gefran ADV200 WA Parts list manual

.... Functions description
and parameters list
Field oriented
vector AC Drive
ADV200 WA
Industrial application

2 ADV200 WA • Functions description and parameters list
Information about this manual
This manual explains the functions and the description of the parameters.
The informations about mechanical installation, electrical connection and fast start-up can be found on the
ADV200 Quick start guide.
The whole set of manuals (included the expansions and eld bus manuals) can be found on Gefran web site.
Software version
This manual is updated according the software version V 2.X.1
The identication number of the software version is indicated on the identication plate of the drive or can be
checked with the Firmware ver.rel - PAR 490 parameter, menu 2.5.
General information
Note ! In industry, the terms “Inverter”, “Regulator” and “Drive” are sometimes interchanged. In this document, the term “Drive” will be
used.
Before using the product, read the safety instruction section carefully. Keep the manual in a safe place and
available to engineering and installation personnel during the product functioning period.
Gefran S.p.A has the right to modify products, data and dimensions without notice. The data can only be used
for the product description and they can not be understood as legally stated properti
Thank you for choosing this Gefran product.
We will be glad to receive any possible information which could help us improvingthis manual. The e-mail ad-
dress is the following: [email protected].
All rights reserved
Symbols used in the manual
Indicates a procedure, condition, or statement that, if not strictly observed, could result in personal injury or
death.
Indique le mode d’utilisation, la procédure et la condition d’exploitation. Si ces consignes ne sont passtricte-
ment respectées, il y a des risques de blessures corporelles ou de mort.
Indicates a procedure, condition, or statement that, if not strictly observed, could result in damage to or de-
struction of equipment.
Indique et le mode d’utilisation, la procédure et la condition d’exploitation. Si ces consignes ne sont pas stric-
tement respectées, il y a des risques de détérioration ou de destruction des appareils.
Indicates that the presence of electrostatic discharge could damage the appliance. When handling the boards,
always wear a grounded bracelet.
Indique que la présence de décharges électrostatiques est susceptible d’endommager l’appareil. Toujours
porter un bracelet de mise à la terre lors de la manipulation des cartes.
Indicates a procedure, condition, or statement that should be strictly followed in order to optimize these applica-
tions.
Indique le mode d’utilisation, la procédure et la condition d’exploitation. Ces consignes doivent êtrerigoureu-
sement respectées pour optimiser ces applications.
Note ! Indicates an essential or important procedure, condition, or statement.
Indique un mode d’utilisation, de procédure et de condition d’exploitation essentiels ou importants
Warning
Caution
Important

ADV200 WA • Functions description and parameters list 3
Table of Contents
Information about this manual..................................................................................................................2
Symbols used in the manual...................................................................................................................................2
A – Programming .......................................................................................................................................5
A.1 Menu display modes ........................................................................................................................................5
A.2 Programming of “function block” analog and digital input signals ....................................................................5
A.3 Variable interconnections mode .......................................................................................................................5
B – Parameters and functions description (Expert list) .........................................................................7
Legend....................................................................................................................................................................7
1 – MONITOR.........................................................................................................................................................8
2 – DRIVE INFO ...................................................................................................................................................11
3 – STARTUP WIZARD ........................................................................................................................................14
4 – DRIVE CONFIG..............................................................................................................................................15
5 – REFERENCES ...............................................................................................................................................20
6 – RAMPS...........................................................................................................................................................25
7 – MULTI REFERENCE ......................................................................................................................................28
8 – MOTORPOTENTIOMETER ...........................................................................................................................31
9 – JOG FUNCTION.............................................................................................................................................37
10 – MONITOR FUNCTION .................................................................................................................................38
11 – COMMANDS.................................................................................................................................................42
12 – DIGITAL INPUTS.........................................................................................................................................50
13 – DIGITAL OUTPUTS......................................................................................................................................52
14 – ANALOG INPUTS.........................................................................................................................................54
15 – ANALOG OUTPUTS ....................................................................................................................................62
16 – MOTOR DATA...............................................................................................................................................67
18 – SPEED REG GAINS.....................................................................................................................................71
19 – REGULATOR PARAM ..................................................................................................................................74
21 – FV PARAMETERS........................................................................................................................................77
22 – FUNCTIONS.................................................................................................................................................82
22.1 – FUNCTIONS/SPEED RATIO................................................................................................................................................................ 82
22.2– FUNCTIONS/INERTIA COMP .............................................................................................................................................................. 83
22.3– FUNCTIONS/DC BRAKING ................................................................................................................................................................. 84
22.4– FUNCTIONS/MOTOR OVERLOAD ..................................................................................................................................................... 87
22.5– FUNCTIONS/BRES OVERLOAD......................................................................................................................................................... 90
22.6– FUNCTIONS/SPEED CAPTURE ......................................................................................................................................................... 91
22.7– FUNCTIONS/POWER LOSS................................................................................................................................................................ 94
22.8– FUNCTIONS/COMPARE.................................................................................................................................................................... 101
22.9– FUNCTIONS/PADS ............................................................................................................................................................................ 103
22.10- FUNCTIONS/VDC CONTROL .......................................................................................................................................................... 104
22.11- FUNCTIONS/BRAKE CONTROL...................................................................................................................................................... 105
22.12 - FUNCTIONS/VF ENERGY SAVE ..................................................................................................................................................... 106
22.13 - FUNCTIONS/RTC_SET .................................................................................................................................................................... 108
23 – COMMUNICATION.....................................................................................................................................109
23.1 – COMMUNICATION/RS485................................................................................................................................................................. 109
23.2 – COMMUNICATION/FIELDBUS CONFIG ...........................................................................................................................................110
23.3 – COMMUNICATION/FIELDBUS M->S .................................................................................................................................................111
23.4 – COMMUNICATION/FIELDBUS S->M..................................................................................................................................................116
23.5 – COMMUNICATION/WORD COMP......................................................................................................................................................119
23.6 – COMMUNICATION/WORD DECOMP................................................................................................................................................ 120
24 – ALARM CONFIG.........................................................................................................................................121
25 – ALARM LOG ...............................................................................................................................................133
26 - PROCESS...................................................................................................................................................134
26.1 - PROCESS/PID 1 REFERENCES ....................................................................................................................................................... 134
26.2 – PROCESS/ PID 1 ............................................................................................................................................................................... 138
26.3 – PROCESS/PID 2 REFERENCES....................................................................................................................................................... 143
26.4 – PROCESS/ PID 2 ............................................................................................................................................................................... 147
26.5 – PROCESS/SLEEP MODE.................................................................................................................................................................. 150
26.6 – PROCESS/FLOW COMPENS............................................................................................................................................................ 153
26.7 – PROCESS/FILL.................................................................................................................................................................................. 155
26.8 – PROCESS/MIN FREQUENCY........................................................................................................................................................... 157
26.9 – PROCESS/CHECK VALVE ................................................................................................................................................................ 158
26.10 – PROCESS/PUMP CLEAN................................................................................................................................................................ 159
26.11 – PROCESS/LOW POWER CALC...................................................................................................................................................... 162
26.13 – PROCESS/TIMERS.......................................................................................................................................................................... 165
26.14 – PROCESS/MULTI PUMP ................................................................................................................................................................. 171
27 – MULTIDRIVE ..............................................................................................................................................177
27.1 SETTINGS............................................................................................................................................................................................. 180
27.2 I/O CONTROLLER ............................................................................................................................................................................... 182
27.3 SEQUENCES ........................................................................................................................................................................................ 183
27.4 I/O FOLLOWER ................................................................................................................................................................................... 184
27.5 TIMER................................................................................................................................................................................................... 186
27 – MACRO ......................................................................................................................................................187
27.1 – MACRO Selection............................................................................................................................................................................... 187
27.2 – HVAC Standard .................................................................................................................................................................................. 188
27.3 – Supply FAN......................................................................................................................................................................................... 191
27.4 – Return FAN......................................................................................................................................................................................... 194

