GE Built-In Dishwasher User manual

Ilnstallat!on
nstruct=ons
Built-In Wall Oven
27" (68.6 cm) models
JKS10, JKP30, JKP35, JKP55, JKP70, JKP75,
PK916, PK956, ZEK938, ZEK958
30" (76.2 cm) models
JTP30, JTP35, JTP55, JTP70, JTP75, PT916,
PT920, PT956, PT960, ZET938, ZET958
If you have questions, call 1.800.GE.CARES or visit our website at:
ge.com
Before You Begin
Read these instructions carefully and completely.
• IMPORTANT-save these
instructions for local inspector's use.
•IMPORTANT-observe all
governing codes and ordinances.
• Note to Installer--Be sure to leave these
instructions with the consumer.
•Note to Consumer--Keep these
instructions for future reference.
•Proper installation is the responsibility
of the installer and product failure due
to improper installation is NOT covered
under warranty.
•NOTE--This appliance must be properly
grounded.
•ATTENTION INSTALLER
All electric wall ovens must be hard wired
(direct wired) into an approved junction
box. A plug and receptacle is NOT permitted
on these products.
Parts Included
(Appearance will vary)
Screws For Installation
(8-18 x .750 flat head
Phillips wood screws)
(68.6 cm)
Metal Bottom
Trim Assembly
(on some models or
can be purchased
separately)
27" (68.6 cm)
Metal Bottom Trim
30" (76.2 cm)
Metal Bottom Trim
Assembly
Materials Needed
Strain Relief Clamp
for 1/2" conduit Junction Box
Wire Nuts
36" (91 cm)
of String
Tools Needed
1/8" (3 mm) Drill Bit and
Electric or Hand Drill Phillips Screwdriver
31-10647 02-07 JR

Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
For Your Safety
•Be sure your oven is installed properly by
a qualified installer or service technician.
• Be sure the oven is securely installed in a
cabinet that is firmly attached to the house
structure. Weight on the oven door could
cause the oven to tip and result in injury.
Never allow anyone to climb, sit, stand or
hang on the oven door.
• Make sure the cabinets and wall
coverings around the oven can withstand
the temperatures (up to 200°F [93.3°C])
generated by the oven.
WARNING: The electrical
power to the oven supply line
must be shut off while line
connections are being made. Failure
to do so could result in serious injury
or death.
Electrical
Requirements
This appliance must be supplied with the proper
voltage and frequency, and connected to an
individual, properly grounded branch circuit,
protected by a circuit breaker or fuse. See the
rating plate located on the oven frame to determine
the rating of the product. Use the chart below to
determine the minimum recommended dedicated
circuit protection. Recommended
KW Rating KW Rating Circuit Size
240V 208V (Dedicated)
<4.8 KW <4.1 KW 20 Amp
4.9 KW-7.2 KW 4.3 KW-6.2 KW 30 Amp
7.3 KW-9.6 KW 6.3 KW-8.3 KW 40 Amp
9.7 KW-12.0 KW 8.4 KW-10.4 KW 50 Amp
Electrical
Requirements cont.
Rating plate is located on oven side trim,
side front frame or lower front frame.
F --
Rating Plate
Location _ r'--_
I -- I
We recommend you have the electrical wiring
and hookup of your oven connected by a qualified
electrician. After installation, have the electrician
show you where your main oven disconnect is
located.
Check with your local utilities for electrical codes
which apply in your area. Failure to wire your oven
according to governing codes could result in a
hazardous condition. If there are no local codes,
your oven must be wired and fused to meet the
requirements of the National Electrical Code,
ANSI/NFPA No. 70-Latest Edition. You can
get a copy by writing:
National Fire Protection Association
Batterymarch Park
Quincy, MA 02269
Effective January 1, 1996, the National
Electrical Code requires that new, but not existing,
construction utilize a four-conductor connection to
an electric oven. When installing an electric oven
in new construction, a mobile home, recreational
vehicle or an area where local codes prohibit
grounding through the neutral conductor,
follow the instructions in the section on NEW
CONSTRUCTION AND FOUR-CONDUCTOR
BRANCH CIRCUIT CONNECTION.
You must use a three-wire, single-phase A.C.
208Y/120 Volt or 240/120 Volt, 60 hertz electrical
system. If you connect to aluminum wiring,
properly installed connectors approved for
use with aluminum wiring must be used.
2

