gefran AGy-EV Series User manual

.....Instruction Manual
SIEIDrive
General-Purpose Inverter
230/400/460V Class
575V Class
AGy -EV

Thank you for choosing this Gefran product.
We will be glad to receive any possible information which could help us improving this manual. The e-mail address is the following:
[email protected] .
Before using the product, read the safety instruction section carefully.
Keep the manual in a safe place and available to engineering and installation personnel during the product functioning period.
Gefran S.p.A has the right to modify products, data and dimensions without notice.
The data can only be used for the product description and they can not be understood as legally stated properties.
This manual is updated according to firmware version V03.04.
All rights reserved

AGy-EV Instruction Manual Table of Contents • 3
Table of Contents
Safety Symbol Legend - Precautions de securité...................................................................... 6
Chapter 1 - Safety Precautions ..................................................................................................7
1.1 Power Supply and Grounding ..................................................................................................................................................... 10
Chapter 2 - General................................................................................................................... 11
Features............................................................................................................................................................................................12
Accessories / Options .......................................................................................................................................................................12
Chapter 3 - Inspection Procedure, Component Identification and Standard Specification.... 13
3.1 Upon Delivery Inspection Procedures........................................................................................................................................ 13
3.1.1 General ....................................................................................................................................................................................13
3.1.2 Inverter Type Designation ........................................................................................................................................................13
3.1.3 Nameplate ...............................................................................................................................................................................14
3.2 Component Identification ........................................................................................................................................................... 15
3.3 Standard Specifications ............................................................................................................................................................. 16
3.3.1 Permissible Environmental Conditions......................................................................................................................................16
Disposal of the Device ...............................................................................................................................................................17
3.3.2 Mains Connection and Inverter Output.....................................................................................................................................17
3.3.3 AC Input Current ......................................................................................................................................................................20
3.3.4 AC Output ................................................................................................................................................................................20
3.3.5 Open-Loop and Closed-Loop Control Section ...........................................................................................................................21
3.3.6Accuracy..................................................................................................................................................................................21
Chapter 4 - Installation Guidelines........................................................................................... 23
4.1 Mechanical Specification........................................................................................................................................................... 23
4.2 Watts Loss, Heat Dissipation, Internal Fans and Minimum Cabinet Opening Suggested for the Cooling................................ 27
4.2.1 Cooling Fans Power Supply .....................................................................................................................................................28
4.3 Installation Mounting Clearance ................................................................................................................................................ 29
4.4 Motors and Encoder ................................................................................................................................................................... 30
4.4.1 AC Induction Motors ................................................................................................................................................................30
4.4.2 Encoder....................................................................................................................................................................................31
Chapter 5 - Wiring Procedure .................................................................................................. 33
5.1 Accessing to the Connectors ..................................................................................................................................................... 33
5.2 Power Section ............................................................................................................................................................................ 35
5.2.1 Maximum Cable Cross Section for Power Terminals ................................................................................................................36
5.2.2 Rectification and Intermediate (D.C.) Circuit............................................................................................................................37
5.2.3 Inverter ....................................................................................................................................................................................38
5.3 Regulation Section...................................................................................................................................................................... 39
5.3.1 R-AGy Regulation Card.............................................................................................................................................................39
5.3.2 Terminal Assignments on Regulation Section ...........................................................................................................................40
5.4 Serial Interface ........................................................................................................................................................................... 41
5.4.1 In General ................................................................................................................................................................................41
5.4.2 RS 485 Serial Interface Connector Description ........................................................................................................................42
5.5 Typical Connection Diagrams..................................................................................................................................................... 43
5.5.1 AGy Connection .......................................................................................................................................................................43
5.5.2 Engineering Notes ...................................................................................................................................................................44
5.5.3. Parallel Connection on the AC (Input) and DC (Intermediate Circuit) Side of Several Inverters ...............................................45
5.6 Circuit Protection........................................................................................................................................................................ 46
5.6.1 External Fuses of the Power Section........................................................................................................................................46
5.6.2 External Fuses of the Power Section DC Input Side ................................................................................................................47
5.6.3 Internal Fuses ..........................................................................................................................................................................48
5.7 Chokes / Filters (Optional) .......................................................................................................................................................... 48
5.7.1 AC Input Chokes ......................................................................................................................................................................49
5.7.2 Output Chokes .........................................................................................................................................................................49

