GE IC755CxW07CD SERIES User manual

GE
Intelligent Platforms
GFK-2847F
QuickPanel+ Operator Interface
IC755CxW07CDx (7” Display)
IC755CxS10CDx (10" Display)
IC755CxS12CDx (12” Display)
IC755CxS15CDx (15” Display)
User Manual
For public disclosure

These instructions do not purport to cover all details or variations in equipment, nor to provide for every possible
contingency to be met during installation, operation, and maintenance. The information is supplied for informational
purposes only, and GE makes no warranty as to the accuracy of the information included herein. Changes, modifications,
and/or improvements to equipment and specifications are made periodically and these changes may or may not be reflected
herein. It is understood that GE may make changes, modifications, or improvements to the equipment referenced herein or to
the document itself at any time. This document is intended for trained personnel familiar with the GE products referenced
herein.
This document is approved for public disclosure.
GE may have patents or pending patent applications covering subject matter in this document. The furnishing of this
document does not provide any license whatsoever to any of these patents.
GE provides the following document and the information included therein as is and without warranty of any kind, expressed
or implied, including but not limited to any implied statutory warranty of merchantability or fitness for particular purpose.
For further assistance or technical information, contact the nearest GE Sales or Service Office, or an authorized GE Sales
Representative.
Revised: Sept 2014
Issued: Nov 2013
Copyright © 2013 - 2014 General Electric Company, All rights reserved.
___________________________________
* Indicates a trademark of General Electric Company and/or its subsidiaries.
All other trademarks are the property of their respective owners.
Refer to the section, Contact Information for support on this product.
Please send documentation comments or suggestions to [e-mail]
For public disclosure

Safety Symbol Legend
Warning
Indicates a procedure, condition, or statement that, if not
strictly observed, could result in personal injury or death.
Caution
Indicates a procedure, condition, or statement that, if not
strictly observed, could result in damage to or destruction of
equipment.
Attention
Indicates a procedure, condition, or statement that should be
strictly followed to improve these applications.
For public disclosure

Contact Information
If you purchased this product through an Authorized Channel Partner, then contact the seller directly.
General Contact Information
Online technical support and GlobalCare http://support.ge-ip.com
Additional information http://www.ge-ip.com/
Solution Provider [email protected]
Technical Support
If you have technical problems that cannot be resolved with the information in this manual, please contact us by
telephone or email, or on the web at http://support.ge-ip.com
Americas
Online Technical Support http://support.ge-ip.com
Phone [phone]
International Americas Direct Dial 1-780-420-2010 (if toll free 800 option is unavailable)
Technical Support Email [email protected]
Customer Care Email [email protected]
Primary language of support English
Europe, the Middle East, and Africa
Online Technical Support http://support.ge-ip.com
Phone + 800-1-433-2682
EMEA Direct Dial + 420-23-901-5850 (if toll free 800 option is unavailable or dialing from
a mobile telephone)
Technical Support Email [email protected]
Customer Care Email [email protected]
Primary languages of support English, French, German, Italian, Czech, Spanish
Asia Pacific
Online Technical Support http://support.ge-ip.com
Phone + 86-400-820-8208
+ 86-21-3217-4826 (India, Indonesia, and Pakistan)
Technical Support Email
[email protected] (China)
[email protected] (Japan)
[email protected] (remaining Asia customers)
Customer Care Email
[email protected]
[email protected] (China)
4 GFK-2847F QuickPanel+ Operator Interface User Manual
For public disclosure