Installation Instructions
Pre-lnstallation Checklist
ALL INSTALLATION INFORMATION
ON THE FOLLOWING PAGES IS TO
BE USED FOR SINGLEAND DOUBLE
OVEN INSTALLATION!
i
Door removal is not a requirement for
installation of the product, but is an
added convenience. To remove the door:
Open the oven door as far as it will go.
Remove packaging materials.
Check behind hinges and under
false bottom. Remove labels on the
outside of the door, plastic on trims
and panel, all tape around the oven,
and any shipping screws securing
the oven to the base pad.
F o_
Oven Racks
_iterature
Pack
Open oven door and remove literature
pack and oven racks.
Remove Installation Instructions from
literature pack and read them carefully
before you begin.
Be sure to place all literature, Owner's
Manual, Installations, etc. in a safe place
for future reference.
Push both hinge Hinge
_._L. Unlocked
locks down toward _l_'.!_b. Position
the door frame, Hinge"':':':_
to the unlocked s_ot __.d
position. This may
require a flat blade Hinge
screwdriver. Arm
DO NOT LIFT THE DOOR
BY THE HANDLE!
Place hands on both sides of "T_-_
the door, and close the oven II_ji_:_
door to the removal position, I_/
which is most of the way closed. I_//
[_ ift door up and
out until the
hinge arms
clear the slots.
Hinge Clears Slot
NOTE: The oven door is very heavy. Be sure
you have a firm grip before lifting the oven
door off the hinges. Use caution once the
door is removed. Do not lay the door on its
handle. This could cause dents or scratches.
Place the oven on a table or platform
even with the cutout opening. (Platform
must support 150 Ibs. [68 Kg] single,
275 Ibs. [124 Kg] double.)
Remove the bottom trim from the top
of the oven. It will be installed at the end
of the installation process. The trim is
wrapped separately and taped to
the top of the unit.
3

Installation Instructions
Cutout for 27"(68.6cm)Single Built-In
Ovens only
For JKS10, JKP30, JKP70, PK916, ZEK938 models only.
Allow 1" (2.5 cm)
for overlap of
oven over side
edges of cutout
2"x4"
(5crux lOcm)
or
runners level
with bottom
of cutout
5" (12.7 cm)
Max. from the
left or right
Cabinet _side
--Width _
"l
Cutout Width
25" (63.5 cm)
Min. _"
25 114" (64.1
Max.
Junction Box
Location
Cutout
Height 22" (55.9 cm)
27 5/8" Min. above
(70.2 cm) Min. base rail
28 1/8"
Cabinet Width
Recommended
Cutout Location
from Floor
Cutout Depth
Cutout Width
Cutout Height
27" (68.6 cm)
32 1/2" (82.6 cm)
23 1/2"
(59.7 cm) Min.
25" (63.5 cm) Min.
25 1/4" (64.1 cm) Max.
27 5/8" (70.2 cm) Min.
28 1/8" (71.4 cm) Max.
20" (50.8 cm)
_joJ-" j--
- 7-
-.. __. ___ -.. .......Allow
Allow a minimum 1 3/8" (3.5 cm)
minimum for
of 20" (50.8 cm) for
clearance to adjacent overlap of
corners, drawers, walls, oven top and
bottom
etc. when door is open of cutou_"-_
Recommended
cutout location
from floor 32 1/2"
(82.6 cm)
Alternate Junction
Box Location -
access from
adjacent cabinet
may be required
NOTE: If the cabinet does not
have a front frame and the sides
are less than 3/4" (1.9 cm) thick,
shim both sides equally to
establish the cutout width.
If the cabinet does not have a solid bottom,
two braces or runners must be installed
level with the bottom of the cutout to
support the weight of the oven. For
single ovens, the runners and braces
must support 150 Ibs (68 Kg).
NOTE: If marks, blemishes or the
cutout opening are visible above the
installed oven, it may be necessary to
add wood shims under the runners and
front trim until the marks or opening
are covered.
2"x4"(5cmx 10cm) or
equivalent runners level
with bottom of cutout
T
24"
(61 cm)
1
f
I_- 18" (45.7 cm) --i
27" (68.6 cm) "_
These ovens are not approved for
stackable installations.
4