4 • Table of Contents AGy-EV Instruction Manual
5.7.3 Interference Suppression Filters ..............................................................................................................................................50
5.7.3.1 EMI filter connections for Sizes 1007...3150 (230V...480V)...........................................................................................52
5.7.3.2 EMI filter connections for Sizes 4185...82000 (230V...480V).........................................................................................53
5.8 Braking in the AGy System ........................................................................................................................................................ 54
5.8.1 Braking Unit .............................................................................................................................................................................54
5.8.1.1 External Braking Resistor...............................................................................................................................................56
5.8.2 D.C. Braking .............................................................................................................................................................................59
5.9 Discharge Time of the DC-Link................................................................................................................................................... 59
Chapter 6 - Drive Keypad Operation......................................................................................... 60
6.1 Keypad ........................................................................................................................................................................................ 60
6.2 Language Selection .................................................................................................................................................................... 61
6.3 Updating the language in E@syDrives ...................................................................................................................................... 61
6.4 Moving Through the Drive Main Menu ...................................................................................................................................... 62
6.5 Scrolling Through the Drive Parameters.................................................................................................................................... 63
6.6 Parameters Modification............................................................................................................................................................ 63
6.7 Quickstart procedure.................................................................................................................................................................. 64
Basic settings for trial run .................................................................................................................................................................64
Standard settings..............................................................................................................................................................................64
Advanced settings ............................................................................................................................................................................66
Chapter 7 - Parameter Description .......................................................................................... 67
7.1 Parameters List........................................................................................................................................................................... 67
7.2 Menu d - DISPLAY ..................................................................................................................................................................... 96
Basic.................................................................................................................................................................................................96
Overload ...........................................................................................................................................................................................97
Inputs/Outputs ..................................................................................................................................................................................98
Encoder...........................................................................................................................................................................................101
Option .............................................................................................................................................................................................102
Pid ..................................................................................................................................................................................................102
Alarmlist.........................................................................................................................................................................................103
DriveIdentification ..........................................................................................................................................................................103
Utility ..............................................................................................................................................................................................104
7.3 Menu S - START-UP................................................................................................................................................................. 105
Power Supply .................................................................................................................................................................................105
V/F Characteristic...........................................................................................................................................................................105
Motor Data .....................................................................................................................................................................................106
Commands & Referencies ...............................................................................................................................................................107
Functions ........................................................................................................................................................................................109
Utility ..............................................................................................................................................................................................110
7.4 Menu I - INTERFACE................................................................................................................................................................ 111
Digital Inputs Regulation Board .......................................................................................................................................................111
Digital Inputs Expansion Board........................................................................................................................................................112
Programmable Logic Output............................................................................................................................................................113
Digital Ouputs Regulation Board......................................................................................................................................................113
Digital Outputs Expansion Board .....................................................................................................................................................115
Analog Inputs Regulation Board ......................................................................................................................................................116
Analog Outputs Regulation Board....................................................................................................................................................120
Analog Outputs Exp Board ..............................................................................................................................................................123
Enabling Virtual I/O .........................................................................................................................................................................124
Encoder Configuration.....................................................................................................................................................................129
Serial Configuration.........................................................................................................................................................................130
Options Configuration......................................................................................................................................................................132
SBI Configuration ............................................................................................................................................................................133
7.5 Menu F - FREQ & RAMPS ........................................................................................................................................................ 135
Motorpotentiometer........................................................................................................................................................................135
Reference Limits .............................................................................................................................................................................137
Reference Sources..........................................................................................................................................................................138
Multispeed Function .......................................................................................................................................................................139

AGy-EV Instruction Manual Table of Contents • 5
Ramp Configuration.........................................................................................................................................................................141
Jump Frequencies...........................................................................................................................................................................143
7.6 Menu P - PARAMETERS .......................................................................................................................................................... 145
Commands......................................................................................................................................................................................145
Control Mode..................................................................................................................................................................................150
Power Supply .................................................................................................................................................................................151
Motor Data .....................................................................................................................................................................................151
V/F Curve ........................................................................................................................................................................................152
Ouput Frequency Limit ....................................................................................................................................................................154
Slip Compensation ..........................................................................................................................................................................154
Boost ..............................................................................................................................................................................................155
Automatic Flux Regulation...............................................................................................................................................................156
AntiOscillation Function..................................................................................................................................................................156
Closed Loop Speed Control.............................................................................................................................................................156
SW Current Clamp ..........................................................................................................................................................................158
Current Limit ...................................................................................................................................................................................159
DC Link Limit ...................................................................................................................................................................................161
Over Torque Alarm Configuration ....................................................................................................................................................162
Motor Overload Configuration .........................................................................................................................................................163
BU Configuration .............................................................................................................................................................................163
DC Brake Configuration...................................................................................................................................................................164
Autocapturefunction.......................................................................................................................................................................165
Undervoltage Configuration.............................................................................................................................................................167
Overvoltage Configuration...............................................................................................................................................................171
Autoreset Configuration ..................................................................................................................................................................172
External Fault Configuration ............................................................................................................................................................173
Phase Loss Detection .....................................................................................................................................................................173
Voltage Reduction Configuration .....................................................................................................................................................174
Frequency Threshold.......................................................................................................................................................................175
Steady State Signalling...................................................................................................................................................................177
Heatsink Temperature Threshold.....................................................................................................................................................177
PWM Setting ..................................................................................................................................................................................178
Dead Time Compensation ...............................................................................................................................................................179
Display Setting................................................................................................................................................................................179
Protection .......................................................................................................................................................................................180
7.7 Menu A - APPLICATION .......................................................................................................................................................... 181
PID Setting......................................................................................................................................................................................181
PID Gains ........................................................................................................................................................................................185
PID Limits........................................................................................................................................................................................185
Programmable Logic Inputs............................................................................................................................................................188
7.8 Menu C - COMMANDS ............................................................................................................................................................ 190
Basic...............................................................................................................................................................................................190
Alarm Register Reset ......................................................................................................................................................................190
External Key....................................................................................................................................................................................191
LCD keypad.....................................................................................................................................................................................191
Tuning .............................................................................................................................................................................................191
7.9 Menu H - HIDDEN .................................................................................................................................................................... 192
Virtual I/O Commands .....................................................................................................................................................................192
Profidrive Parameters .....................................................................................................................................................................193
Drive Status ....................................................................................................................................................................................194
Parameters Reading Extension........................................................................................................................................................194
Remote I/Os Control........................................................................................................................................................................195
Serial Link Commands.....................................................................................................................................................................195
7.10 Other functions ...................................................................................................................................................................... 196
7.10.1 Hour of life of the drive ........................................................................................................................................................196
Chapter 8 - Serial Protocol..................................................................................................... 197
8.1 Modbus RTU Protocol for AGy drives ...................................................................................................................................... 197
8.1.1 Introduction............................................................................................................................................................................197
8.1.2 The MODBUS Protocol ..........................................................................................................................................................197
8.1.3 Message format.....................................................................................................................................................................197