Contents
1 Introduction ....................................................................................................................................... 7
1.1 Specifications .........................................................................................................................................7
1.1.1 General Specifications .......................................................................................................................7
1.1.2 Physical Specifications and Mounting Options........................................................................................8
1.1.3 Environmental Specifications ..............................................................................................................9
1.2 QuickPanel+Hardware User Features ........................................................................................................ 10
1.2.1 Physical Overview .......................................................................................................................... 10
1.2.2 Status Indicators ............................................................................................................................. 14
2 Pre-installation Checks................................................................................................................. 15
2.1 Unpacking and Inspection ....................................................................................................................... 15
2.2 Basic Setup .......................................................................................................................................... 17
2.3 Initial Startup........................................................................................................................................ 18
2.3.1 Connecting Input Power ................................................................................................................... 18
2.3.2 Initial Configuration ........................................................................................................................ 19
2.4 Runtime Setup ...................................................................................................................................... 19
2.5 Firmware Updates.................................................................................................................................. 19
2.6 Shutdown............................................................................................................................................. 20
3 Software............................................................................................................................................ 21
3.1 Operating System .................................................................................................................................. 21
3.2 Backup Utility....................................................................................................................................... 21
3.3 Storage Manager ................................................................................................................................... 21
3.4 Copying Project to SD Card..................................................................................................................... 22
3.5 Updating a Machine Edition Project .......................................................................................................... 23
3.6 FTP Server........................................................................................................................................... 24
3.6.1 Authentication of Remote Users......................................................................................................... 24
3.6.2 FTP with Removable Flash Devices ................................................................................................... 24
3.7 HTTP Server ........................................................................................................................................ 25
3.8 SNTP Server......................................................................................................................................... 25
4 Installation........................................................................................................................................ 27
4.1 Installing the Protective Sheet .................................................................................................................. 27
4.2 Choosing a Mounting Location................................................................................................................. 28
4.3 Panel Mounting..................................................................................................................................... 29
4.4 Installation Procedure............................................................................................................................. 31
4.5 Mounting on a VESA Arm ...................................................................................................................... 33
4.6 Installing and Replacing the Battery .......................................................................................................... 34
4.6.1 IC755CxW07CDx........................................................................................................................... 35
4.6.2 IC755CxSxxCDx............................................................................................................................ 37
4.7 Connectors ........................................................................................................................................... 39
4.7.1 Power Connector Pin-out for IC755CxW07CDx and IC755CxSxxCDx ..................................................... 39
4.7.2 Ethernet for IC755CxW07CDx and IC755CxSxxCDx............................................................................ 39
4.7.3 Serial Port ..................................................................................................................................... 40
4.7.4 Universal Serial Bus (USB) Ports....................................................................................................... 44
4.7.5 Audio (LINE OUT) Details for IC755CxW07CDx and IC755CxSxxCDx .................................................. 45
GFK-2847F User Manual 5
For public disclosure

4.7.6 Audio (MIC IN) Details (only applicable to IC755CxW07CDx)............................................................... 45
4.7.7 SD Card Slot.................................................................................................................................. 46
5 Operation.......................................................................................................................................... 47
5.1 Touchscreen Display .............................................................................................................................. 47
5.1.1 Adjusting the Display Brightness ....................................................................................................... 47
5.1.2 Configuring the Backlight................................................................................................................. 47
5.1.3 Re-calibrating the Touchscreen.......................................................................................................... 48
5.2 Keyboard ............................................................................................................................................. 49
5.2.1 External Keyboard (Optional)............................................................................................................ 49
5.2.2 Soft Input Panel.............................................................................................................................. 49
5.3 Mouse ................................................................................................................................................. 49
5.4 Memory............................................................................................................................................... 50
5.4.1 Dynamic RAM Memory................................................................................................................... 50
5.4.2 Modifying Memory Allocation .......................................................................................................... 51
Appendix A Product Certifications and Installation Guidelines............................................... 53
Appendix B Orderable Part Numbers.............................................................................................. 55
Appendix C IC755CxS12CDA Serial Port Details ......................................................................... 57
Index......................................................................................................................................................... 59
6 GFK-2847F QuickPanel+ Operator Interface User Manual
For public disclosure