Installation Instructions
Cutoutfor27"(68.6 DoubleBuilt-In
Ovensonly
For JKP35, JKP55, JKP75, PK956, ZEK958 models only.
Allow 1" (2.6 cm)
for overlap of
over over side
edges of
6"
(12.7 cm)
Max. from
the left or
Cabinet right
(68.6 cm)
Cutout
(63.5 cm) Men.
25 1/4" i
(64.1 cm) Ma_.
2" x 4"
(Scmx10cm)
or equivalent
runners
20"(60.6
jj j
................ Allow 1 3/8"
/(3.6 cm) for
Allow a minimum
of 20" (50.8 cm)
for clearance to
adjacent corners,
drawers, walls, etc.
when door is open
iJunction Box
_F._ Location
iii zzI
(111.6 cm)
Min,
iCut°ut Above
iHeight base rail
i49 11/t6"
i(126.2 cm) Men.
160118"
i(127.3 cm) Max.
Recommended
cutout location
overlap of oven from floor 13 1/4"
top and bottom_ (33.7 cm)
of cutout
Cabinet Width
Recommended
Cutout Location
from Floor
Cutout Depth
Cutout Width
Cutout Height
27" (68.6 cm)
13 1/4" (33.7 cm)
23 5/8" (60 cm) Men.
25" (63.5 cm) Men.
25 1/4" (64.1 cm) Max.
49 11/16" (126.2 cm) Men.
50 1/8" (127.3 cm) Max.
NOTE: If the cabinet does
not have a front frame and
the sides are less than 3/4"
(1.9 cm) thick, shim both
sides equally to establish
the cutout width.
If the cabinet does not have a solid bottom,
two braces or runners must be installed to
support the weight of the oven. For double
ovens, the runners and braces must
support 300 Ibs (135 Kg).
NOTE: If marks, blemishes or the
cutout opening are visible above the
installed oven, it may be necessary to
add wood shims under the runners and
front trim until the marks or opening
are covered.
Suitable
Bracing
to Support
18" _-
-T (45.7 cm)
Over Centerline
of Cabinet
2" x 4"
(Scmx10cm)
or equivalent
runners level
with bottom
of cutout
5

Installation Instructions
IAICutout for 27" (68.6cm)Single Built-In
Ovens only Under Counter
For JKS10, JKP30, JKP70, PK916, ZEK938 models only.
Gas or electric cooktops may
be installed over this oven.
See cooktop installation
instructions for cutout size,
See label on top of oven for
approved cooktop models.
25" (63.5 cm) \. \\
Top and/or side fillers
may be necessary
if unit is positioned
between existing
cabinets. Be sure
they are attached
securely, since they
will anchor the oven
in the cabinet.
240V /208V
Junction Box
Location 5"
(12.7 cm)
Max. from the
left or right
side
_25" (63.5 cm) Min.
25 1/4" (64.1cm) Max. Allow "_
1 318"
(3.5 cm)
unit overlap top
bottom of
oven, 1" (2.6 cm)
unit overlap side
edges
27 5/8" (70,2 cm) Min.
28 1/8" (71.4 cm) Max. "'; ""
Gas and electrical connections
for gas cooktop must be located
in an adjacent accessible
location to the right.
22" (55.9 cm) Min.
Above Support
Platform
24" (61cm)
36" (91.4 cm)
Typical
Countertop
Height
6