6 • Table of Contents AGy-EV Instruction Manual
Safety Symbol Legend - Precautions de securité
Indicates a procedure, condition, or statement that, if not strictly observed, could result in per-
sonal injury or death.
Indique le mode d'utilisation, la procédure et la condition d'exploitation. Si ces consignes ne sont pas
strictement respectées, il y a des risques de blessures corporelles ou de mort.
Indicatesaprocedure,condition,orstatementthat,ifnotstrictly observed, could result in damage
to or destruction of equipment.
Indique et le mode d'utilisation, la procédure et la condition d'exploitation. Si ces consignes ne sont pas
strictement respectées, il y a des risques de détérioration ou de destruction des appareils
Indicates a procedure, condition, or statement that should be strictly followed in order to optimize
these applications.
Indique le mode d'utilisation, la procédure et la condition d'exploitation. Ces consignes doivent être
rigoureusement respectées pour optimiser ces applications.
NOTE!Indicates an essential or important procedure, condition, or statement.
Indique un mode d'utilisation, de procédure et de condition d'exploitation essentiels
ou importants
Warning!
Caution
Attention
8.1.3.1 The address ..................................................................................................................................................................197
8.1.3.2 The function code .........................................................................................................................................................197
8.1.3.3 CRC16...........................................................................................................................................................................198
8.1.3.4 Message synchronization .............................................................................................................................................198
8.1.3.5 Serial line setting ..........................................................................................................................................................198
8.1.4 Modbus functions for the drive ..............................................................................................................................................199
8.1.4.1 Read Output Registers (03)...........................................................................................................................................199
8.1.4.2 Read Input Registers (04) .............................................................................................................................................199
8.1.4.3 Preset Single Register (06) ...........................................................................................................................................200
8.1.4.4 Read Status (07)...........................................................................................................................................................200
8.1.4.5 Preset Multiple Registers (16) ......................................................................................................................................201
8.1.5 Error management .................................................................................................................................................................201
8.1.5.1 Exception codes ...........................................................................................................................................................202
8.1.6 System configuration .............................................................................................................................................................202
8.2 Proprietary protocol.................................................................................................................................................................. 203
8.2.1 Introduction............................................................................................................................................................................203
8.2.2 Message format.....................................................................................................................................................................203
8.2.3 Address .................................................................................................................................................................................204
8.2.4 Control code ..........................................................................................................................................................................204
8.2.5 Functions ...............................................................................................................................................................................204
8.2.6 Msg Slave meaning ...............................................................................................................................................................205
Chapter 9 - Troubleshooting ................................................................................................... 207
9.1 Drive Alarm Condition .............................................................................................................................................................. 207
9.2 Alarm Reset .............................................................................................................................................................................. 207
9.3 List of Drive Alarm Events........................................................................................................................................................ 208
9.4 Kbg fw mismatch...................................................................................................................................................................... 208
Chapter 10 - EMC Directive.................................................................................................... 209
Index Parameters ................................................................................................................... 210

