiver and 2 inches
from the rear of the TV receiver and other surfaces.
2
Introduction
Key Features Overview
Your TV is equipped with features that will add to your TV viewing experience. The following
information summarizes a few of these features. Chapter 3 provides more information about the
rest of the TV’s features and how to use them.
TruScan Digital Reality
Picture performance starts with signal processing. TruScan Digital Reality intelligent signal
processing recognizes incoming video signals and progressively converts them to achieve
optimum digital picture performance. It enhances the picture quality and makes you feel as if
you’re close to the real thing. It also recognizes when original lm sources have been modied
and automatically converts the analog frame rate back to its original format to bring out the
detail – a process commonly referred to as reverse 3:2 pulldown.
Precision CRTs
Your HDTV monitor features Precision CRTs. These Precision CRTs (cathode ray tubes) produce
sharp, high-resolution images, with great detail and better transition between images than
regular CRTs.
HDTV Component Input (SYNCHROSCAN™)
Auto-adjusting inputs allow a wide array of component equipment to be connected to this
HDTV monitor. The SYNCHROSCAN circuits automatically detect and display video in various
formats including High Denition (HDTV, 1080i), Enhanced Denition (EDTV, 480p) and
standard denition (SDTV, 480i). This helps simplify the connection process.
V-Chip: Parental Controls (for the U.S. and Canada)
Description: You can block programs and movies by content, age-based ratings,
and/or movie ratings.
Requirements:
• Set up the Parental Control menu in the TV’s main menu (Chapter 3 has
details).
• The broadcasters must use the rating system when they send the program to
your TV in order for your TV to block the program.
• Parental controls must be locked for these settings to take effect.
Table of Contents
3
Important Safety Instructions.......................................... 1
Introduction
Key Features Overview .................................................... 2
Chapter 1: Connections & Setup
Things to Consider Before You Connect ......................... 4
Choose Your Connection .................................................. 5
TV + HDTV Tuner + VCR + DVD Player............................. 7
TV + Satellite Receiver + VCR ........................................... 9
TV + DVD + VCR .............................................................. 11
TV+ A/V Receiver ............................................................ 12
Explanation of Jacks ....................................................... 12
The Front of Your TV....................................................... 13
Front Input Jacks....................................................... 13
Front Panel Buttons.................................................. 14
Plug in the TV.................................................................. 14
Put batteries in the remote............................................ 14
How to Use the Remote Control to Complete
the Initial Setup........................................................... 14
Turn on the TV................................................................. 15
Complete the Initial Setup ............................................. 15
Set the Menu Language .......................................... 15
Complete Auto Channel Search............................... 15
Changing Lists and Labels ........................................ 16
Auto Convergence.................................................... 16
Chapter 2: Using the Remote Control
The Buttons on the Remote Control.............................. 17
Programming the Remote.............................................. 19
Find Out If You Need to Program the Remote ...... 19
Programming the Remote ....................................... 19
How to Use the Remote After You’ve
Programmed It .................................................... 21
Using the INPUT Button.................................................. 21
Remote Control Codes.................................................... 22
Chapter 3: Using the TV's Features
Channel Banner............................................................... 23
Autotuning...................................................................... 23
Why You Should Use the Autotuning Feature ....... 23
How to Set Up the Autotuning Feature.................. 24
Parental Controls and V-Chip ......................................... 25
How V-Chip Works for USA and Canada................. 25
US V-Chip TV Rating Limit........................................ 25
Canada V-Chip Ratings ............................................. 29
Blocking Canadian V-Chip Ratings .......................... 31
V-Chip Movie Rating Limit ....................................... 31
Blocking Unrated/Exempt Programs .................... 32
Lock/Unlock Parental Controls ............................... 32
Chapter 4: Using the Menu System
Sound Menu.................................................................... 33
Picture Menu ................................................................... 34
Channel Guide Menu...................................................... 36
Time Menu....................................................................... 36
Parental Control Menu ................................................... 36
Setup Menu..................................................................... 37
Chapter 5: Other Information
Troubleshooting.............................................................. 39
FCC Information .............................................................. 41
Care and Cleaning........................................................... 41
GE HDTV Monitor Limited Warranty ............................. 42
Accessory Information.................................................... 44
Index ................................................................................ 45
4 Chapter 1
Graphics contained within this publication are for representation only.