1 Introduction
The QuickPanel+Operator Interface is an all-in-one microcomputer designed for
maximum flexibility. The design is based on an advanced ARM core microprocessor to
combine a high-resolution touchscreen operator interface with a variety of
communications options. Users can connect to most industrial equipment through the
QuickPanel+communications ports.
The QuickPanel+is equipped with several memory types to satisfy the most demanding
applications. A section of DRAM is split between the operating system, an object store,
and application memory. A section of non-volatile flash memory functioning as a virtual
hard drive is divided between the operating system and persistent storage for application
programs. Retentive memory is a battery-backed SRAM to store and protect valuable data
during a power failure.
1.1 Specifications
1.1.1 General Specifications
Item IC755CxW07CDx IC755CxS10CDx IC755CxS12CDx IC755CxS15CDx
Processor Freescale i.MX535 (1 GHz ARM Cortex A8)
Memory
RAM DDR2 SDRAM
512 MB DDR3 SDRAM 1 GB
ROM SLC NAND 256 MB SLC NAND 512 MB
SRAM 512 KB (with battery backup)
Operating System Microsoft Windows Embedded Compact 7
Display
Type 7" Widescreen TFT
LCD 10.4" Standard TFT LCD 12.1" Standard TFT
LCD
15" Standard TFT
LCD
Resolution 800(W) x 480(H)
pixels WVGA 800(W) x 600(H) pixels SVGA 1024(W) x 768(H) pixels XGA
Color 65,536
Brightness 310 cd/m2400 cd/m2450 cd/m2310 cd/m2
Backlight LED
Touchscreen
Touch Panel
Type Projected capacitive
Multi-touch Two-point
Communi-
cations
Ethernet Port 1x 10/100BaseT
(RJ-45)
2x 10/100BaseT (RJ-45)
1x 10/100BaseT (RJ-45) for IC755CxS12CDA
Serial Port 1x RS-232 UART port
(5-pin connector)
1x RS-232 UART port,
1x RS-232/485 port
(2x 5-pin connector)
(1x 10-pin connector for IC755CxS12CDA)
USB, Host 2x USB 2.0 (Type-A)
Max power (5 V at 0.5 A)
USB, Device 1x USB 2.0 (Mini Type-B)
Storage 1x SD/SDHC card slot
Introduction GFK-2847F User Manual 7
For public disclosure

Item IC755CxW07CDx IC755CxS10CDx IC755CxS12CDx IC755CxS15CDx
Audio
1x Mic In (Mono)
(3.5 mm jack) 1x Line Out (Stereo) (3.5 mm jack)
1x Line Out (Stereo)
(3.5 mm jack)
Noise Immunity
Noise voltage: 1500 V p-p
Pulse duration: 1µs
Rise time: 1ns
Input power
Rated Voltage +24 V dc ±20%
(3-pin connector) +12/24 V dc ±20% (3-pin connector)
Power
Consumption 15 W (max), 0.625 A 18 W (max), 1.5/0.75 A 30 W (max), 2.5/1.25 A
Frame Ground
(FG) Frame GND is connected to Signal GND internally
1.1.2 Physical Specifications and Mounting Options
Item IC755CxW07CDx IC755CxS10CDx IC755CxS12CDx IC755CxS15CDx
Dimensions (L×W×D) 192 × 137 × 36 mm
(7.56 × 5.39 × 1.42 in)
278 × 222 × 65 mm
(10.95 × 8.74 × 2.56 in)
314 × 248 × 65 mm
(12.36 × 9.76 × 2.56 in)
399 × 323 × 70 mm
(15.71 × 12.72 × 2.76 in)
Weight 0.80 kg (1.76 lbs) 2.40 kg (5.29 lbs) 3 kg (6.61 lbs) 4.46 kg (9.83 lbs)
Mounting
Options
Panel cutout
dimensions
183.50 × 128.50 mm
(7.22 × 5.06 in)
266 × 210 mm
(10.47 × 8.27 in)
302 × 228 mm
(11.89 × 8.98 in)
379 × 305 mm
(14.92 × 12.01 in)
VESA
mount
75 x 75 mm
(2.95 x 2.95 in)
100 x 100 mm
(3.94 x 3.94 in)
8 GFK-2847F QuickPanel+ Operator Interface User Manual
For public disclosure

1.1.3 Environmental Specifications
For additional product
standards and agency
approvals, refer to Appendix A.
Note Install the QuickPanel+in a well-ventilated location that is not exposed to dust,
corrosive gases or liquids, rain, strong ultraviolet light or direct sunlight, and meets the
specifications listed in the following table.
Item IC755CxW07CDx IC755CxS10CDx IC755CxS12CDx IC755CxS15CDx
Cooling Natural convection
Ambient Operating
Temperature 0 to +55°C (32 to 131 °F)
Ambient Storage
Temperature -10 to +60°C (14 to 140 °F)
Ambient Humidity
(Operating and
Storage)
85% RH
Non-condensing, wet-bulb temperature: 30°C (86 °F) or less
Environment Pollution Degree 2, Indoor use only
Vibration Resistance
5 to 9 Hz single-amplitude 3.5 mm; 9 to 150 Hz constant-accelerated velocity 9.8 m/s2;
X, Y, Z directions 10 time (100 minutes)
(Compliance 3502, IEC61131-2 JIS B)
Altitude 800~1114 hPa, altitude up to 2000 m (6561.68 ft)
ROHS Compliant with EU RoHS Directive 2011/65/EU
Enclosure Rating IP65 in panel mount
only
UL Type 4X rating;
IP65 in panel mount
only
IP65 in panel mount
only
UL Type 4X rating;
IP65 in panel mount only
Introduction GFK-2847F User Manual 9
For public disclosure