Cabinetry
Cutout for 27" (68.6cm)Single or
Double Built-In Ovens only- Over a
Warming Drawer
For JKS10, JKP30, JKP35, JKP55, JKP70, JKP75, PK916, PK956, ZEK938,
ZEK958 models only.
Single 27" (68.6 cm)
Oven Over
a Warming Drawer
Double 27" (68.6 cm)
Oven Over
a Warming Drawer
Per
Warming
Drawer
Requirement
Anti-Tip Block Against
Rear Wall Per Warming
Drawer Requirement
3" (7.6 cm)
Min,
NOTE: Install the
oven only with
specific models
listed on the label
located on top of
the oven.
1" (2,6 cm) Min, Above Toekick or
Adjust to Oven Installation Height
NOTE: Additional clearances between cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location
do not obstruct the required interior depth and
height,
Anti-Tip Block
Against Rear
•Wall Per
Warming
Drawer
Requirement
3" (7.6 cm)
Min.
Per Warming
Drawer
Req_
1" (2.6 cm) Min. Above Toekick
•When installing a Warming Drawer below
a single or double oven, a separate 120V,
60 Hz, properly grounded receptacle must
be installed. Refer to installation instructions
packed with the Warming Drawer for
specific installation requirements.
7

Cabinetry
Cutout for 27" (68.6cm)Single Ovens
only- Below an Advantium or
Between an Advantium and a
Warming Drawer
For JKS10, JKP30, JKP70, PK916, ZEK938 models only.
Single 27" (68.6 cm) Oven
Below an Advantium Single 27" (68.6 cm) Oven Between an Advantium and
a Warming Drawer
Per Advantium
Requirement 3" (7.6 cm) Min. Per AdvantiL
Requirement 3" (7.6 cm) Min.
Note: Install the
oven only with
specific models
listed on the label
located on top of
the oven.
NOTE: The middle rail separating the two
openings may need to be larger than the 3"
(7.6 cm) minimum shown. Always refer to the
individual installation instructions packed with
each product for specific requirements.
Combined Advantium and Wall
Oven Installation:
When installed in combination with a
single wall oven, use separate electrical
junction boxes.
.Refer to the Advantium oven installation
instructions for electrical requirements of
that product.
. These connections must be made
by a qualified electrician. All electrical
connections must meet National Electrical
Code or prevailing local codes.
Per Warming
Drawer
Req
3" (7.6 cm) Min.
NOTE: Additional clearances may be
required. Check to be sure the oven
supports above the Warming Drawer
do not obstruct the required interior depth
and height. The middle rail separating the
openings may need to be larger than the 3"
(7.6 cm) minimum shown. Always refer to
the individual installation instructions packed
with each product for specific requirements.
Warming Drawer
Combined with Advantium
and Single Oven:
Install a separate 120V, 60Hz, properly
grounded receptacle. See installation
instructions packed with each product
for specific requirements.
8

Installation Instructions
Cutoutfor 30"(76.2 cm)Single Built-In
Ovens only
For JTP30, JTP70, PT916, PT920, ZET938 models only.
Allow 11/16"
(1.75 cm) for
overlap of oven
over side edges
of cutout
21" (53.3 cm) - - "
S
Allow aminimum
of 21" {63.3 cm) for
clearance to adjacent
corners, drawers,
walls, etc. when
door is open
Cutout 7 3/4" (19.7 cm)
Width Max. Junction Box
28 1/2" (72.4 cm) Location
Min. _(junction box
28 5/8" (72.7 cm). may be
Max. located in
---- ___ adjacent
/cabinet)
Between IN cutout I I i
Inside Walls I [_ Height i i . 22" (56.9 cm)
Must Be II_ 27 1/4" Bin, to
I tN (69.2 cm) Bottom of
At Least Min.
28 112" I 1_27 5/16" Junction Box
(69.4
(72.4 cm) cm) Max.
Wide"
top and 1W"
(3,2 cm) overlap
of oven bottom
of cutout_-_,
Cabinet
Width
30" (76.2 cm)
"!-
Recommended
cutout location
from floor 32 1/2"
Cabinet Width
Recommended
Cutout Location
from Floor
Cutout Depth
Cutout Width
Cutout Height
If the cabinet does not have a solid bottom,
two braces or runners must be installed
level with the bottom of the cutout to
support the weight of the oven. For single
ovens, the runners and braces must
support 150 Ibs (68 Kg).
NOTE: If marks, blemishes or the
cutout opening are visible above the
installed oven, it may be necessary to
add wood shims under the runners and
front trim until the marks or opening
are covered.
These ovens are not approved for
stackable installations.
30" (76.2 cm)
32 1/2" (82.6 cm)
23 1/2" (69.7 cm) Min.
28 1/2" (72.4 cm) Min.
28 6/8" (72.7 cm) Max.
27 1/4" (69.2 cm) Min.
27 6/16" (69.4 cm) Max.
NOTE: If the cabinet does
not have a front frame and the
sides are less than 3/4" (1.9 cm)
thick, shim both sides equally to
establish the cutout width.
Suitable
Bracing
to Support
Runners --
-- 2" x 4"
(5 cm x 10 cm
or equivalent
runners level
with bottom
of cutout
-F----- 64 215/8-
.9 cm) Over \
Centerline
of Cabinet
Side by Side Installations
Install two wall ovens in separate cutouts.
Allow 2" (5.1 cm) min. between cutouts (PT920
models) or 6" (15.2 cm) min. between cutouts
(all other models).
Cutout - 2" (5.1 cm) Cutout -
Observe all Min. (PT920) Observe all
dimensionsl_ dimensions
and 6" (15.2 cm) and
r_lu rements. Min. requirements.
(other models
9