Chapter 1: Connections & Setup Connections & Setup
Chapter 1 5
Things to Consider Before You Connect
Protect Against Power Surges
• Connect all components before you plug any of their power cords into the wall outlet.
• Turn off the TV and/or component before you connect or disconnect any cables.
• Make sure all antennas and cables are properly grounded. Refer to the Important Safety
Instructions on page 1.
Protect Components from Overheating
• Don’t block ventilation holes on any of the components. Arrange the components so that air
can circulate freely.
• Don’t stack components.
• If you place components in a stand, make sure you allow adequate ventilation.
• If you connect an audio receiver or amplier, place it on the top shelf so the heated air from it
won’t ow around other components.
Position Cables Properly to Avoid Audio Interference
• Insert each cable rmly into the designated jack.
• If you place components above the TV, route all cables down the side of the back of the TV
instead of straight down the middle of the TV.
• If your antenna uses 300-ohm twin lead cables, do not coil the cables. Also, keep the twin
lead cables away from audio/video cables.
Important Stand and Base Safety Information
Choose the location for your TV carefully. Place the TV on a stand or base that is of adequate size
and strength to prevent the TV from being accidentally tipped over, pushed off, or pulled off. This
could cause personal injury and/or damage the TV. Refer to the Important Safety Instructions on
page 1.
Use Indirect Light
Don’t place the TV where sunlight or room lighting will be directed toward the screen. Use soft or
indirect lighting.
4 Chapter 1
Graphics contained within this publication are for representation only.
Chapter 1: Connections & Setup Connections & Setup
Chapter 1 5
TV
VCR
Components Cables Connection Go to...
Needed Title
Coaxial
Audio/video
Component
video
TV + HDTV Tuner
+ DVD + VCR
pages 6-7
TV + Satellite
Receiver + VCR
pages 8-9
TV
VCR
Coaxial
Audio/video
Component video
TV + DVD + VCR pages 10-11
Choose Your Connection
There are several ways to connect your TV. Please use the following chart to determine which connection is best for you.
Proceed to the appropriate page and connect your TV.
Note for US customers: If you prefer, we can provide you with the name of an Authorized Service Representative
who will visit your home for a fee to install your electronic entertainment system and to instruct you in its operation.
For details about this service, call 1-888-206-3359.
For general information on connecting an A/V receiver to your TV, go to page 12.
HDTV
Tuner
DVD
Satellite
VCR
Coaxial
Audio/video
S-Video
DVD
Audio/Video
cables
Component Video
(Y•Pb•Pr) cables
S-Video cableCoaxial cable
Cables Needed to Connect Components to Your TV
The pictures below show the cables needed for the connections represented in this book.
Notes: Audio/Video cables (A/V cables for short) are usually sold as a bundled set, but the connection pictures in this
book show each cable separately for better visibility.
TV
Connections & Setup
6 Chapter 1
Connections & Setup
Chapter 1 7
HDTV Tuner
1A
3
4A
5A
5B
1B
4B
5C
4C
6A
6B
VCR
TV
DVD
2
Connections & Setup
6 Chapter 1
Connections & Setup
Chapter 1 7
TV + HDTV Tuner + VCR + DVD Player
1. Make sure cable or antenna and/or satellite is connected to your HDTV Tuner.
A. Connect the coaxial cable from your cable outlet or antenna to the antenna input jack on the HDTV Tuner.
B. Connect the satellite dish antenna feed to the satellite input jack on the HDTV Tuner.
2. Make the video connection between your HDTV Tuner and the TV.
Connect three video grade cables to the CMP1 Y PB PR input jacks on the back of the TV and to the Y PB PR output
jacks on the HDTV Tuner.