4 ADV200 WA • Functions description and parameters list
27.5 – Cooling Tower..................................................................................................................................................................................... 197
27.6 – Condenser .......................................................................................................................................................................................... 200
27.7 – Booster Pump..................................................................................................................................................................................... 203
PARAMETERS ON SELECTION LISTS, BUT NOT DISPLAYED ON KEYPAD ...............................................206
C - Parameter List (Expert)....................................................................................................................214
D – SELECTION LISTS...........................................................................................................................262
L_ANOUT ...................................................................................................................................................................................................... 262
L_CMP........................................................................................................................................................................................................... 262
L_DIGSEL1.................................................................................................................................................................................................... 262
L_DIGSEL2.................................................................................................................................................................................................... 263
L_DIGSEL3.................................................................................................................................................................................................... 263
L_DIGSEL4.................................................................................................................................................................................................... 264
L_FBS2M....................................................................................................................................................................................................... 264
L_LIM............................................................................................................................................................................................................. 264
L_MLTREF..................................................................................................................................................................................................... 265
L_PIDFBK ..................................................................................................................................................................................................... 265
L_PIDREF ..................................................................................................................................................................................................... 265
L_REF............................................................................................................................................................................................................ 265
L_SCOPE ...................................................................................................................................................................................................... 266
L_VREF ......................................................................................................................................................................................................... 266
L_WDECOMP................................................................................................................................................................................................ 266
E – TROUBLESHOOTING - Alarms.......................................................................................................267
F – MESSAGES.......................................................................................................................................270
G - Block Diagrams................................................................................................................................274
System Diagrams Index......................................................................................................................................274
Drive overview ....................................................................................................................................................274
References .........................................................................................................................................................275
Ramps ................................................................................................................................................................276
Multireference.....................................................................................................................................................276
Motorpotentiometer.............................................................................................................................................277
Jog function ........................................................................................................................................................277
Monitor function ..................................................................................................................................................278
Commands .........................................................................................................................................................280
Digital inputs .......................................................................................................................................................282
Digital outputs.....................................................................................................................................................283
Analog inputs......................................................................................................................................................284
Analog outputs....................................................................................................................................................286
Speed reg gains..................................................................................................................................................287
VF parameters....................................................................................................................................................288
Functions ............................................................................................................................................................289
Process...............................................................................................................................................................293

