GEA VARIVENT User manual

Hygienic valves
GEA VARIVENT® control valve type P
Operating instruction (Translation from the original language)
430BAL011665EN_5

COPYRIGHT
These Operating Instructions are the English translation of the original operating
instructions in the sense of the EU Machinery Directive. This document is
protected by copyright. All rights reserved. The document may not, in whole or in
part, be copied, reproduced, translated or reduced to an electronic medium of
machine-readable form without the express permission of GEA Tuchenhagen
GmbH.
LEGAL NOTICE
Word marks
The designations VARIVENT® and T.VIS® are protected trademarks of GEA
Tuchenhagen GmbH.
430BAL011665EN_5
2 21.03.2023

TABLE OF CONTENTS
1 General Information 5
1.1 Information on the Document 5
1.1.1 Binding Character of These Operating Instructions 5
1.1.2 Notes on the Illustrations 5
1.1.3 Symbols and Highlighting 5
1.2 Manufacturer address 6
1.3 Contact 6
1.4 EU Declaration of Conformity in accordance with the EC Machinery Directive 2006/42/EC 7
2 Safety 8
2.1 Intended use 8
2.1.1 Requirements for operation 8
2.1.2 Pressure equipment directive 8
2.1.3 ATEX directive 8
2.1.4 Improper operating conditions 8
2.2 Operator’s Duty of Care 9
2.3 Subsequent changes 10
2.4 General safety instructions and dangers 10
2.4.1 Principles for safe operation 10
2.4.2 Environmental Protection 10
2.4.3 Electrical Equipment 11
2.5 Supplementary Regulations 11
2.6 Qualification of personnel 11
2.7 Safety equipment 13
2.7.1 Signage 13
2.8 Residual dangers 13
2.9 Danger zones 14
3 Description 17
3.1 Design 17
3.2 Functional description 19
3.2.1 Control valve type P- P_F / P_J 19
3.2.2 Control valve type P - divert valve W/X 20
4 Transport and storage 21
4.1 Storage conditions 21
4.2 Transport 21
4.2.1 Scope of supply 22
5 Technical data 23
5.1 Type plate 23
5.2 Technical data 24
5.3 Seat leakage according to DIN EN 60534-4 25
5.4 Resistance and permitted operating temperature of the sealing materials 26
5.5 Pipe ends - General table of measurements 27
5.6 Tools 29
5.7 Lubricants 29
5.8 Weights 29
6 Assembly and installation 30
6.1 Safety instructions 30
6.2 Notes on installation 30
6.3 Control head 30
6.4 Valve with Detachable Pipe Connection Elements 30
6.5 Valve with Welded Ends 31
6.6 Pneumatic connections 32
6.6.1 Air Requirement 32
6.6.2 Establishing Hose Connections 32
6.7 Electrical connection with T.VIS control top 33
7 Start-up 34
7.1 Safety instructions 34
7.2 Notes on commissioning 34
8 Operation and control 35
8.1 Safety instructions 35
430BAL011665EN_5
21.03.2023 3

9 Cleaning 36
9.1 Cleaning 36
9.1.1 Cleaning Process Examples 36
9.1.2 Cleaning effect 36
9.2 Passivation 37
10 Maintenance 38
10.1 Safety instructions 38
10.2 Inspections 39
10.2.1 Product contact seals 39
10.2.2 Pneumatic connections 39
10.2.3 Electrical connections 39
10.3 Maintenance intervals 40
10.4 Prior to disassembly 40
10.5 Disassembly 40
10.5.1 Disassembling Control Valve Type P-P_F / P_J / Disassembling Control Valve Type P - 3-Stage Seat K 41
10.5.2 Control Valve Type P - Disassembling Divert Valve W 47
10.5.3 Control Valve Type P - Disassembling Divert Valve X 53
10.6 Maintenance 59
10.6.1 Cleaning the Valve 59
10.6.2 Replacing Seals 60
10.6.3 Lubricating Seals and Threads 61
10.7 Installation 62
10.7.1 Installing the valve 62
10.7.2 Torques for the Clamps and Clamp Connections 63
10.7.3 Checking the function 64
11 Alarms 66
11.1 Malfunctions and remedies 66
12 Decommissioning 67
12.1 Safety instructions 67
12.2 Disposal 67
12.2.1 General notes 67
12.2.2 Valve Actuator Disposal 67
13 Spare parts list - VARIVENT control valve type P P_F/P_J 68
14 Spare parts list - VARIVENT control valve type P, divert valve W/X 102
15 Spare parts list - VARIVENT control valve type P 3-stage seat K 107
16 Dimensions sheet - VARIVENT control valve type P P_F/P_J 112
17 Dimensions sheet - VARIVENT control valve type P, divert valve W/X 114
18 Dimensions sheet - VARIVENT control valve type P 3-stage seat K 116
19 Appendix 118
19.1 Lists 118
19.1.1 Abbreviations and terms 118
430BAL011665EN_5
4 21.03.2023

