GE CWLSWDMBWF1 User manual

Other manuals for CWLSWDMBWF1

2

This manual suits for next models

1

Table of contents

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Getting started guide

Cisco

Cisco Catalyst X4448 supplementary guide

Compatibility

Requirements

Works

with

C

by

GE

Smart

Lights, Plugs, Switches,

and

Sensors.

Not

compatible

with

non-C

by

GE

Smart

devices.

Note: Switch

and

other

C

by

GE

lights, plugs

and

switches

must

be

grouped

in

the

same

Room/Space

in

the

C

by

GE

opp

to

enable

full

room

control.

3

•••

You

Got

This!

And

we're here

to

help.

For

in-depth

instructional videos

and

a

guided

tour

through

the installation,

go

to

cbyge.com/wirefree-support.

BEFORE

YOU

DO

ANYTHING:

STEP

1

Location &

Mounting Type

Decide

how

you

want

to

mount

your

switch

This switch

can

be

mounted

to

the

wall

in

two

ways,

by

screws

or

adhesive

tape.

Once

you

determine

which install

method

is

best

for

you,

select

one

of

the

following

setup

methods.

For Help,

Go

To:

cbyge.com/wlrefree-support

or

call

1-844-30C-BYGE

7

STEP 2

Installing Your Switch

(mounting with

adhesive

tape)

IMPORTANT Start by removing the clear plastic

tab

from the back

of

the switch.

1.

Identify where you want

to

mount your Wire-Free Switch (switches are

typically located '48-52" from the floor

to

the

top

of

the switch).

2.

Prior

to

installation,

be

sure that the surface

is

smooth

and degreased.

3.

Apply adhesive tape

to

the middle back

of

the switch. Adhesive

tab

should stick out from the side

of

the switch.

This

will be covered

by

the wallplate and allows removal

if

needed in the future.

4. Mount switch to the wall.

5.

Screw on the faceplate bracket, then snap the faceplate cover onto

the bracket.

8 For Help, Go To:

cbyge

.

com/wlrefree-support

or

call 1-84'4-30C-BYGE

STEPS

1,

2 & 3

STEPS

~

& 5

• •

C)

C)

C)

• 0

•

,Q

•

For

Help,

Go

To:

cbyge.com/wlrefree-support

or

call

1-844-30C-BYGE

9

STEP

2

Alternative

Mounting

Installing Your Switch

(mounting with screws/single-gang wallplate)

IMPORTANT Start by removing the clear plastic

tab

from the back

of

the switch.

1.

Identify

where

you

want

to

mount

your

Wire-Free

Switch

(switches

are

typically

located

'48-52"

from

the

floor

to

the

top

of

the

switch).

2.

Mark

the

location

for

holes

to

be

drilled.

We

suggest

using

the

mounting

holes

on

the

switch

housing

as

a

guide.

Use

the

level

(optional)

to

ensure

the

switch is level

before

drilling

holes

.

3. Using 7

/32"

bit

,

drill

holes

in

wall

for

mounting

screws.

Insert

drywall

anchors.

'4.

Secure

the

switch

to

the

wall

until level

and

flush.

5.

Screw

on

the

faceplate

bracket,

then

snap

the

faceplate

cover

onto

the

bracket.

10

For Help,

Go

To:

cbyge

.

com/wlrefree-support

or

call 1-81tle-30C-BYGE