AGy-EV Instruction manual Chapter 1 - Safety • 7
Chapter 1 - Safety Precautions
According to the EEC standards the AGy-EV and accessories must be used only after checking
that the machine has been produced using those safety devices required by the 89/392/EEC set
ofrules,as far as themachineindustry is concerned. Thesestandardsdonotapply in theAmericas,
but may need to be considered in equipment being shipped to Europe.
Drive systems cause mechanical motion. It is the responsibility of the user to insure that any
such motion does not result in an unsafe condition. Factory provided interlocks and operating
limits should not be bypassed or modified.
Selon les normes EEC, les drives AGy-EV et leurs accessoires doivent être employés seulement après
avoir verifié que la machine ait été produit avec les même dispositifs de sécurité demandés par la
réglementation 89/392/EEC concernant le secteur de l’industrie.
Les systèmes provoquent des mouvements mécaniques. L’utilisateur est responsable de la sécurité
concernantles mouvementsmécaniques. Les dispositifs desécurité prévues par l’usine et leslimitations
operationelles ne doivent être dépassés ou modifiés.
Electrical Shock and Burn Hazard:
When using instruments such as oscilloscopes to work on live equipment, the oscilloscope’s
chassis should be grounded and a differential amplifier input should be used. Care should be
used in the selection of probes and leads and in the adjustment of the oscilloscope so that
accurate readings may be made. See instrument manufacturer’s instruction book for proper
operation and adjustments to the instrument.
Décharge Èlectrique et Risque de Brúlure :
Lors de l’utilisation d’instruments (par example oscilloscope) sur des systémes en marche, le chassis de
l’oscilloscope doit être relié à la terre et un amplificateur différentiel devrait être utilisé en entrée.
Lessondes et conducteursdoiventêtre choissis avecsoin pour effectuer lesmeilleures mesures à l’aide
d’un oscilloscope. Voir le manuel d’instruction pour une utilisation correcte des instruments.
Fire and Explosion Hazard:
Fires or explosions might result from mounting Drives in hazardous areas such as locations where
flammable or combustible vapors or dusts are present. Drives should be installed away from
hazardous areas, even if used with motors suitable for use in these locations.
Risque d’incendies et d’explosions:
L’utilisation des drives dans des zônes à risques (présence de vapeurs ou de poussières inflammables),
peut provoquer des incendies ou des explosions. Les drives doivent être installés loin des zônes
dangeureuses, et équipés de moteurs appropriés.
Strain Hazard:
Improper lifting practices can cause serious or fatal injury. Lift only with adequate equipment and
trained personnel.
Attention à l’Élévation:
Une élévation inappropriée peut causer des dommages sérieux ou fatals. Il doit être élevé seulement
avec des moyens appropriés et par du personnel qualifié.
Drives and motors must be ground connected according to the NEC.
Touslesmoteurs et lesdrivesdoivent être misà laterreselon le CodeElectrique Nationalou équivalent.
Replace all covers before applying power to the Drive. Failure to do so may result in death or
serious injury.
Remettre tous les capots avant de mettre sous tension le drive. Des erreurs peuvent provoquer de
sérieux accidents ou même la mort.
Adjustable frequency drives are electrical apparatus for use in industrial installations. Parts of the
Drivesare energizedduring operation.The electricalinstallationandthe openingof thedevice should
therefore only be carried out by qualified personnel. Improper installation of motors or Drives may
therefore cause the failure of the device as well as serious injury to persons or material damage.
Driveisnotequippedwithmotoroverspeedprotectionlogicotherthanthatcontrolledbysoftware.Follow
the instructions given in this manual and observe the local and national safety regulations applicable.
Les drives à fréquence variable sont des dispositifs électriques utilisés dans des installations industriels.
Une partie des drives sont sous tension pendant l’operation. L’installation électrique et l’ouverture des
drives devrait être executé uniquement par du personel qualifié. De mauvaises installations de moteurs
Warning!

8 • Chapter 1 - Safety AGy-EV Instruction manual
ou de drives peuvent provoquer des dommages materiels ou blesser des personnes.On doit suivir les
instructions donneés dans ce manuel et observer les régles nationales de sécurité.
Always connect the Drive to the protective ground (PE) via the marked connection terminals
(PE2) and the housing (PE1). AGy Drives and AC Input filters have ground discharge currents
greater than 3.5 mA. EN 50178 specifies that with discharge currents greater than 3.5 mA the
protective conductor ground connection (PE1) must be fixed type and doubled for redundancy.
Il faut toujours connecter le variateur à la terre (PE) par les des bornes (PE2) et le châssis (PE1). Le
courant de dispersion vers la terre est supérieur à 3,5 mA sur les variateurs Brushless et sur les filtres à
courant alterné (CA). Les normes EN 50178 spécifient qu'en cas de courant de dispersion vers la terre,
supérieur à 3,5 ma, la mise à la terre (PE1) doit avoir une double connexion pour la redondance.
The drive may cause accidental motion in the event of a failure, even if it is disabled, unless it has
been disconnected from the AC input feeder.
En cas de panne, le variateur peut causer une mise en marche accidentelle, même s'il est désactivé,
sauf s'il a été débranché de l'alimentateur à courant alterné.
Never open the device or covers while the AC Input power supply is switched on. Minimum time
to wait before working on the terminals or inside the device is listed in section 5.9 on Instruction
manual .
Nejamaisouvrir l’appareillorsqu’ilestsunstension. Le tempsminimum d’attenteavantdepouvoirtravailler
sur les bornes ou bien à l’intérieur de l’appareil est indiqué dans la section 5.9.
If the front plate has to be removed because of ambient temperature higher than 40 degrees, the
user has to ensure that no occasional contact with live parts may occur.
Si la plaque frontale doit être enlevée pour un fonctionnement avec la température de l’environnement
plushauteque40°C,l’utilisateur doit s’assurer,pardesmoyensopportuns,qu’aucuncontactoccasionnel
ne puisse arriver avec les parties sous tension.
Do not connect power supply voltage that exceeds the standard specification voltage fluctuation
permissible. If excessive voltage is applied to the Drive, damage to the internal components will
result.
Ne pas raccorder de tension d’alimentation dépassant la fluctuation de tension permise par les normes.
Danslecas d’unealimentationentensionexcessive, descomposantsinternes peuvent êtreendommagés.
Do not operate the Drive without the ground wire connected. The motor chassis should be grounded to
earth through a ground lead separate from all other equipment ground leads to prevent noise coupling.
Nepasfairefonctionnerle drivesansprisede terre.Lechassisdu moteurdoit êtremisàlaterreàl’aided’un
connecteur de terre separé des autres pour éviter le couplage des perturbations. Le connecteur de terre
devrait être dimensionné selon la norme NEC ou le Canadian Electrical code.
The grounding connector shall be sized in accordance with the NEC or Canadian Electrical Code.
The connection shall be made by a UL listed or CSA certified closed-loop terminal connector
sized for the wire gauge involved. The connector is to be fixed using the crimp tool specified by
the connector manufacturer.
Le raccordement devrait être fait par un connecteur certifié et mentionné à boucle fermé par les
normes CSA et ULet dimensionné pour l’épaisseur du cable correspondant. Le connecteur doit être
fixé a l’aide d’un instrument de serrage specifié par le producteur du connecteur.
Do not perform a megger test between the Drive terminals or on the control circuit terminals.
Ne pas exécuter un test megger entre les bornes du drive ou entre les bornes du circuit de contrôle.
Because the ambient temperature greatly affects Drive life and reliability, do not install the
Drive in any location that exceeds the allowable temperature. Leave the ventilation cover
attached for temperatures of 104° F (40° C) or below.
Étant donné que la température ambiante influe sur la vie et la fiabilité du drive, on ne devrait pas
installer le drive dans des places ou la temperature permise est dépassée. Laisser le capot de
ventilation en place pour températures de 104°F (40°C) ou inférieures.
Warning!
Caution