1 General Information
1.1 Information on the Document
The present Operating Instructions are part of the user information for the
product. The Operating Instructions contain all the information you need to
transport, install, commission, operate and carry out maintenance for the product.
1.1.1 Binding Character of These Operating Instructions
These Operating Instructions contain the manufacturer's instructions to the
operator of the product and to all persons who work on or use the product
regarding the procedures to follow.
Carefully read these Operating Instructions before starting any work on or using
the product. Your personal safety and the safety of the product can only be
ensured if you act as described in the Operating Instructions.
Store the Operating Instructions in such a way that they are accessible to the
operator and the operating staff during the entire life cycle of the product. When
the location is changed or the product is sold make sure you also provide the
Operating Instructions.
1.1.2 Notes on the Illustrations
The illustrations in these Operating Instructions show the product in a simplified
form. The actual design of the product can differ from the illustration. For detailed
views and dimensions of the product please refer to the design documents.
1.1.3 Symbols and Highlighting
In these Operating Instructions, important information is highlighted by symbols
or special formatting. The following examples illustrate the most important types
of highlighting.
Danger
Warning: Fatal Injuries
Failure to observe the warning can result in serious damage to health, or
even death.
► The arrow identifies a precautionary measure you have to take to avoid
the hazard.
Warning: Explosions
Failure to observe the warning can result in severe explosions.
► The arrow identifies a precautionary measure you have to take to avoid
the hazard.
General Information
Information on the Document
430BAL011665EN_5
21.03.2023 5

Warning!
Warning: Serious Injuries
Failure to observe the warning can result in serious damage to health.
► The arrow identifies a precautionary measure you have to take to avoid
the hazard.
Caution!
Warning: Injuries
Failure to observe the warning can result in minor or moderate damage to
health.
► The arrow identifies a precautionary measure you have to take to avoid
the hazard.
Notice
Warning: Damage to Property
Failure to observe the warning can result in serious damage to the
component or in the vicinity of the component.
► The arrow identifies a precautionary measure you have to take to avoid
the hazard.
Carry out the following steps: = Start of a set of instructions.
1. First step in a sequence of operations.
2. Second step in a sequence of operations.
®Result of the previous operation.
®The operation is complete, the goal has been achieved.
Hint!
Further useful information.
1.2 Manufacturer address
GEA Tuchenhagen GmbH
Am Industriepark 2-10
21514 Büchen
1.3 Contact
Tel.:[phone]
Fax:[phone]
[email protected]
www.gea.com
General Information
Manufacturer address
430BAL011665EN_5
6 21.03.2023

1.4 EU Declaration of Conformity in accordance with the EC Machinery Directive
2006/42/EC
Manufacturer: GEA Tuchenhagen GmbH
Am Industriepark 2-10
21514 Büchen
We hereby declare that the machine named below
Designation: Valve with actuator
Type: VARIVENT®
due to its design and construction as well as in the versions sold by us, meet the basic safety and health
requirements of the following guideline:
Relevant EC directives: 2006/42/EC EC Machinery Directive
Applicable harmonized standards,
in particular:
EN ISO 12100: 2010
Remarks: •This declaration will become invalid if any
alterations are made to the machine which have
not been agreed with us
•We also declare that the relevant technical
documentation for this machine has been
prepared in accordance with Annex VII, Part A,
and agree to submit the documentation on
justified request of national authorities on a data
carrier
Person authorised for compilation and handover of
technical documentation:
GEA Tuchenhagen GmbH
CE Documentation Officer
Am Industriepark 2-10
21514 Büchen, Germany
Büchen, 24 January 2020
Franz Bürmann
Managing Director i.V. Matthias Südel Head of Engineering
General Information
EU Declaration of Conformity in accordance with the EC Machinery Directive 2006/42/EC
430BAL011665EN_5
21.03.2023 7