ADV200 WA • Functions description and parameters list 5
A – Programming
A.1 Menu display modes
The programming menu can be displayed in two modes, which can be selected using the Access mode
parameter (04 - DRIVE CONFIG menu):
• Easy (default) only the main parameters are displayed.
• Expert all the parameters are displayed
A.2 Programming of “function block” analog and digital input signals
The signals, variables and parameters of each single “function block” of the drive are interconnected in order
to achieve the congurations and controls inside the control system.
These can be managed and modied using the keypad, PC congurator or eldbus programming.
The programming mode is based on the following logic:
Src (source; i.e.: Ramp ref 1 src, PAR: 610)
This term denes the source of the function block input, i.e. the signal to be processed in the
function block.
The different congurations are dened in the relative selection lists
.
cfg (conguration; i.e.: Mpot init cfg, PAR: 880)
This term refers to the parameter setting and its effect on the function block.
For example: Ramp times, internal reference adjustment, etc...
mon (display; i.e.: Ramp ref 1 mon, PAR: 620)
This term refers to the variable output from the function block, which is the result of the
calculations performed on the actual block
.
Input selected
Parameter
Parameter
Parameter
Variable
Cfg
src Monitor
Function block
A.3 Variable interconnections mode
The source (src) allows the desired control signal to be assigned to the function block input.
This operation is performed by using specic selection lists.
Possible control signal sources:
1 – Physical terminal
The analog and digital signals come from the terminal strip of the regulation card and/or from those of the
expansion cards.
2 – Drive internal variables
Internal drive control system variables, from “function block” calculations, sent via keypad, PC congurator or
eldbus.

6 ADV200 WA • Functions description and parameters list
Practical example
The following examples illustrate the philosophies and methods with which more or less complex operations
are performed in the single “function blocks”, the results of which represent the output of the block.
• Example: Changing the Speed Reference source
The main drive reference (in the default conguration) Ramp ref 1 mon (PAR: 620) is generated by the output
of the function block “Ramp setpoint Block”.
Its default source is the Analog input 1 mon signal (PAR: 1500), from the output of the function block
“Analog input 1 Block”, which in this case refers to analog input 1 of the signal terminal strip.
To change the reference source from the analog input to a digital reference inside the drive, the input signal
must be changed to “Ramp setpoint Block”.
Enter the Ramp ref 1 src parameter (PAR: 610) and set a new reference, selecting it from among those listed
in the L_MLTREF selection list, for example Dig ramp ref 1 (PAR: 600).
• Example: Inverting the analog reference signal
To invert the “Analog input 1 Block” output signal, the value of the An inp 1 sign src parameter (PAR:
1526), which has a default setting of Null (no operation), must be changed by selecting the source of the
command signal from among those listed in the L_DIGSEL 2 selection list, for example Digital input X mon,
One (function always enabled), etc.
+1
-1
*-1
*+1
Null
Null
An inp1sign src
Null An inp1alt sel src
Analog input1mon
Analog input1Block
Ramp Setpoint Block
Terminal input
Ramp ref 1mon
Ramp ref 1 src
An inp1alt value
Ramp ref invert src
The diagrams above illustrate the internal processing philosophy of the single “function blocks” and the result
of these changes on the other interconnected “function blocks”.
Note ! This section contains a brief description of the functions of the other parameters in the function blocks not included for the
changes in the example
The An inp 1 alt sel src parameter (PAR: 1528) can be used to select an alternative reference for the Analog
input 1 mon (PAR: 1500) output.
The An inp 1 alt value parameter (PAR: 1524) determines the alternative reference value for the Analog
input 1 mon (PAR: 1500) output.
The Ramp ref invert src parameter (PAR: 616) can be used to select the source for the command to reverse
the “Ramp setpoint” function block output.
The output signal from the “Ramp setpoint” block is displayed in the Ramp ref 1 mon parameter (PAR: 620).

ADV200 WA • Functions description and parameters list 7
B – Parameters and functions description (Expert list)
Legend
          
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
1 - MONITOR
1.1 250 Output current A FLOAT 16/32 0.0 0.0 0.0 R VS
1.2 252 Output voltage V FLOAT 16/32 0.0 0.0 0.0 R VS
22.1 - FUNCTIONS/SPEED RATIO
22.1.1 3000 Dig speed ratio perc INT16 16/32 100 CALCI CALCI ERW VS
22.1.2 3002 Speed ratio src LINK 16/32 3000 0 16384 ERW VS
L_VREF( Selection List ) [*]
( Level 1 menu )
( Level 2 menu )
Indexing of the menu and parameter
Parameter identifier
Parameter description
UM: unit of measure

Type of parameter
BIT Boolean, from modbus seen as 16 bits
ENUM Selection list, from modbus seen as 16 bits
FLOAT Real, from modbus seen as 32 bits
FBM2SIPA 16-bit unsigned integer. Only PAR of existing
parameters accepted.
FBS2MIPA 16-bit unsigned integer. Only PAR of existing
parameters accepted.
INT16 Integer with sign 16 bits, from modbus seen as 16 bits
INT32 Integer with sign 32 bits, from modbus seen as 32 bits
ILINK Selection list, from modbus seen as 16 bits
LINK Selection list, from modbus seen as 16 bits
UINT16 Integer without sign 16 bits, from modbus seen as
16 bits
UINT32 Integer without sign 32 bits, from modbus seen as
32 bits
Format of data exchanged on Fieldbus (16BIT, 32BIT)
Default value CALCF Value calculated as a number with
floating point
CALCI Value calculated as a whole num-
ber (Max = 32768)
SIZE Value depending on the size of the
drive
Minimum value
Maximum value

Accessibility :
E Expert
R Read
S Size (set value depending on the size of the device)
W Write
Z parameters that can be modified ONLY with the drive disa-
bled

Available in regulation mode:
V = V/f Control
S = Vect Flux OL
[*]
Selection lists:
The “... src” format parameters are linked to a selection list.
The source of the signal that will control the parameter can be
selected from the list indicated.
The lists are indicated in paragraph C of this manual.