AGy-EV Instruction manual Chapter 1 - Safety • 9
If the Drive’s FaultAlarm is activated, consult the TROUBLESHOOTING section of this instruction
book, and after correcting the problem, resume operation. Do not reset the alarm automatically
by external sequence, etc.
Si la Fault Alarm du drive est activée, consulter la section du manuel concernant les défauts et après avoir
corrigél’erreur,reprendrel’opération.Nepasréiniliatiserl’alarmeautomatiquementparuneséquenceexterne,
etc.
Be sure to remove the desicant dryer packet(s) when unpacking the Drive. (If not removed these
packets may become lodged in the fan or air passages and cause the Drive to overheat).
Lorsdu déballage dudrive,retirer le sachetdéshydraté.(Si celui-ci n’estpas retiré, ilempêchela ventilation
et provoque une surchauffe du drive).
The Drive must be mounted on a wall that is constructed of heat resistant material. While the
Drive is operating, the temperature of the Drive's cooling fins can rise to a temperature of 194° F
(90°C).
Le drive doit être monté sur un mur construit avec des matériaux résistants à la chaleur. Pendant le
fonctionnementdu drive, latempérature desailettes dudissipateur thermique peutarriver à194°F(90°).
Do not touch or damage any components when handling the device. The changing of the isolation
gaps or the removing of the isolation and covers is not permissible.
Manipulerl’appareildefaçonànepastoucher ou endommager des parties. Il n’est paspermisdechanger
les distances d’isolement ou bien d’enlever des matériaux isolants ou des capots.
Protectthe device from impermissibleenvironmentalconditions (temperature, humidity,shocketc.)
Protéger l’appareil contre des effets extérieurs non permis (température, humidité, chocs etc.).
No voltage should be connected to the output of the drive (terminals U2, V2 W2). The parallel connection
of several drives via the outputs and the direct connection of the inputs and outputs (bypass) are not
permissible.
Aucune tension ne doit être appliquée sur la sortie du convertisseur (bornes U2, V2 et W2). Il n’est pas
permisderaccorderlasortiedeplusieursconvertisseursenparallèle,nid’effectueruneconnexiondirecte
de l’entrée avec la sortie du convertisseur (Bypass).
A capacitative load (e.g. Var compensation capacitors) should not be connected to the output of
the drive (terminals U2, V2, W2).
Aucunechargecapacitivenedoitêtreconnectéeàlasortieduconvertisseur(bornesU2,V2etW2)(parexemple
des condensateurs de mise en phase).
The electrical commissioning should only be carried out by qualified personnel, who are also
responsible for the provision of a suitable ground connection and a protected power supply
feeder in accordance with the local and national regulations. The motor must be protected against
overloads.
La mise en service électrique doit être effectuée par un personnel qualifié. Ce dernier est responsable de
l’existence d’une connexion de terre adéquate et d’une protection des câbles d’alimentation selon les
prescriptions locales et nationales. Le moteur doit être protégé contre la surcharge
No dielectric tests should be carried out on parts of the drive. A suitable measuring instrument
(internal resistance of at least 10 kΩΩ
ΩΩ
Ω//
//
/V) should be used for measuring the signal voltages.
Il ne faut pas éxécuter de tests de rigidité diélectrique sur des parties du convertisseurs. Pour mesurer les
tensions, des signaux, il faut utiliser des instruments de mesure appropriés (résistance interne minimale 10
k Ω /V).
Caution
NOTE!Ifthe Driveshave beenstored forlonger than twoyears, theoperation of theDC linkcapacitorsmaybe impaired
and must be “reformed”.
Before commissioning devices that have been stored for long periods, connect them to a power supply for two
hours with no load connected in order to regenerate the capacitors, (the input voltage has to be applied without
enabling the drive).
Encasdestockagedesvariateurspendantplusdedeuxans,ilestconseillédecontrôlerl'étatdescondensateurs
CC avant d'en effectuer le branchement. Avant la mise en service des appareils, ayant été stockés pendant
longtemps,il faut alimenter variateursà vide pendant deuxheures, pour régénérer lescondensateurs : appliquer
une tension d'alimentation sans actionner le variateur .
NOTE!The terms “Inverter”, “Controller” and “Drive” are sometimes used interchangably throughout the industry. We
will use the term “Drive” in this document.
Les mots “Inverter”, “Controller” et “Drive” sont interchangeables dans le domaine industriel. Nous utiliserons
dans ce manuel seulement le mot “Drive”.