Installation Instructions
IAICutoutfor30' 6.2cm)Double Built-InOvensonly
For JTP35, JTP55, JTP75, PT956, PT960, ZET958 models only.
Allow 11/16"
(1.75 cm) for
overlap of oven
over side edges
of cutout
Allow a minimum
of 21" (53.3 cm) for
clearance to adjacent
corners, drawers,
walls, etc, when
door is open
21" (53.3 cm)
Cutout
Width
28 112" (72.4 cm)
Min,
28 518" (72.7 cm)
==: Max.
Opening I
Between I
Inside Walls I
Must Be At
Least 28 1/2"
_,llow1" (2.5cm)
minimum for
overlap of oven
top and 1W"
(3.2 cm) overlap
of oven bottom
of cutout
Cabinet
Width
I
7 3/4"
(19.7 cm Junction Box Cabinet Width
) Location
(junction box Recommended
may be Cutout Location
located in
adjacent
cabinet)
/
-1
47" (119.4 cm)
Min.
to Bottom of
Junction Box
51 13/16" (131.6 cm)
Min.
51 15/16" (131.9 cm)
Max
i
Suitable
Bracing
to Support
Runners --
Recommended
cutout location(30.5 cm)
If the cabinet does not have a solid bottom,
two braces or runners must be installed
level with the bottom of the cutout to
support the weight of the oven. For
double ovens, the runners and braces
must support 275 Ibs (124 Kg).
from Floor
Cutout Depth
Cutout Width
Cutout Height
30" (76.2 cm)
12" (30.5 cm)
23 1/2" (59.7 cm) Min.
28 1/2" (72.4 cm) Min.
28 5/8" (72.7 cm) Max.
51 13/16" (131.6 cm) Min.
51 15/16" (131.9 cm) Max.
NOTE: If the cabinet does not
have a front frame and the sides
are less than 3/4" (1.9 cm) thick,
shim both sides equally to
establish the cutout width.
-- 2" x 4"
(Scm x 10cm)
or equivalent
runners level
with bottom
of cutout
-_(54, 21 5/8"-------_
9 cm) Over \
Centerline
of Cabinet
NOTE: If marks, blemishes or the
cutout opening are visible above the
installed oven, it may be necessary to
add wood shims under the runners and
front trim until the marks or opening
are covered.
10