8 ADV200 WA • Functions description and parameters list
1 – MONITOR
The monitor menu displays the measured values of the sizes and of the drive operating parameters.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
1.1 250 Output current A FLOAT 16/32 0.0 0.0 0.0 R VS
The drive output current is displayed.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
1.2 252 Output voltage V FLOAT 16/32 0.0 0.0 0.0 R VS
The drive line voltage output is displayed.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
1.3 254 Output frequency Hz FLOAT 16/32 0 0 0 R VS
The drive output frequency is displayed.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
1.4 256 Output power kW FLOAT 16/32 0.0 0.0 0.0 R VS
Displays the drive output power.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
1.5 628 Ramp setpoint rpm INT16 16/32 0 0 0 R VS
The ramp reference is displayed. This is the speed value the drive must reach at the end of the ramp.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
1.6 664 Speed setpoint rpm INT16 16/32 0 0 0 R VS
The speed reference is displayed. This is the value measured at the output of the speed reference circuit.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
1.7 260 Motor speed rpm INT16 16/32 0 0 0 R VS
The actual output speed of the motor is displayed (in Flux vector OL/V/f control = speed estimated by the
drive).
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
1.8 270 DC link voltage V FLOAT 16/32 0.0 0.0 0.0 ER VS
The direct voltage of the intermediate circuit capacitors is displayed (DC-Bus).

ADV200 WA • Functions description and parameters list 9
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
1.9 272 Heatsink temperature degC INT16 16 0 0 0 ER VS
The temperature measured on the drive heatsink is displayed.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
1.10 290 Motor temperature degC FLOAT 0.0 0.0 0.0 ER VS
The motor temperature measured by the PT100 probes. The temperature can only be measured correctly if
just one temperature sensor is connected.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
1.11 280 Torque current ref A FLOAT 16/32 0.0 0.0 0.0 ER _S
The current reference used for torque control is displayed (in the Flux vector OL mode).
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
1.12 282 Magnet current ref A FLOAT 16/32 0.0 0.0 0.0 ER _S
The magnetizing current reference is displayed (in the Flux vector OL mode).
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
1.13 284 Torque current A FLOAT 16/32 0.0 0.0 0.0 ER VS
The actual torque current value is displayed.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
1.14 286 Magnet current A FLOAT 16/32 0.0 0.0 0.0 ER VS
The actual magnetizing current value is displayed.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
1.15 3212 Motor overload accum perc UINT1616/32 0 0 100 ER VS
The motor overload level is displayed (100% = alarm threshold).
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
1.16 368 Drive overload accum perc UINT1616/32 0 0 100 ER VS
The drive overload level is displayed. An instantaneous overload of 180% of the drive rated current is al-
lowed for 0.5s. The thermal image I²t adjusts the drive output current thresholds. During normal operation, the
instantaneous output current value can reach 180% of the drive rated current. After 0.5s at 180%, the output
current threshold is reduced to 150%. When the overload level par. 368 Drive overload accum reaches
100%, the output current threshold is reduced to 100% of the rated current, and stays at that value until the I²t
integrator cycle is complete. At this point the 180% instantaneous overload is re-enabled.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
1.17 3260 Bres overload accum perc UINT1616/32 0 0 100 ER VS
The braking resistor overload limit is displayed (100% = alarm threshold).
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
1.18 1066 Enable state mon BIT 16 0 0 1 R VS
The drive Enable command status is displayed. Voltage must be present on terminal 7. The FR Forwardstart
command is needed to start the inverter.
0 Disabled drive disabled
1 Enabled drive enabled
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
1.19 1068 Start state mon BIT 16 0 0 1 R VS
The drive Start command status is displayed.

10 ADV200 WA • Functions description and parameters list
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
1.20 1070 FastStop state mon BIT 16 0 0 1 R VS
The drive FastStop command status is displayed.
Menu PAR Descripttion UM Type FB BIT Def Min Max Acc Mod
1.21 1100 Digital input mon UINT16 16 0 0 0 R VS
The status of the digital inputs on the drive is displayed. It can also be read via a serial line or eldbus. The
data are contained in a word, where each bit is 1 if voltage is supplied to the corresponding input terminal.
1Input enabled.
0Input disabled.
I.e. :
00000000001
1
Attivo DI 1Attivo DI 2
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
1.22 1300 Digital output mon UINT16 0 0 0 R VS
The status of the digital outputs on the drive is displayed. It can also be read via a serial line or eldbus. The
data are contained in a word, where each bit is 1 if voltage is supplied to the corresponding input terminal.
1Output enabled.
0Output disabled.
I.e. :
00000000001
1
Attiva DO 1Attiva DO 2
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
1.23 1200 Digital input X mon UINT16 16 0 0 0 R VS
The status of the digital inputs of the expansion card is displayed. It can also be read via a serial line or
eldbus. The data are contained in a word, where each bit is 1 if voltage is supplied to the corresponding input
terminal. This parameter displays the state of the 16 external inputs. The 14 less signicant bits are displayed
from the keypad.
1Input enabled.
0Input disabled.
I.e. :
00000000001
1
Attivo DI 1Attivo DI 2
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
1.24 1400 Digital output X mon UINT16 0 0 0 R VS
The status of the digital outputs of the expansion card is displayed. It can also be read via a serial line or
eldbus. The data are contained in a word, where each bit is 1 if voltage is supplied to the corresponding input
terminal.
1Output enabled.
0Output disabled.
I.e. :
00000000001
1
Attiva DO
1Attiva
DO 2