10 • Chapter 1 - Safety AGy-EV Instruction manual
1.1 Power Supply and Grounding
1) GEFRAN drives are designed to be powered from standard three phase lines that are electrically symmetrical
with respect to ground (TN or TT network).
Les variateurs GEFRAN sont prévus pour être alimentés par un réseau triphasé équilibré avec un régime de neutre
standard (TN ou TT).
2) In case of supply with IT network, the use of delta/wye transformer is mandatory, with a secondary three phase
wiring referred to ground.
Si le régime de neutre est IT, nous vous recommendons d'utiliser un tranformateur triangle/étoile avec point milieu
ramené à la terre.
In case of a three phase supply not symmetrical to ground, an insulation loss of one of the devices
connected to the same network can cause functional problem to the drive, if the use of a delta/wye
transformer is avoided.
Si le réseau n'est pas équilibré par rapport à la terre et qu'il n'y a pas de transformateur raingle/étoile,
une mauvaise isolation d'un appareil électrique connecté au même réseau que le variateur peut lui
causer des troubles de fonctionnement.
Please refer to the following connection sample.
Safety
ground
L1
L2
L3
Earth
U1/L1
V1/L2
W1/L3
U2/T1
V2/T2
W2/T3
PE2/
All wires (including motor ground) must
be connected inside the motor terminal box
AC OUTPUT
CHOKE
AC Main Supply
AC INPUT
CHOKE
PE1/
Warning!

AGy-EV Instruction manual Chapter 2 - General • 11
Chapter 2 - General
SieiDrive-AGy-EVis anACDigitalInvertersfor the variation ofthe speed of three-phasemotors.TheAGycan be supplied
with a power range from 0.75kW up to 200kW (230V...480V) and from 2Hp up to 200Hp (575V).
AnintermediatevoltageisgeneratedfromtherectifiedAC voltage.The Inverter bridge then produces, from this intermediate
voltage,power supply withvariable voltage and frequency,by means of sinusoidalevaluated pulse-widthmodulation.This
power supply provides motors with excellent running characteristics, even in a lower range.
The power supply voltage of the various cards is obtained through a switching from the intermediate circuit voltage.
The inverter power part is based on IGBT component (Insulated Gate Bipolar Transistor). The output is protected against
short-circuits and earth faults. It is possible to switch motors on and off during the Inverter operation (see chapter 5.2.3)
IfAC motors that are not specially manufactured to operate with an inverter are used, a reduction of 5...10% in supplied
current must be taken into account. In case that the rated torque is requested even in the low frequency range, further
reductions of the heat will be obtained by an external fan. If no assisted ventilation is available, oversizing of the power of
the motor will be necessary. In both cases we suggest to consult the motor manufacturer.
For mechanical reasons (bearings, unbalanced mass, etc.) the motor manufacturer should be consulted when the motor
is operated above the rated frequency.
AGy Inverters can be controlled in different ways:
- via terminal strip on the drive
- via an operator keypad
- via a standard PC program through RS 485 interface
SieiDrive - AGy-EV allows a smooth open-loop control and by using EXP-ENC-AGY option closed-loop control. With
closed-loop control, an encoder (a pulse generator) provides speed feedback information.
The power section and the control electronics are galvanically isolated.

12 • Chapter 2 - General AGy-EV Instruction manual
Features
- Supply voltages generated by switching starting from the intermediate circuit voltage.
- Reduction of motor noise is achieved by the use of a special PWM control procedure.
- The output of the Inverter is protected against short circuits and earth faults.
- Motors can be switched on and off at the Inverter output (see chapter 5.2.4 of the manual).
- The Inverter is protected against overcurrents, undervoltages and overvoltages.
- Voltage dips (up to 15 ms for the power section) can be bridged; for the control section (see chapter 7.6 for the
automatic restart programmation).
- Sinusoidal output current generated by means of sinusoidally evaluated pulse-width modulation
- Excellent motor running characteristics, even in the lower frequency range.
- Programmable slip compensation reduces load-initiated changes in speed to a minimum.
- Voltage can be boosted in the lower frequency range, either manually or automatically (boost).
- Automatic voltage and frequency adjustment under an overload ensures the Inverter cannot stall.
- Parameters can be set either via a keypad or via an RS 485 interface.
- Reference value in the form of an analog signal 0...10 V, -10...10V, 0...20 mA, 4...20 mAas a frequency or via a serial
interface.
- Ramp function generator with linear or S-shaped ramp.
- Direct current braking by commands:
a - thru digital input;
b - automatic injection below a set frequency;
c - Before starting the motor; used with pump and fan drives which are driven by the medium or by the air and are
already turning before the drive is started. D.C. braking prevents the Inverter being switched on when already
turning.
- Arange of voltage-frequency characteristics can be selected.
- Overload control.
- The last alarm 4 messages can be stored.Alarm messages are retained even after power failure.
- Open-loop or closed-loop operation, as desired.
- Indication via a potential-free contact and via the interface when a preselected speed is exceeded. Example of an
application: indication of stationary drive.
- Control via an RS 485 serial interface.
- Internal brake unit.
- Programmable logic
- Save parameters from the keyboard
- Recovery of parameters from the keyboard
- Change of language set up of the keyboard from E@syDrives
Accessories / Options
- Drive version (“-C”) with CANopen / DeviceNet integrated.
- External EMC input filters.
- External Input / Output chokes.
- External braking resistors (connected between terminals C and BR1).
- Encoder expansion card: EXP-ENC-AGY(code S525L)
- Remote keypad kit (code S5WW5).
-E
2PROM key: PRG-KEY (code S6F38).
- I/O expansion card: EXP-D6A1R1-AGy (code S524L).
- 120 Vac digital input interface card : EXP-D8-120 (code S520L).
- Profibus interface card: SBI-PDP-AGy (code S5H28).