Installation Instructions
IAICutoutfor 30"(76.2cm)Single Built-InOvens
only Under Counter
For JTP30, JTP70, PT916, PT920, ZET938 models only.
Gas or electric cooktops may be installed over this oven. See
cooktop installation instructions for cutout size. See label on
top of oven for approved cooktop models.
,\
25" (63.5 cm)
Top and/or side fillers
may be necessary
if unit is positioned
between existing
cabinets. Be sure
they are attached
securely, since they
will anchor the oven
in the cabinet.
240V /208V
Junction Box
Location (junction
box may be in
adjacent cabinet)
7 3/4"
(19.7 cm)
\_ ,- _"Max_ madegaScooktoP,tothe left,theconnections may
- 28 1/2" (72.4 cm) Min.
28 5/8" (72.7 cm) Max. Allow 1"
overlap top
of oven,
11/16" (1.8 cm)
overlap side edges
of cutout and
1 1/4" (3.2 cm) -
overlap bottom
of oven.
Gas and electrical connections
for 30" (76,2 cm) gas cooktop must
be located in an adjacent accessible
location to the right, For 36" (91.4 cm)
be
22" (55.9 cm) Min.
Above Support
Platform
24" (61 cm)
36" (91.4 cm)
Typical
Countertop
Height
4" (10.2 cm)
Typical
Toekick
NOTE: This oven is not ap-
proved to be installed under a
solid disk, induction or
downdraft modular cooktop.
=
Side by Side Installations
Install two wall ovens in separate cutouts.
Allow 2" (5.1 cm) min. between cutouts
(PT920 models) or 6" (15.2 cm) min.
between cutouts (all other models).
Cutout- 2" (5.1 cm)
Observe all Min, (PT920)
dimensionsl_
and 6"(15,2cm) Min.
requtrements. (othermodels)
11
Cutout -
Observe all
dimensions
and
requirements.

Cabinetry
Cutout for 30"(76.2cm) Single or Double
Built-In Ovens only- Over a
Warming Drawer
For JTP30, JTP35, JTP55, JTP70, JTP75, PT916, PT920, PT956, PT960,
ZET938, ZET958 models only.
Single 30" (76.2 cm)
Oven Over a Warming
Drawer
Double 30" (76.2 cm)
Oven Over a Warming
Drawer
Per Warming
Drawer
Requirement
Block Against
Rear Wall Per Warming
Drawer Requirement
2" (5.1 cm)
Min.
NOTE: install the
oven only with
specific models
Iisted on the labeI
located on top of
the oven.
Per Warming
Drawer
Requirement
Anti-Tip Block
Against Rear
Wall Per
Warming
Drawer
Requirement
2" (5.1 cm)
Min.
1" (2.5 cm) Min. Above Toekick or
Adjust to Oven Installation Height
NOTE: Additional clearances between cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location
do not obstruct the required interior depth and
height.
1"(2,5 cm) Min. Above Toekick
° When installing a Warming Drawer below
a single or double oven, a separate 120V,
60 Hz, properly grounded receptacle must
be installed. Refer to installation instructions
packed with the Warming Drawer for
specific installation requirements.
12

Cabinetry
IAICutoutfor 30"(76.2cm) SingleOvensonly-
BelowanAdvantiumor Betweenan
Advantiumand a Warming Drawer
For JTP30, JTP70, PT916, PT920, ZET938 models only.
Single 30" (76.2 cm)
Oven Below
an Advantium
Single 30" (76.2 cm) Oven
Between an Advantium
and a Warming Drawer
Per Advantiu
Requirement 3" (7.6 cm) Min.
Requirement 3" (7.6 cm) Min.
Note: Install the
oven only with
specific models
listed on the label
located on top of
the oven.
Per Warming
Drawer
Req
2" (5.1 cm) Min.
NOTE: The middle rail separating the two
openings may need to be larger than the 3"
(7.6 cm) minimum shown. Always refer to the
individual installation instructions packed with
each product for specific requirements.
Combined Advantium and Wall
Oven Installation:
When installed in combination with a
single wall oven, use separate electrical
junction boxes.
. Refer to the Advantium oven installation
instructions for electrical requirements of
that product.
. These connections must be made
by a qualified electrician. All electrical
connections must meet National Electrical
Code or prevailing local codes.
NOTE: Additional clearances may be
required. Check to be sure the oven
supports above the Warming Drawer
do not obstruct the required interior depth
and height. The middle rail separating the
openings may need to be larger than the
2" (5.1 cm) minimum shown. Always refer to
the individual installation instructions packed
with each product for specific requirements.
Warming Drawer
Combined with Advantium
and Single Oven:
Install a separate 120V, 60Hz, properly
grounded receptacle. See installation
instructions packed with each product
for specific requirements.
13