1.2 QuickPanel+Hardware User Features
In addition to the primary touchscreen interface, the QuickPanel+Operator Interface
supports a variety of communication ports.
1.2.1 Physical Overview
The following diagrams display the physical layout of the QuickPanel+, including
locations of status LEDs, communications ports, and connectors.
Battery
Cover
COM
USB Host
Ports
LAN
Input
Power
SD Card
MICRO USB
LINE OUT
MIC IN
Status
Indicator LED
Touchscreen
LCD
IC755CxW07CDx Hardware Features
10 GFK-2847F QuickPanel+ Operator Interface User Manual
For public disclosure

Status
Indicator LED
Touchscreen
LCD
SD Card
USB
Host
Ports
MICRO
USB
LAN2 COM1LAN1 Input
Power
LINE
OUT
COM2
IC755CxS10CDx Hardware Features
Introduction GFK-2847F User Manual 11
For public disclosure















  !  !
IC755CxS12CDx Hardware Features
12 GFK-2847F QuickPanel+ Operator Interface User Manual
For public disclosure

Touchscreen
LCD
Status
Indicator
LED
SD Card
Input
Power
LINE
OUT
USB
Host
Ports
MICRO
USB COM2
LAN2 COM1 LAN1
IC755CxS15CDx Hardware Features
Introduction GFK-2847F User Manual 13
For public disclosure

1.2.2 Status Indicators
The QuickPanel+has a tri-color LED that provides visual status indications for
IC755CxW07CDx and IC755CxSxxCDx units.
1.2.2.1 Status LED Operation
LED State QuickPanel+State
Amber, solid Operating system starting
Green, solid Normal operating state
Green, blinking Backlight off
Red, blinking Backlight failure
Off Power not applied to the unit
1.2.2.2 Ethernet Port LED Operation
The Ethernet port has two LED indicators: Speed and Link Activity.
Speed Link Activity
LED LED State Operating State
Speed On, Yellow 10/100
Link Activity On, Green Link status
14 GFK-2847F QuickPanel+ Operator Interface User Manual
For public disclosure

2 Pre-installation Checks
This chapter provides information for performing a pre-installation check of the
QuickPanel+Operator Interface.
Before installing and using the QuickPanel+, complete the following procedures:
•Unpacking and Inspection
•Basic Setup
•Initial Startup
•Runtime Setup
•Firmware Updates
•Shutdown
2.1 Unpacking and Inspection
Upon receipt of the QuickPanel+Operator Interface, carefully inspect all shipping
containers for damage. If any part of the system is damaged, notify the carrier
immediately. The damaged shipping container should be saved as evidence for inspection
by the carrier. It is the consignee’s responsibility to register a claim with the carrier for
damage incurred during shipment. However, we will fully cooperate should such action
be necessary.
For phone numbers and email
addresses, refer to the section,
Contact Information.
After unpacking the unit, record all serial numbers. Serial numbers are required if you
need to contact Customer Care during the warranty period. Shipping containers and
packing material should be saved in case it is necessary to transport or ship the unit.
Verify that all system components have been received and agree with the order. If the
system received does not agree with your order, contact Customer Care.
Before initial powerup, inspect the unit for loose or damaged components. If damage is
found (such as bent component leads or loose components), contact GE Intelligent
Platforms for additional instructions.
Caution
Do not apply power to the unit if it has visible damage.
Applying power to a unit with damaged components
may cause additional damage.
Pre-installation Checks GFK-2847F User Manual 15
For public disclosure

Battery (Qty 1) (pre-installed)
Serial Port Connector(Qty 1)
Power Connector(Qty 1)
Mounting Brackets(Qty 4)
Protective Sheet (Qty 1) (not shown)
Gasket (Qty 1) (not shown, pre-installed)
QuickPanel+
Operator Interface
IC755CxW07CDx Example Package Contents
16 GFK-2847F QuickPanel+ Operator Interface User Manual
For public disclosure