3. Make the audio connection between your HDTV Tuner and the TV.
Connect the audio (white and red) cables to the CMP1 L and R audio input jacks on the back of the TV and to the
audio output jacks on the HDTV Tuner.
4. Connect your HDTV Tuner to your VCR.
A. Connect a coaxial cable to the HDTV Tuner’s antenna output jack and to VCR’s antenna input jack.
B. Connect the audio (white and red) cables to the audio output jacks on the HDTV Tuner and to the audio input jacks
on the VCR.
C. Connect the video cable to the video output jack on the HDTV Tuner and to the video input jack on the VCR.
5. Connect your VCR to your TV.
A. Connect a coaxial cable to the VCR’s antenna output jack and to the ANTENNA/CABLE input jack on the TV.
B. Connect the audio (white and red) cables to the VID2 L/MONO and R audio input jacks on the back of the TV and
to the audio output jacks on the VCR.
C. Connect the video cable to the VID2 V (video) jack on the back of the TV and to the video output jack on the VCR.
6. Connect your DVD player to your TV.
A. Connect the audio (white and red) cables to the VID1 L/MONO and R audio input jacks on the back of the TV and
to the audio output jacks on the DVD player.
B. If your DVD player has an S-Video jack, connect an S-Video cable to the S-VIDEO input jack on the TV and to the
S-VIDEO output jack on the DVD player.
Notes: If your DVD player doesn’t have an S-Video jack, connect the player to the TV’s VID1 V (video) jack using a
video cable.
Go to page 14
Connections & Setup
8 Chapter 1
Connections & Setup
Chapter 1 9
Satellite
1A
1B
2
4A
VCR
TV
1C
3
4B – OR –
Connections & Setup
8 Chapter 1
Connections & Setup
Chapter 1 9
TV + Satellite Receiver + VCR
1. Connect your VCR to your TV.
A. Connect a coaxial cable to the VCR’s antenna output jack and to the ANTENNA/CABLE
Input jack on the TV.
B. Connect the audio (white and red) cables to the VID2 L/MONO and R audio input jacks on
the back of the TV and to the audio output jacks on the VCR.
C. Connect the video cable to the VID2 V (Video) jack on the back of the TV and to the video
output jack on the VCR.
2. Make sure cable or antenna is connected to your VCR.
Connect the coaxial cable from your cable outlet or antenna to the antenna input jack on the
VCR.
3. Connect your satellite receiver's audio signal to your TV.
Connect the audio (white and red) cables to the VID1 L/MONO and R audio input jacks on
the back of the TV and to the audio output jacks on the satellite receiver.
4. Connect your satellite receiver's video signal to your TV.
A. Connect the video cable to the VID1 V (Video) input jack on the back of the TV and to the
video output jack on the satellite receiver.
– OR –
B. If your satellite receiver has an S-Video jack, connect an S-Video cable (instead of the video
cable in step B) to the S-VIDEO input jack on the TV and to the S-VIDEO output jack on
the satellite receiver.
Go to page 14
Connections & Setup
10 Chapter 1
Connections & Setup
Chapter 1 11
1A
2A
2B
3
DVD
1B
2C
VCR
TV
Connections & Setup
10 Chapter 1
Connections & Setup
Chapter 1 11
TV + DVD + VCR
1. Connect your DVD Player to your TV.
A. Connect the audio (white and red) cables to the CMP1 L and R audio input jacks on the
back of the TV and to the audio output jacks on the DVD player.
B. Connect three video grade cables to the CMP1 Y PB PR input jacks on the back of the TV
and to the Y PB PR output jacks on the DVD player.
Notes:
If your DVD player does not have Y PB PR jacks, but does have an S-Video jack, connect the
player to the VID1 S-VIDEO jack on the TV using an S-Video cable.
If your DVD player does not have an S-Video jack, connect the player to the VID1 V (Video)
jack on the back of the TV using a video cable.