AGy-EV Instruction manual Chapter 3 Inspection Procedure, Component Identification and Standard Specification • 13
Chapter 3 - Inspection Procedure, Component Identification
and Standard Specification
3.1 Upon Delivery Inspection Procedures
3.1.1 General
Ahigh degree of care is taken in packing theAGy Drives and preparing them for delivery. They should only be transported
with suitable transport equipment (see weight data). Observe the instructions printed on the packaging. This also applies
when the device is unpacked and installed in the control cabinet.
Upon delivery, check the following:
- the packaging for any external damage
- whether the delivery note matches your order.
Open the packaging with suitable tools. Check whether:
- any parts were damaged during transport
- the device type corresponds to your order
Intheeventofanydamageorofan incomplete or incorrect delivery please notify the responsible sales offices immediately.
The devices should only be stored in dry rooms within the specified temperature ranges .
NOTE!Acertain degree of moisture condensation is permissible if this arises from changes in temperature (see
section 3.4.1, “Permissible Environmental Conditions”).This does not, however, apply when the devices
are in operation.Always ensure that there is no moisture condensation in devices that are connected to
the power supply!
3.1.2 Inverter Type Designation
The technical specification of theAGy Drive is stated in the type code. Example:
AGy-EV-2040-KB X-X -X
AGyDrive Evolution series
Drive mechanical dimension
Drive kW rating or Hp (for 575V series)
K=keypad included
X=Software standard
B=Integrated braking unit; X= NOT Integrated braking unit
Mains SupplyType
[Blank]=NOT integrated CANopen/DeviceNet
The AGy Drive selected depends on the rated current of the motor. The rated output current at the appropriate service
conditions must be greater than or equal to the motor current required.
Thespeed of thethree-phasemotor is determinedby thenumber ofpolepairsand thefrequency(nameplate, data sheet)
of the motor concerned. Operation above the rated frequency and speed of the motor must take into account the
specificationsgivenby the manufacturer losses(bearings, unbalance etc.).This also applies to temperaturespecifications
for continuous operation under 20 Hz (poor motor ventilation, not applicable to motors with external ventilation).

14 • Chapter 3 Inspection Procedure, Component Identification and Standard Specification AGy-EV Instruction manual
3.1.3 Nameplate
Check that all the data stated in the nameplate enclosed to the inverter correspond to what has been ordered.
Figure 3.1.3.1: Identification Nameplate (example for 575V series)
Type : AGyEV- 3010 -KBX-5 S/N: 03062492
Inp: 575Vac 50/60Hz 3Ph
15A @575 Vac With line Choke
Out : 0-575Vac 400Hz 3Ph 10Hp @ 575Vac
13,3A @575V Cont. Serv. 12,6A @575Vac Ovld 150%
SHORT CIRCUIT WITH STAND RATING 10KA, 600Vac max
LISTED
INDUSTRIAL CONTROL EQUIPMENT
31KF
®
Type: Inverter model
S/N: Serial number
Main Power In: Power supply voltage - AC Input current - Frequency
Main Power Out: Output voltage - Output current - Output frequency
Figure 3.1.3.2: Firmware & Card Revision Level Nameplate
Firmware HW release S/N 0162330 Prod.
R elease D F P R S BU SW . CFG CONF
C 2.03 A -.A -.- 1.000 A1
Figure 3.1.3.3: Nameplates Position

AGy-EV Instruction manual Chapter 3 Inspection Procedure, Component Identification and Standard Specification • 15
3.2 Component Identification
Figure 3.2.1: Basic Setup of Frequency Inverter
AnAGy Drive converts the constant voltage and frequency of a three-phase power supply into a direct voltage and then
convertsthis direct voltage into a newthree-phase power supply witha variable voltage and frequency.This variable three-
phase power supply can be used for the infinitely variable adjustment of the speed of three-phase asynchronous motors.
1 AC Input supply voltage: 230V ... 480V for “AGy...-4 and 575V for “AGy...-5”.
2 AC Mains choke (see section 5.7.1).
3 Three-phase rectifier bridge
Converts the alternating current into direct current using a three phase full wave bridge.
4 DC intermediate circuit
With charging resistor and smoothing capacitor.
Direct voltage (UDC) = √2 x Mains voltage (ULN)
5 IGBT inverter
Converts direct voltage to a variable three-phase alternating voltage with variable frequency.
6 Configurable control section
Modules for open-loop and closed-loop control of the power section. This is used for processing control commands,
reference values and actual values.
7 Outputvoltage:
Three-phase, variable alternating voltage from 0 up to 94% of Mains voltage (ULN).
8 Encoder(option)
For speed feedback (see section 4.4.2).