Installation Instructions
Electrical Connections
ATTENTION INSTALLER
All electric wall ovens must be hard wired
(direct wired) into an approved junction
box. A plug and receptacle is NOT permitted
on these products.
DO NOT shorten the flexible conduit.
The conduit strain relief clamp must be
securely attached to the junction box
and the flexible conduit must be securely
attached to the clamp. If the flexible
conduit will not fit within the clamp, do not
install the oven until a clamp of the proper
size is obtained.
NOTE TO ELECTRICIAN: The 3 power
leads supplied with this appliance are
UL recognized for connection to heavier
gauge household wiring. The insulation
of these 3 leads is rated at temperatures
much higher than the temperature rating
of household wiring. The current carrying
capacity of the conductor is governed
by the wire gauge and the temperature
rating of the insulation around the wire.
WARNING: Improper
connection of aluminum house
wiring to copper leads can
result in an electrical hazard or fire.
Use only connectors designed for
joining copper to aluminum and follow
the manufacturer's recommended
procedure closely.
Turn off the circuit breaker or remove
fuses to the oven branch circuit.
With the oven supported on a table or
platform in front of the cabinet opening,
connect the flexible conduit to the
electrical junction box as shown below.
Position the conduit in such a manner
that it will lie on top of the oven in
a natural loop when the oven is
installed. You will need to purchase
an appropriate strain relief clamp to
complete the connection of the conduit
to the junction box.
Junction Box
Location
Conduit II
Strain Relief Clamp
_-_ (not included)
must be used at
Junction Box
oven on a
support to assist i
connecting conduit
U
14

Installation Instructions
New Construction and
Four-Conductor Branch
Circuit Connection
•When installing in new construction, or
• When installing in a mobile home, or
• When installing in a recreational vehicle, or
• When local codes do not permit grounding
through neutral:
a. Cut the neutral (white) lead from the crimp.
Re-strip the neutral (white) lead to expose
the proper length of conductor.
.@_ Ground
o,
b. Attach the appliance grounding lead (green
or bare copper) in accordance with local
codes. If the residence grounding conductor
is aluminum, see WARNING on page 14.
c. Connect the oven neutral (white) lead to
the branch circuit neutral (white or gray)
in accordance with local codes, using a
wire nut.
d. Connect the oven red lead to the branch
circuit red lead and the oven black lead to
the branch circuit black lead in accordance
with local codes, using wire nuts. If the
residence red, black or white leads are
aluminum conductors, see WARNING
on page 14.
e. Install Junction Box Cover.
Three-Conductor Branch
Circuit Connection
When connecting to a three-conductor branch
circuit, if local codes permit:
a. Connect the bare oven ground conductor
with the crimped neutral (white) lead to
the branch circuit neutral (white or gray
in color), using a wire nut.
[__ound and
_'-_ II _ Neutral Wires
JcUnTt_onBox
b. Connect the oven red lead to the branch
circuit red lead in accordance with local
codes, using a wire nut.
c. Connect the oven black lead to the branch
circuit black lead in accordance with local
codes, using a wire nut. If the residence
red, black or white leads are aluminum
conductors, see WARNING on page 14.
d. Install Junction Box Cover.
15

Installation Instructions
lclSecuring the Oven in the Opening
I_ Sliding the Oven Into the
Opening
a. Loop (do not tie) a36" (91 cm) string
around the conduit before the oven is slid
into place. This will keep the conduit from
falling behind the oven.
Pull out on
string loop
while pushing
the oven into
the cabinet
b. Lift oven into cabinet cutout using the oven
opening as a grip. Carefully push against
oven front frame. Do not push against
outside edges.
c. As you slide the oven back, pull the string
so that the conduit will lie on top of the
oven in a natural loop.
d. When you are sure the conduit is out of the
way, slide the oven 3/4 way back into the
opening. Remove the string by pulling on
one end of the loop.
Drilling the Pilot Holes and
Mounting the Oven
i
a,
NOTE: Before drilling the pilot holes,
make sure the oven is pushed as far
back into the opening as it will go
and centered.
i
Drill through the mounting holes (top and
bottom) of the side trim, for the #8 screws
provided.
Mounting
Hole
Locations
(Hole
may vary)
1111_
The screws must
be a minimum of
1/4" (6 mm) from
the front of the
cutout.
WARNING: Mounting
screws must be used. Failure to
do so could result in the oven
falling out of the cabinet causing
serious injury.
i
b. Secure the oven to cabinet with screws
provided.
NOTE: If the cabinet is particle board, you
must use #8 x 314" particle board screws.
These may be purchased at any hardware
store.
16