Important: If you use the VID1 S-VIDEO or V (Video) jack to connect your TV to the DVD
player, you must connect the audio cables to the VID1 L/MONO and R jacks on the TV.
2. Connect your VCR to your TV.
A. Connect a coaxial cable to the VCR’s antenna output jack and to the ANTENNA/CABLE
input jack on the TV.
B. Connect the audio (white and red) cables to the VID2 L/MONO and R audio input jacks on
the back of the TV and to the audio output jacks on the VCR.
C. Connect the video cable to the VID2 V (Video) jack on the back of the TV and to the video
output jack on the VCR.
3. Make sure cable or antenna is connected to your VCR.
Connect the coaxial cable from your cable outlet or antenna to the antenna input jack on the
VCR.
Go to page 14
Connections & Setup
12 Chapter 1
Connections & Setup
Chapter 1 13
TV+ A/V Receiver
You can connect your TV to an A/V receiver using the AUDIO/VIDEO OUTPUT jacks.
Making the Connection
Connect audio cables to either the FIXED or VARIABLE
AUDIO L and R OUTPUT jacks and to the Audio Inputs on
the A/V receiver.
• FIXED provides xed-level audio output from the TV.
This audio output is ideal for connecting to an A/V
receiver that has its own volume control.
• Variable provides variable-level audio output. Volume
levels can be controlled by the volume controls on the
TV and TV remote control.
ANTENNA/CABLE Lets you connect a coaxial cable to receive the signal from the
antenna, cable, cable box, or if using the examples on pages 6-11, a VCR.
Explanation of Jacks (in alphabetical order)
This section describes the jacks you can use to make connections. There are several ways to
connect components to your TV.
AUDIO/VIDEO OUTPUT Lets you connect an amplier or audio receiver for improved
sound quality or an external video monitor.
• FIXED AUDIO L/R Provides xed-level audio output from the TV. This audio
output is ideal for connecting an A/V receiver when you want to control the volume
through the A/V receiver.
• VARIABLE AUDIO Provides variable-level audio output. Volume levels are
controlled by the volume controls on the TV and remote control.
• SUBWOOFER Provides lower bass audio frequencies from the TV to a subwoofer.
Note: If you’ve connected a subwoofer, make sure you set the External Subwoofer
option in the Sound menu. Go to page 33 for instructions.
COMPONENT INPUT Lets you connect a component video source, such as a DVD
player.
• CMP1 Y PB PR (Component Video) Provides optimum picture quality because
the video is separated into three signals. Use three video-grade cables for the
connection. When using CMP1 Y PB PR, make sure to connect left and right audio
cables to the CMP1 L and R Audio Input jacks.
• CMP1 L (Audio) Provides left audio connection. The left audio connector is
usually white.
• CMP1 R (Audio) Provides right audio connection. The right audio connector is
usually red.
Connections & Setup
12 Chapter 1
Connections & Setup
Chapter 1 13
COMPOSITE INPUTS Lets you connect another component such as a VCR,
DVD player, or laserdisc player. Its AUDIO jacks are the same as described for
CMP1 above.
• VID1 S-VIDEO Provides better picture quality than the video jacks (VID1
and VID2) because the color part of the picture is separated from the black
and white part of the picture. When using VID1 S-VIDEO, make sure to
connect left and right audio cables to the VID1 L/MONO and R Audio Input
jacks.
• VID1 V (Video) Provides composite video connection. The video
connector is usually yellow.
• VID2 S-VIDEO, V and L/MONO and R Audio Allows you to connect
a component such as a VCR, DVD player, or laserdisc player. Their
description is the same as VID1 above.
Note: For each VID jack group (VID1 and VID2), you may connect either
an S-Video or Video cable. Do not connect both at the same time in either
of the VID jack groups.
The Front of Your TV
Front Input Jacks
The TV has front inputs for convenience: one set of audio/video input jacks, an
S-Video jack and a headphones jack. The jacks are ideal for using a video game
console or a camcorder. Locate the jacks either on the front of the TV or on one
of the sides. To access the component you connected to the front of the TV,
press the INPUT button on your remote until FRNT appears on the screen.