2.2 Basic Setup
The QuickPanel+Operator Interface is shipped ready for use after initial configuration.
To power up the unit, connect a dc power supply using the supplied quick-connect plug.
Depending on the application, you may also want to connect and configure optional input
devices, communications ports, and expansion adapters.
Warning
ELECTRICAL SHOCK HAZARD — To avoid
personal injury or damage to equipment, ensure that
the dc supply is disconnected from power and that the
leads are not energized before attaching them to the
unit's power supply plug.
Warning
If this equipment is used in a manner not specified by
the manufacturer, the protection provided by the
equipment may be impaired.
Power Supply
Optional Ethernet
Connection
Optional USB Keyboard and Mouse
Serial I/O
Optional Serial I/O
Basic Setup Diagram
Pre-installation Checks GFK-2847F User Manual 17
For public disclosure

2.3 Initial Startup
You will need the following:
• A Safety Extra Low Voltage (SELV) and Limited Energy Circuit or SELV and Class
2 dc power supply.
• The power terminal block is supplied with the product. For voltage and requirements,
refer to the Input Power specifications in the table, General Specifications.
• The mating power terminal block supports stranded 30 – 14 AWG (0.05 – 2.00 mm2)
wires. The user calculates proper gauge wiring for current carrying capacity and loss
according to local regulations.
• At a minimum, the cable must be rated for 75°C (167 °F) or more.
• USB-compatible keyboard (optional)
• USB-compatible mouse (optional)
2.3.1 Connecting Input Power
�� To connect input power
1. Verify that the power cable is not energized.
2. Loosen the screw clamps on the mating power
connector.
3. Strip the insulation from the power cables.
4. Secure the power cable to the mating connector,
noting polarity, and tighten the screw clamps. The
torque for the attaching screws is 0.3 Nm (2.66
in-lb).
5. Apply dc power to the unit. During normal startup
and operation, the QuickPanel+status LED indicator
displays as follows:
•Solid amber while the QuickPanel+is starting
up
•Solid green during normal operation
6. Once power is applied, the QuickPanel+begins
initializing. The first thing to display is the splash
screen.
To skip running any programs included in the
StartUp folder, tap Don’t run Startup programs.
The Microsoft Windows Embedded Compact 7
starts automatically.
M2.5
Mounting clamps M2
Screw clamps
Power Connector
FG GND +24 V dc
18 GFK-2847F QuickPanel+ Operator Interface User Manual
For public disclosure

2.3.2 Initial Configuration
When you first start up the QuickPanel+, a few configuration steps are necessary.
�� To configure the QuickPanel+
1. Tap Start

, point to Settings, then tap Control Panel.
2. From the Control Panel, double-tap Date and Time to configure the system clock.
3. From the Control Panel, double-tap System to configure a Network Device Name.
Many applications, including Proficy Historian, require a unique Device Name.
Attention
It is recommended to set a unique Device Name for
the QuickPanel+to avoid future conflicts.
4. From the Control Panel, double-tap Network and Dial-up Connectionsto
configure network settings.
5. Run the Backup Utility to save the settings.
2.4 Runtime Setup
To download an application to a QuickPanel+Operator Interface, set up a data link
between the unit and your development workstation. Refer to the section Ethernet for
IC755CxW07CDx and IC755CxSxxCDx, and the Proficy Machine Edition (PME) online
help, Downloading a Machine Edition Project.
2.5 Firmware Updates
Update the unit to the most recent released version of the firmware with the latest feature
upgrades and issues addressed. Firmware updates for the QuickPanel+are available on the
Support website.
Pre-installation Checks GFK-2847F User Manual 19
For public disclosure

2.6 Shutdown
There are no specific dangers associated with a power failure or other unplanned
shutdown of the QuickPanel+. In general, programs are retained in flash memory and user
data can be retained in battery-backed SRAM. Some operating system settings are
retained only with user intervention. We recommend the following procedure to shut
down the QuickPanel+.
�� To shut down the QuickPanel+
1. Quit any programs that are running and wait for all file operations to complete.
2. If you have not changed operating system settings (for example, brightness or
touchscreen sensitivity) or do not want to save the changes, remove ac power from
the dc supply.
3. To save changes to operating system settings run Backup. When the Backup dialog
box displays Completed Successfully, remove power from the dc power supply
connected to the QuickPanel+.
20 GFK-2847F QuickPanel+ Operator Interface User Manual
For public disclosure