ADV200 WA • Functions description and parameters list 11
2 – DRIVE INFO
This menu displays the information for identifying and conguring the drive.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
2.1 482 Drive size UINT16 00 0 R
The drive size identication code is displayed.
Size code Size text Family code Family text
1 0.75/1.5 kW 1 380V..480V
2 1.5/2.2 kW 1 380V..480V
3 2.2/3.0 kW 1 380V..480V
4 3.0/4.0 kW 1 380V..480V
5 4.0/5.5 kW 1 380V..480V
6 5.5/7.5 kW 1 380V..480V
7 7.5/11.0 kW 1 380V..480V
8 11.0/15.0 kW 1 380V..480V
9 15.0/18.5 kW 1 380V..480V
10 18.5/22.0 kW 1 380V..480V
11 22.0/30.0 kW 1 380V..480V
12 30.0/37.0 kW 1 380V..480V
13 37.0/45.0 kW 1 380V..480V
14 45.0/55.0 kW 1 380V..480V
15 55.0/75.0 kW 1 380V..480V
16 75.0/90.0 kW 1 380V..480V
17 90.0/110.0 kW 1 380V..480V
18 110.0/132.0 kW 1 380V..480V
19 132.0/160.0 kW 1 380V..480V
19 132.0/160.0 kW 1 380V..480V
20 160.0/200.0 kW 1 380V..480V
21 200.0/250.0 kW 1 380V..480V
22 250.0/315.0 kW 1 380V..480V
23 315.0/355.0 kW 1 380V..480V
24 355.0/400.0 kW 1 380V..480V
25 400.0/500.0 kW 1 380V..480V
26 500.0/630.0 kW 1 380V..480V
27 630.0/710.0 kW 1 380V..480V
28 710.0/800.0 kW 1 380V..480V
29 0.9/1.0 MW 1 380V..480V
30 1.0/1.2 MW 1 380V..480V
1 75.0/90.0 kW 3 690V
2 90.0/110.0 kW 3 690V
3 110.0/132.0 kW 3 690V
4 132.0/160.0 kW 3 690V
5 160.0 kW 3 690V
6 200.0 kW 3 690V
7 250.0 kW 3 690V
8 315.0 kW 3 690V
9 355.0 kW 3 690V
10 400.0 kW 3 690V
11 500.0 kW 3 690V
12 630.0 kW 3 690V
13 710.0 kW 3 690V
14 800.0 kW 3 690V
15 1000.0 kW 3 690V
16 1200.0 kW 3 690V
17 160.0/200.0 kW 3 690V
18 200.0/250.0 kW 3 690V
19 250.0/315.0 kW 3 690V

12 ADV200 WA • Functions description and parameters list
20 315.0/355.0 kW 3 690V
21 355.0/400.0 kW 3 690V
22 400.0/500.0 kW 3 690V
23 500.0/630.0 kW 3 690V
24 630.0/710.0 kW 3 690V
25 710.0/800.0 kW 3 690V
26 0.9/1.0 MW 3 690V
27 1.0/1.2 MW 3 690V
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
2.2 484 Drive family ENUM No Power 0 0 RS VS
The available mains voltage is displayed (e.g. 400V). The undervoltage alarm refers to this voltage value.
The condition No power occurs when the regulation board has just left from production and has never been
congured for any power. The conguration adjustment for a given power is achieved by linking it to a power
board and running a Save parameters.
0No Power
1380V…480V
2500V…575V
3690V
4230V
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
2.3 486 Drive region ENUM EU 0 1 R VS
The geographical area (Europe or USA) is displayed. The factory settings for the power supply voltage and
frequency used by the drive are dened accordingly.
0 EU (400V / 50Hz)
1 USA (460 / 60 Hz)
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
2.4 488 Drive cont current A FLOAT CALCF 0.0 0.0 RZS VS
The current that the drive can deliver continuously according to size, supply voltage and programmed switch-
ing frequency is displayed.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
2.5 490 Firmware ver.rel UINT16 0 0 0 R VS
The version number and release number of the drive rmware are displayed. On the keypad these are dis-
played in the version.release format. The parameter reading from the serial communication device or eldbus
returns the version in the high byte and the release in the low byte.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
2.6 496 Firmware type UINT16 0 0 0 R VS
The type of rmware installed in the drive is displayed.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
2.7 504 Application ver.rel UINT16 0 0 0 ER VS
The version and release number of the application used in the drive are displayed. On the keypad these
are displayed in version.release format. When the parameter is read via serial line or eldbus the version is
returned in the high byte and the release in the low byte.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
2.8 506 Application type UINT16 0 0 0 ER VS
The type of application currently used by the drive is displayed.