Note: When connecting a component that uses a monaural cable, such as
some camcorders, use the Left (mono) input jack to get sound from both
speakers.
PHONES Allows you to connect headphones to listen to the sound coming
from the TV. To adjust volume control of the headphones, press the VOL > or
VOL < button (the volume display appears). Press the arrow up or down button
(the headphone volume display appears), then press the right or left arrow
button to adjust the headphone volume.
VIDEO (in) Receives video from another component such as a camcorder,
video game console, or VCR.
L/MONO and R AUDIO Receives audio from another component such as a
camcorder, video game console, or VCR.
S-VIDEO (in) Allows you to connect an S-Video cable from another
component. Make sure you also connect audio cables from the component to
the TV.
Note: Do not connect an S-Video and a regular video cable to the FRNT
jacks at the same time.
Continues on next page...
Connections & Setup
14 Chapter 1
Connections & Setup
Chapter 1 15
Front Panel Buttons
If you cannot locate your remote, you can use the front panel buttons of your TV
to operate many of the TV’s features.
MENU/OK Brings up the Main menu. In the menu system, it selects highlighted
items.
CH Scans down through the current channel list. In the menu system, acts like
the down arrow button on the remote control and adjusts menu controls.
CH Scans up through the channel list. In the menu system, acts like the up
arrow button on the remote control and adjusts menu controls.
VOL < Decreases the volume. In the menu system, acts like the left arrow button
on the remote control and adjusts menu controls.
VOL > Increases the volume. In the menu system, acts like the right arrow button
on the remote control and adjusts menu controls.
POWER Turns the TV on and off.
Plug in the TV
Plug the end of the power cord into a grounded wall outlet. Insert the plug
completely into the outlet.
Put batteries in the remote
• Remove the battery compartment cover from the back of the remote by
pushing the tab and lifting off the cover.
• Insert two fresh batteries. Make sure the polarities (+ and -) are aligned
correctly.
• Replace the cover.
How to Use the Remote Control to
Complete the Initial Setup
The technical term is “Navigation” – how you move through the on-screen menus.
The theory is the same throughout the menu screens: highlight your choice and
select it.
To highlight a menu item, press the arrow buttons on the remote to highlight one
of the items listed on the screen. Use the up or down arrow button to move up or
down. Use the right or left arrow button to move right or left.
To select the item that you’ve highlighted, press OK.
Note: Highlighted means that the menu item stands out from other menu
items on the list (appears darker, brighter, or a different color).
>
>
123
456
789
0
TV button
Arrows
OK
button
Connections & Setup
14 Chapter 1
Connections & Setup
Chapter 1 15
Turn on the TV
Press TV on the remote, or press POWER on the TV’s front panel.
Note: Pressing the TV button not only turns on the TV, but puts the remote
into TV mode. “TV mode” means that the buttons on the remote control
operate the TV’s functions.
Complete the Initial Setup
The menu system in your TV allows the TV’s features to work properly. The rst
time you turn on your TV, the setup screens appear. Complete the entire setup
sequence including Auto convergence to prevent the setup screen from appearing
the next time the set is turned on.
Set the Menu Language
The rst part of the setup allows you to select your preferred language for the
menu system.
If English is your preferred language, press OK. If you want to choose another
language, press the down arrow button until that language is highlighted, and
press OK.
Tip
To access the setup menus manually, press
MENU and choose SETUP.
Continues on next page...
Complete Auto Channel Search
The next screen asks you to make sure you've connected the TV to a cable,
satellite, or off-air signal. When you're sure that a signal is connected to your TV,
press OK on your remote to go to the Channel setup screen.
In the Channel setup screen, you can launch the Auto channel search by
pressing OK. The Auto channel search allows the TV to search for all channels
viewable through your antenna or cable TV system. This is sometimes called auto
programming. When the channel search is complete, press OK to access the List &
Labels screen.