Installation Instructions
Preparing for the Bottom
Trim Installation
a. With oven installed, take the bottom trim
and center it on the bottom front edge of
the cabinet opening.
b. Using the trim
as a template,
mark the center
of each slot
(two total) where
the mounting holes
will be drilled.
c. Remove the trim.
d. Drill pilot holes into
the center of each
template mark.
For 27" (68.6 cm)
Tmi°m_i_p_oitsi_i_o°,_er_jllllllI
Mark (2) Mounting _IIH
Hole Locations _J_i
here
__,2 cm)
*Remove models with
Lower Trim Lower Trim in
Before Position, Mark
Pre-drilling (2) Mounting
Mounting Hole Locations
Holes here
Installing the Metal
Bottom Trim
a. Place the bottom metal trim centered over
the pre-drilled mounting holes. Tape the
edges of the trim down to maintain the
alignment.
b. Using two trim screws provided, secure
the bottom trim to the bottom edge of the
cabinet.
,Side
Lower Trim _, "_'_!,
Side t _I_Y2
Trim Screw Locations for
30" (76.2 cm) models with
Lower Trim
IMPORTANT: If this unit is ever
removed from the cabinet or the oven
is ever pulled out for service, the trim
must be removed first or damage to
the trim will occur.
17

Installation Instructions
151Replacing the Oven Door
NOTE: The oven door is heavy. You
may need help lifting the door high
enough to slide it into the hinge slots.
Do not lift the door by the handle.
i
Lift the oven door by
placing one hand on
each side. The door is
heavy, so you may need
help. Do not lift the door
by the handle.
r-_ With the door at the same angle as
the removal position, which is most of
the way closed, seat the notch of the
hinge arm into the bottom edge of the
hinge slot. The notch of the hinge arm
must be fully seated into the bottom
of the slot.
Hinge Arm
Bottom Edge
of Slot
Hinge Notch
I-_ Open the oven door as far as it
will open.
r-_ Push the hinge locks up against the
front frame of the oven cavity, to the
locked position.
Hinge in
Locked Position
Notch of Hinge
Securely Fitted
into Bottom
Hinge Slot
r-_ Close the oven door.
18

Installation Instructions
Pre-Test Checklist
I_ emove all protective film, if present,
and any stickers.
I_ heck to be sure that all wiring is
secure and not pinched or in contact
with moving parts.
Check that the bottom trim is installed
properly (see page 17).
Check to be sure the mounting screws
are installed and flush with the side trim
(see page 16).
tOperation Checklist
Remove all items from the inside I&_
of the oven.
Check that conduit is securely
connected to the junction box.
Turn on the power to the oven. (Refer
to your Owner's Manual.) Verify that
the bake and broil units, and all
cooking functions operate properly.
Check that the circuit breaker is not
tripped nor the house fuse blown.
See your Owner's Manual for
troubleshooting list.
NOTE TO ELECTRICIAN: The power
leads supplied with this appliance
are UL recognized for connections
to larger gauge household wiring.
The insulation of these leads is
rated at temperatures much higher
than the temperature rating of
household wiring. The current
carrying capacity of a conductor
is governed by the wire gauge and
also the temperature rating of the
insulation around the wire.
NOTE: ALUMINUM WIRING
A. WARNING: IMPROPER
CONNECTION OF ALUMINUM
HOUSE WIRING TO THE COPPER
LEADS CAN RESULT IN AN
ELECTRICAL HAZARD OR FIRE.
B. Splice copper wires to aluminum
wiring using special connectors
designed and UL approved for
joining copper to aluminum,
and follow the manufacturer's
recommended connector
procedure closely.
NOTE: Wire used, location and
enclosure of splices, etc., must
conform to good wiring practice
and local codes.
19

Notes
20