ADV200 WA • Functions description and parameters list 13
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
2.9 508 Application subver UINT16 0 0 0 ER VS
The Revision Index of the application currently used by the drive is displayed.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
2.10 518 Actual date time UINT32 0 0 0 R VS
The current date and time are displayed in dd/mm/yyy hh/min format.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
2.11 510 Time drive power on h.min UINT32 0 0 0 ER VS
The total time for which the drive has been powered is displayed.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
2.12 512 Time drive enable h.min UINT32 0 0 0 ER VS
The time for which the enable hardware contact on the drive has been connected is displayed.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
2.13 514 Number power up UINT16 0 0 0 ER VS
The number of times the drive has been powered on is displayed.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
2.14 516 Time fan on h.min UINT32 0 0 0 ER VS
The total operating time of the drive fan is displayed.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
2.15 530 Power file ver.rel UINT16 0 0 0 R VS
The version number and release number of the drive power card are displayed.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
2.16 530 Slot 1 card type ENUM None 0 0 R VS
2.17 532 Slot 2 card type ENUM None 0 0 R VS
2.18 534 Slot 3 card type ENUM None 0 0 R VS
The type of expansion card installed in the relative slot of the drive is displayed.
0None
769 I/O 1
1793 I/O 2
2305 I/O 3
3329 I/O 4
7681 I/O 8 (EXP-IO-SENS-1000-ADV)
5633 I/O 6 (EXP-IO-SENS-100-ADV)
6401 I/O 7 (EXP-IO-D5R8-ADV)
4Can/Dnet
260 Probus
516 RTE
255 Unknown

14 ADV200 WA • Functions description and parameters list
3 – STARTUP WIZARD
The startup wizard menu suggests a procedure for commissioning the drive quickly with a reduced number of settings.
Advanced customization requires the use of the single parameters relating to the specic performance levels. See the
procedure described in the Startup wizard chapter in Quick Start ADV200-WA -QS manual.

ADV200 WA • Functions description and parameters list 15
4 – DRIVE CONFIG
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
4.1 550 Save parameters BIT 0 0 1 RW VS
Any changes to parameter values immediately affect drive operations, but are not automatically saved in the
permanent memory.
The “Save Parameters” command is used to save current parameter values in the permanent memory.
Any changes that are not saved will be lost when the drive is switched off.
To save parameters follow the procedure described in STEP 6 of the Startup wizard.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
4.2 552 Regulation mode ENUM V/f control 0 2 RWZ VS
The ADV200 is capable of operating with different control modes:
0V/f control
1Flux vector OL
2Autotune
The open loop V/f (V/f control) mode is the simplest type of asynchronous motor control, as the only param-
eters required are the rated voltage, current and frequency of the motor.
The open loop V/F control mode is factory-set and does not require any speed feedback. The natural varia-
tion in speed generated by machine load induction (slippage) can be compensated using Slip comp and Slip
comp lter.
In V/f mode a single drive can be used to control several asynchronous motors, even of different sizes, con-
nected in parallel, provided the sum of the currents of the single motors is less than the drive rated current.
If using several motors connected in parallel, be sure to provide adequate thermal protection for each single
motor.
With the sensorless vector control (Flux vector OL) mode, high speed and torque precision can be
achieved at low motor rpm. The drive has a powerful algorithm that uses a self-tuning procedure to obtain all
the electric measurements of the motor. This allows the speed and position of the motor shaft to be estimated,
enabling operation similar to that of a drive with feedback, both in terms of the response in torque to load vari-
ations, and of the regularity of rotation even at very low rmp.
If the Startup wizard procedure is not used, self-tuning of the motor parameters is possible in the self-tuning
mode (Autotune). To execute the command the hardware enabling contact between terminals 7 and S2 must
be opened. Then set the Regulation Mode parameter to Autotune. If not already in Local mode, press the
Local key (the LOC LED lights up) and close the hardware enabling contact (terminals 7 and S3). Self-tuning
can now be enabled (refer to parameters 2022 or 2224). At the end of the self-tuning procedure, open the
contact between terminals 7 and S3 again and restore the parameters that were changed.
This procedure must be used for both self-tuning with the engine standing still and with the motor turning.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
4.3 554 Access mode ENUM Easy 0 1 RW VS
With this parameter you can restrict access to advanced conguration.
0Easy
1Expert
The Easy mode gives access to a list of parameters that can be used for rapid drive commissioning. This type
of conguration is suitable for the majority of applications.
Setting the parameter to Expert gives access to all the parameters in the rmware. This mode allows an ex-
tremely high level of customization to be achieved in order to exploit the potential of the ADV200 to the full.