Connections & Setup
16 Chapter 1
Changing Lists and Labels
The List & Labels part of the setup lets you edit your channel list and choose or
create a personal six-character label for each channel.
Note: Changing List and Labels can be time consuming. You can change
these at a later time by accessing the Setup menu.
1. Press the left or right arrow button to scroll through the channels and choose
the one you want to edit.
2. Press the down arrow button to highlight the In channel list option. Press the
left or right arrow button to add (the box is checked) or remove (the box is
unchecked) the channel from the list.
3. Press the down arrow button to highlight the Channel label option. Press
the left or right arrow button to scroll through the available list of 25 most
common labels. The last option in the list allows you to create your own six-
character label for the channel (the rst letter of the label is highlighted).
4. Press the 1 or 2 number button to change the rst letter of the label.
5. Press the right arrow button to highlight the second letter, then press the 1 or
2 number button to change the second letter, etc...
6. When you are nished creating your label, press OK. Select Go back to go to
the Auto Convergence menu.
Auto Convergence
Your TV’s picture tubes might have been disturbed during delivery or after you
moved the TV, causing the color in your TV to be out of alignment. The colors
adjust by starting auto convergence.
IMPORTANT: Auto convergence works best once the TV has warmed up for
at least an hour. If you've just unpacked your TV, it's a good idea to repeat
the Auto convergence function when the TV's been running for at least an
hour. See page 38 for more information about Auto convergence.
1. Press OK to begin auto convergence.
2. When the auto convergence is complete, the Red center convergence menu
appears. The cross in the middle of the screen should be yellow. If it is not,
use the arrow buttons to move the red cross to overlap the green cross. Press
OK when adjustments are complete.
3. The Blue center convergence menu appears with a cyan cross in the middle
of the screen. If it is not, use the arrow buttons to move the blue cross to
overlap the green cross. Press OK (the TV tunes to the last selected/available
channel in the channel list).
Note:
If you're using an HD source (such as an
HDTV tuner or HDTV satellite receiver) on
the CMPNT input, you should run Auto
convergence separately for that input as well.
Tune to the input you’re using for the HD
source, then go to page 38 for information on
Auto convergence.
Chapter 2 17
Graphics contained within this publication are for representation only.
Chapter 2: Using the Remote Control
The Buttons on the Remote Control
(0-9) Number Buttons Enter channel numbers and time settings directly
through the remote control.
To enter a one-digit channel, enter a zero rst. To enter a two-digit channel,
press the two digits. To enter a three-digit channel, press and hold the 1 button
until 1 and two dashes (– –) appear, then add the second two digits. Example:
to tune to channel 123, press and hold 1 until 1– – appears, release the 1 button
and then press 2 and 3.
ANTENNA In VCR mode (if programmed), this button works as a TV/VCR
button for some VCRs. In SAT mode (if programmed), this button works as a
TV/SAT button for some satellite receivers.
Arrows Used to highlight different items in the TV menu and to adjust the
menu controls. When watching TV without the menu system in use, the left and
right arrows change the current format of the screen, exactly like the FORMAT
button described below.
AUX•HD Puts the remote in AUX/HD mode. As a default, this button controls
some models of RCA HDTV Tuners. It can also be programmed to operate
some brands of an additional remote-controllable components. The Autotuning
feature for this button works only with HDTV tuners (see page 23 for more
information on Autotuning).
CC Displays a reduced Closed Captioning menu, allowing you to turn closed
captioning on and off or change the closed captioning mode. Use the up and
down arrow buttons to highlight the setting you want to change. Use the left
and right arrow buttons to change the highlighted setting.
CH + or CH - Scans up or down through the current channel list. Press once
to change the channel up or down; press and hold to continue changing
channels. In DVD mode (if programmed), these buttons work as chapter
advance or chapter reverse buttons with some DVD players.
CLEAR Removes any menu or display from the screen and returns you to
normal viewing.
DVD Puts the remote in DVD mode and, if Autotuning is enabled, will turn on
the TV and tune to the correct video input channel.