2 Safety
2.1 Intended use
The control valve is used to control flow rates and pressures in automated
process plants.
The medium should preferably flow in the opening direction of the valve disk to
avoid pipe hammers when the valve is opened or closed.
Hint!
The manufacturer will not accept any liability for damage resulting
from any use of the valve which is not in accordance with the
designated use of the valve. The risk of such misuse lies entirely with
the operator of the facility.
2.1.1 Requirements for operation
The prerequisite for reliable and safe operation of the component is proper
transportation and storage as well as professional installation and assembly.
Operating the unit within the limits of its designated use also involves adhering to
the operating, inspection and maintenance instructions.
2.1.2 Pressure equipment directive
The valve is a piece of pressure equipment (without safety function) in the sense
of the pressure equipment directive 2014/68/EU: Classified according to Annex II
in category 1.
According to the scope of directive 2014/34/EC, article 1, paragraph 2, f, the
exception of the directive applies, due to conformity with the machine directive
2006/42/EU.
The nominal diameters smaller than DN 25 are subject to article 4, paragraph 3
of the Pressure Equipment Directive which specifies sound engineering practice.
Nominal diameters ≥ IPS 4“; DN 125 valid for the fluid group II.
In the event of any deviations, GEA Tuchenhagen GmbH will supply a specific
Declaration of Conformity.
2.1.3 ATEX directive
If the control valves are used in areas with a potentially explosive atmosphere,
you must absolutely comply with directive 2014/34/EU with respect to all ignition
hazards.
The supplementary ATEX operating instructions for VARIVENT valves must be
observed. For details regarding the marking of valves for potentially explosive
areas also refer to the additional ATEX operating instructions for VARIVENT
valves.
If used in explosion-proof areas, the regulations laid down in the European
standards DIN EN 60079-0 and DIN EN 60079-11 must be observed.
2.1.4 Improper operating conditions
Safety
Intended use
430BAL011665EN_5
8 21.03.2023

The operational safety of the component can not be guaranteed under improper
operating conditions. Therefore avoid improper operating conditions.
The operation of the component is not permitted if:
•Persons or objects are in the danger zone.
•Safety devices are not working or were removed.
•Malfunctions have been detected on the component.
•Damage to the component has been detected.
•Maintenance intervals have been exceeded.
2.2 Operator’s Duty of Care
The operating company of the component has a special responsibility for the
proper and safe handling of the component within their company. Only use the
component when it is in perfect operating condition in order to prevent danger to
persons and property.
This operating manual contains information that you and your employees need
for safe operation over the life of the component. Be sure to read these Operating
Instructions carefully and ensure that the measures described here are observed.
The operator's duty of care includes planning the necessary safety measures and
monitoring that these measures are observed. The following principles apply:
•Only qualified personnel may work on the component.
•The operating company must authorize personnel to carry out the relevant
tasks.
•Order and cleanliness must be maintained at the work stations and in the
entire area surrounding the component.
•Personnel must wear suitable work clothing and personal protective
equipment. As the operating company must ensure that work clothing and
personal protective equipment are used.
•Inform personnel regarding any properties of the product which might pose a
health risk and the preventative measures to be taken.
•Have a qualified first-aid representative on call during the operation. This
person must be able to initiate any necessary first-aid measures in case of an
emergency.
•Clearly define procedures, competences and responsibilities for those
working in the area of the component. Everybody must know what to do in
case of an emergency. Instruct the staff in this respect at regular intervals.
•The signs on the component must always be complete and easy to read.
Check, clean and replace the signs as necessary at regular intervals.
•Observe the Technical Data specified and the limits of use!
Safety
Operator’s Duty of Care
430BAL011665EN_5
21.03.2023 9

Hint!
Carry out regular checks. This way you can ensure that these
measures are actually observed.
2.3 Subsequent changes
No technical modifications should ever be made to this component. Otherwise
you will have to undergo a new conformity process in accordance with the EC
Machinery Directive on your own.
In general, only original spare parts supplied by GEA Tuchenhagen GmbH
should be fitted. This ensures that the component is always operating properly
and efficiently.
2.4 General safety instructions and dangers
The component is safe to operate. It was built according to state-of-the-art
science and technology.
Nevertheless, dangers can arise from the component, if:
•the component is not used as intended
•the component is used improperly
•the component is operated under impermissible conditions
2.4.1 Principles for safe operation
Dangerous situations during operation can be avoided by safety-conscious and
proactive behaviour of the staff.
To ensure safe operation of the valve the following principles apply:
•The Operating Instructions must be kept ready to hand at the valve's place of
use. They must be complete and in clearly legible form.
•Only use the valve for its intended use.
•The valve must be functional and in good working order. Check the condition
of the valve before starting work and at regular intervals.
•Wear tight-fitting work clothing for all work on the valve.
•Ensure that nobody can get hurt on the parts of the valve.
•Immediately report any faults or noticeable changes on the valve to the
person responsible.
•Never touch the pipes and the valve when these components are hot! Avoid
opening the valve unless the process plants have been emptied and
depressurised.
•Observe the accident prevention regulations and all local regulations.
2.4.2 Environmental Protection
Harm to the environment can be avoided by safety-conscious and proactive
behaviour of the staff.
Safety
Subsequent changes
430BAL011665EN_5
10 21.03.2023