16 ADV200 WA • Functions description and parameters list
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
4.4 556 Control mode select ENUM Ramp 0 2 ERWZ _S
Selection of the drive control mode.
0Torque
1Speed
2Ramp
In torque control (0 - Torque) the reference and load of the motor determine its speed and direction of rota-
tion. Symmetrical torque limits can be set, for each direction of rotation and for motor/generator operation.
In speed control (1 - Speed) the reference arrives straight after the ramp circuit, enabling an extremely rapid
response to signal variations. This is ideal for applications that require a highly dynamic response. This type of
control is available in the Flux vector OL control mode. In this mode the Ramp function is not used to gener-
ate the drive speed reference so it can be used in stand-alone mode.
In control with ramp (2 - Ramp) the speed reference is applied to the input of the “Ramp” block and is pro-
duced by the “Ramp ref” block. This allows setting of both the acceleration/deceleration times and the ramp
time (linear or S-shaped with customizable jerks). This type of control is available in all control.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
4.5 558 Application select ENUM None 0 2 ERWZ VS
Selection of which IEC 61131-3-compliant application.
0None
1Application 1 (Macro, see menu 27)
2Application 2 (Multidrive, see menu 27)
The drive is supplied already incorporating a number of applications developed in the IEC 61331-3 environ-
ment. To use these, set the desired application, run Save parameters, switch the drive off and then on again.
NOTE! The Load Default command (par. 580) does not modify this parameter
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
4.6 560 Mains voltage ENUM 400 V SIZE SIZE ERWZS VS
Setting of the available mains voltage value in Volts. Detection of the undervoltage alarm refers to this value.
0None
1 230 V
2 380 V
3400 V
4415 V
5440 V
6460 V
7480 V
8500 V
9575 V
10 690 V
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
4.7 586 DC supply ENUM None 0 7ERWZSVS
Selection of the voltage applied to the DC link if the drive is powered by an AC/DC power supply unit, whether
normal or regenerative (e.g. AFE200). If a value of other than “None” is selected, parameters that depend on
parameter 560 Mains voltage are calculated on the basis of the voltage shown in the table below, while the
value of parameter 560 Tensione di rete is set automatically.
If “None” is selected, these parameters are calculated according to the value of parameter 560 Mains voltage.

ADV200 WA • Functions description and parameters list 17
DC power supply Drive family 380V..480V
Mains voltage
Drive family 690V
Mains voltage
0 None Use P560 Use P560
1 540 V (380-480V) 400 V N/A
2 650 V (380-480V) 460 V N/A
3 750 V (380-480V) 460 V N/A
10 675 V (690V) N/A 500 V (
if compatible with the size, otherwise N/A )
11 810 V (690V) N/A 575 V (
if compatible with the size, otherwise N/A )
12 935 V (690V) N/A 690 V
13 1120 V (690V) N/A 690 V
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
4.8 450 Undervoltage V FLOAT CALCF CALCF CALCF ERWZSVS
Setting of the drive minimum operating voltage. The maximum and minimum default values are calculated
automatically by the drive according to the value set in parameter 560 Mains voltage, as shown in the table
below.
Table of undervoltage limits
Mains voltage Def Min Max
0 None (Vdc) (Vdc) (Vdc)
1 230 V 225 200 282
2 380 V 372 330 466
3 400 V 392 330 490
4 415 V 407 360 509
5 440 V 431 382 539
6 460 V 451 400 564
7 480 V 470 417 588
8 500 V 490 434 613
9 575 V 563 500 705
10 690 V 676 600 846
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
4.9 562 Switching frequency ENUM SIZE SIZE SIZE ERWS VS
Setting of the switching frequency value in kHz. The maximum value that can be set depends on the size of the drive.
See ADV200 WA Quick Start manual.
0 1 kHz
1 2 kHz
2 4 kHz
3 6 kHz
4 8 kHz
5 10 kHz
6 12 kHz
7 16 kHz
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
4.10 564 Ambient temperature ENUM 40 degC 0 1 ERWZ VS
Setting of the ambient temperature value. This parameter is used to set the output current derating factor (1%
for every °C above 40°C).
0 40 degC The inverter is capable of delivering direct current continuously with ambient temperatures of up
to 40°C.
1 50 degC The inverter is capable of delivering direct current continuously with ambient temperatures of up
to 50°C.
If the value is set to 1 the drive output current will be 10% less than the rated current at 40°C.

18 ADV200 WA • Functions description and parameters list
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
4.11 566 Drive overload mode ENUM Light duty 1 2 ERWZ VS
Setting of the overload that can be supplied by the drive, depending on the application.
1Heavy duty
2 Light duty
Set Heavy duty when a large overload is requested: the drive can supply 180% of the rated current for 0.5
seconds and 150% for 1 minute every 5 minutes.
Select Light duty to enable the drive to deliver a current of 110% of the rated current for 1 minute every 5
minutes.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
4.12 568 Switching freq mode ENUM Costant 0 1 ERWZS VS
Setting of the switching frequency operating mode when drive overload is set in Heavy duty. The factory
switching frequency setting is 4 kHz for motors between 2.2 kW and 37 kW (the factory switching frequency
setting for smaller drives is 8kHz); this value may result in increased noise. Setting a higher switching fre-
quency will increase drive losses and thus increase the heatsink temperature, but it will also reduce noise. To
combine the advantages of both settings, with the ADV drive the heatsink temperature can be controlled by
reducing the switching frequency if it increases.
0Costant
1Variable
If set to Costant the switching frequency is xed and is set using the Switching frequency parameter, ac-
cording to the size of the drive. If the selected switching frequency value is higher than the default value, the
output current of the drive is derated.
If set to Variable the switching frequency is set to 8kHz and controlled by the temperature of the drive heat-
sink and by the output frequency. If the heatsink temperature exceeds a set threshold (which depends on the
size of the drive) or falls to below 5Hz ± 1Hz, the switching frequency is automatically reduced to 4kHz, to
prevent derating of the output current. The switching frequency is reduced in a single step. With this setting
the switching frequency value selected in the Switching frequency parameter is ineffective.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
4.13 570 Password UINT32 0 0 99999 ERW VS
You can enter a password to protect the parameters from unauthorized tampering: the password can consist
of a combination of a maximum of any 5 gures that can be selected by the user. All parameters are locked,
except this one and Save parameters.
After entering the password, press the E key once to enter it into the memory and again to enable it (= Ena-
bled is displayed to indicate that the password is enabled).
So that the password remains valid even after switching the unit off and then switching it back on, save it us-
ing the Save parameters command.
When the password is enabled any attempts to modify a parameter are blocked and the Password enabled
message is displayed.
To disable the password, enter the Password parameter (572) in the DRIVE CONFIG menu.
Check that the password is enabled (Enabled), press E and enter the combination of gures that make up
the password.
Press E again. A message is displayed telling you the password is no longer enabled (Disabled).
To make sure the password continues to be disabled even after switching the unit off and then switching it
back on, save this conguration using the Save parameters command.
When an incorrect password is entered, the Password wrong message is displayed.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
4.14 572 Application key UINT32 0 0 4294967295 ERW VS
This parameter can be used to enter the key for enabling the PLC application.
You may need to enter a key to denitively enable some PLC applications. Please contact Gefran for details