FORMAT Changes the current format (aspect ratio and magnication) of the
image on the screen.
FREEZE When watching TV, freezes the picture until you press any button
on the remote to resume normal TV viewing. The FREEZE feature automatically
times out after a short time. Please note that when you "unfreeze" you go back
to live programming (skipping any programming that occurred during the
freeze).
Note: The FREEZE feature does not work on signals from the CMP1 input in
progressive scan (480p) or HDTV (1080i) modes.
Do not use the Freeze feature for an extended period of time. This can cause
the image to be permanently imprinted on the picture tube. Such damage is
not covered by your warranty. Press any button to unfreeze the picture at any
time.
Indicator
Continues on next page...
18 Chapter 2
Using the Remote Control
Chapter 2 19
Using the Remote Control
Note:
The DVD and AUX•HD buttons also turn on
most RCA, GE, and Proscan products.
Tip
To turn off all the RCA, GE, and Proscan
components that are connected to the TV,
press ON•OFF twice within two seconds.
This feature only works with most RCA, GE,
and Proscan products.
GO BACK Returns you to the previous channel.
GUIDE Brings up the Channel Guide menu.
Indicator Indicates the programming mode when programming the remote to
control components. The indicator lights up when you press a valid button on
the remote. It ickers when the remote batteries are low and you press a button.
INFO Brings up channel banner; press again to clear the screen.
INPUT Press to toggle through the available input sources (VID1, VID2, FRNT
and CMP1—press the CH+ or CH- button to resume TV viewing).
MENU Brings up the Main menu.
MUTE Reduces the TV’s volume to its minimum level. Press again to restore
the volume.
OK When in the menu system, selects highlighted items. When watching
TV, freezes the picture until you press any button on the remote to resume
normal TV viewing. Please note that when you "unfreeze" you go back to live
programming (skipping any programming that occurred during the freeze).
ON•OFF When in TV mode, turns the TV on and off. If in another component
mode (DVD or AUX•HD) and programmed, will turn the component on and
off. When pressed twice within two seconds, the ON•OFF button turns off most
RCA, GE and Proscan components.
PRESETS Displays the Picture and Sound preset settings. Use the up and down
arrow buttons to highlight either Picture or Sound settings. Use the left and right
arrow buttons to change to a different Picture or Sound preset.
REVERSE, PLAY, FORWARD, RECORD, STOP, PAUSE If programmed,
provides transport control for some remote-controllable VCRs and DVD players.
SLEEP Displays the Sleep Timer. Each press adds an additional 15 minutes.
SKIP Press once before changing channels and the TV will wait 30 seconds
before returning you to the original channel. Press repeatedly to add more time.
TV Turns on the TV and puts the remote in TV mode. Also displays current
status.
VOL – or VOL + Decreases or increases the TV’s volume.
Tip
The indicator ashes when the remote
batteries are low and you press a button on
the remote.
A warning banner may also appear on the
screen when you press a remote button and
your batteries are low.
Table of contents
Other GE Monitor manuals
GE
GE 1926A-1AN User manual
GE
GE Dinamap PRO Series User manual
GE
GE 3500/40M User manual
GE
GE IC754VKI06MTD User manual
GE
GE Corometrics 250cx Series User manual
GE
GE PACSystems ICRXIDIXNE19LCTA User manual
GE
GE UVis-920 User manual
GE
GE TMO2D User manual
GE
GE Aritech ATS1100 User manual
GE
GE Bently Nevada 3300/03 User manual
GE
GE Responder 2000 User manual
GE
GE QuickPanel+ IC755CxS06RDx User manual
GE
GE B40 User manual
GE
GE TRANSFIX DGA 500 User manual
GE
GE EPM 3000P User manual
GE
GE IC754VBB06CTD User manual
GE
GE CareScape V100 User manual
GE
GE CARESCAPE User manual
GE
GE Kelman Minitrans User manual
GE
GE KITCHEN HUB UVH1301 User manual