ADV200 WA • Functions description and parameters list 19
about which PLC applications require the key.
If executing an application that envisages a key verication and the key is incorrect, enabling is forced for 200
hours (time drive enabled).
In this phase a message is displayed informing you that the period of forced enabling time is about to expire.
At the rst power-on after the 200 hours an alarm is generated and the application does not start.
Please contact Gefran for the numerical value of the key.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
4.15 574 Startup display INT16 -1 -1 20000 ERW VS
This is used to set the parameter that will be displayed automatically at drive power-on. Entering the value -1
(default), the function is disabled and the main menu is displayed at power-on.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
4.16 576 Display backlight BIT 0 0 1 ERW VS
Enabling of the backlight on the drive display.
If set to 0the display backlight will go off when the drive has been on for three minutes.
If set to 1the backlight will stay on for as long as the drive is powered.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
4.17 578 Language select ENUM English 0 9 RWZ VS
Setting of the drive programming language.
0 English
1Italian
2 French
3 German
4 Spanish
5 Polish
6 Romanian
7 Russian
8 Turkish
9 Portuguese
Note ! The Load Default command (par. 580) does not modify this parameter.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
4.18 580 Load default BIT 0 0 1 RWZ VS
Transfers the standard factory settings to the drive memory (“Def” column in the parameters table).
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
4.19 590 Save par to keypad BIT 0 0 1 RW VS
Transfers the parameters currently stored in the drive and saves them in the keypad memory (See ADV200
WA Quick Start manual, chapter 6.8).
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
4.20 592 Load par from keypad BIT 0 0 1 RWZ VS
Transfers the parameters from the keypad memory to the drive (See ADV200 Quick Start manual, chapter
6.9).
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
4.21 594 Keypad memory select UINT16 1 1 5 ERW VS
Selection of the area of the keypad memory to which to transfer and save the parameters stored in the drive.

20 ADV200 WA • Functions description and parameters list
5 – REFERENCES
ADV drives are provided with a speed regulation circuit, which can be adapted to suit the various applications. In the
standard version, the regulator has PI behaviour and the regulator parameters are the same for the entire eld of regu-
lation.
Different sources can be used for the speed and torque references, depending on how the 554 Control mode select
parameter is set.
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
5.1 600 Dig ramp ref 1 FF INT16 16/32 0 CALCI CALCI RW VS
Setting of the digital ramp reference. The speed that the drive must reach after completing the acceleration
phase is set with the ramp reference. Variations in the ramp reference are made with the selected ramp times.
The size of the ramp reference determines the motor speed value. The sign determines the direction of rota-
tion. The Ramp ref parameter also refers to a minimum speed, if set. When the “Motor potentiometer” or
“Multispeed” functions are selected the relative references are used. This reference can only be used in the
Remote mode.
The overall ramp reference is the result of the sum of the values with the Ramp ref 1 and Ramp ref 2 sign.
Example 1: Ramp ref 1 = + 500 rpm Ramp ref 2 = + 300 rpm
Ramp ref = 500 rpm + 300 rpm = 800 rpm
Example 2: Ramp ref 1 = + 400 rpm Ramp ref 2 = - 600 rpm
Ramp ref = 400 rpm – 600 rpm = - 200 rpm
Menu PAR Description UM Type FB BIT Def Min Max Acc Mod
5.2 602 Dig ramp ref 2 FF INT16 16/32 0 CALCI CALCI ERW VS
Setting of the digital ramp reference. The speed that the drive must reach after completing the acceleration
phase is set with the ramp reference. Variations in the ramp reference are made with the selected ramp times.
The size of the ramp reference determines the motor speed value. The sign determines the direction of rota-
tion. The Ramp ref parameter also refers to a minimum speed, if set. When the “Motor potentiometer” or
“Multispeed” functions are selected the relative references are used.
In Remote mode the overall ramp reference is the result of the sum of the values with the Ramp ref 1 and
Ramp ref 2 sign.