16 • Chapter 3 Inspection Procedure, Component Identification and Standard Specification AGy-EV Instruction manual
3.3 Standard Specifications
3.3.1 Permissible Environmental Conditions
Table 3.3.1.1: Environmental Specification
[°C] 0 … +40; +40…+50 with derating
[°F] 32 … +104; +104…+122 with derating
Installation location
Installation altitude
Temperature:
operation
1)
operation
2)
storage
transport
Air humidity:
operation
storage
transport
Air pressure:
operation [kPa] 86 to 106 (class 3K3 as per EN50178)
storage [kPa] 86 to 106 (class 1K4 as per EN50178)
transport [kPa] 70 to 106 (class 2K3 as per EN50178)
General standards
Safety
Climatic conditions
Clearance and creepage
Vibration
EMC compatibility
Rated input voltages
Approvals
TGy0020
-20…+60°C (-4…+140°F), for devices with keypad
IP20 according to EN 60529
IP54 for the cabinet with externallymounted heatsink; onlyfor sizes from 1007 to 3150 (230V…480V) and
from 2002 to 3020 (575V)
EN 50178, UL508C, UL840. Overvoltage categoryfor mains connected circuits: III; degree of pollution 2
EN 60068-2-6, test Fc.
-20…+55°C (-4…+131°F), for devices with keypad
CE, UL, cUL, CSA
ENVIRONMENT
STANDARD
Pollution degree 2 or better (free from direct sunligth, vibration, dust, corrosive or inflammable gases, fog,
vapour oil and dripped water, avoid saline environment)
Up to 1000m (3281 feet) above sea level; for higher altitudes a current reduction of 1.2% for every100m (328
feet) of additional height applies .
A light condensation of moisture mayoccur for a short time occasionallyif the device is not in operation (class 2K3 as per
EN50178)
EN61800-3/A11 (see “EMC Guidelines” instruction book)
IEC 60038
-25…+70°C (-13…+158°F), class 2K3 per EN50178
T
A
Ambient temperature
0…40°C (32°…104°F)
0…50°C (32°…122°F)
-25…+55°C (-13…+131°F), class 1K4 per EN50178
Protection degree
95 %
3)
60 g/m
4)
EN 61800-1, IEC 143-1-1.
5%to85%,1g/m
3
to 25 g/m
3
without moisture condensation or icing (Class 3K3 as per EN50178)
5% to 95 %, 1 g/m
3
to 29 g/m
3
(Class 1K3 as per EN50178)
EN 50178, UL 508C
EN 60721-3-3, class 3K3. EN 60068-2-2, test Bd.
1) Over 40°C (104°F):
- current reduction of 2% of rated output current per K
- remove front plate (better than class 3K3 as per EN50178)
2) Current derated to 0.8 rated ouput current
Over 40°C (104°F): removal of the top cover (better than class 3K3 as per EN50178)
3) Greatest relative air humidity occurs with the temperature @ 40°C (104°F) or if the temperature of the device is
brought suddenly from -25 ...+30°C (-13°...+86°F).
4) Greatest absolute air humidity if the device is brought suddenly from 70...15°C (158°...59°F).

AGy-EV Instruction manual Chapter 3 Inspection Procedure, Component Identification and Standard Specification • 17
Disposal of the Device
The AGy Drive can be disposed as electronic scraps in accordance with the currently valid national regulations for the
disposal of electronic parts.
The plastic covering of the Drives are recyclable: the material used is >ABS+PC< .
3.3.2 Mains Connection and Inverter Output
TheAGy Drive must be connected to an AC mains supply capable of delivering a symmetrical short circuit current lower
or equal to the values indicated on table 3.3.2.1. For the use of anAC input choke see paragraph 5.7.1.
Note from the table of paragraph 3.3.2.1. the allowable mains voltages. The cycle direction of the phases is free.
Voltages lower than the min. tolerance values can cause the block of the inverter.
Itis possible toobtainthe automaticalrestartofthe inverter,afteranotherfailure has occured(For furtherinformation,see
paragraph 7.6,Autoreset Configuration section).
NOTE!Insome casesAC Input chokes, andpossibly noise suppressionfilters should befitted ontheACInput
side of the device. See chapter “Chokes/Filters”.
AdjustableFrequency Drives andACInput filters have ground dischargecurrentsgreaterthan3.5 mA. EN 50178 specifies
that with discharge currents greater than 3.5 mAthe protective conductor ground connection (PE1) must be fixed type.

18 • Chapter 3 Inspection Procedure, Component Identification and Standard Specification AGy-EV Instruction manual
Table 3.3.2.1-A: AC Input/Output Specifications for 230V...480V Drive Kw/Hp Rating
1007 1015 1022 1030 2040 2055 2075 3110 3150 4185 4220 4300 4370 5450 5550 6750 7900 71100 71320 81600 82000
Inverter Output (IEC 146 class1), Continuous service (@ 400Vac) [kVA]
1.6 2.7 3.8 5 6.5 8.5 12 16.8 22.4 27 32 42 55 64 79 98 128 145 173 224 277
Inverter Output (IEC 146 class2),150% overload for 60s (@ 400Vac) [kVA]
1.4 2.4 3.4 4.5 5.9 7.7 10.9 15.3 20.3 24.6 29 38.2 50 58.3 72 89.2 116.5 132 157.5 204 252
P
N
mot (recommended motor output):
@U
LN
=230Vac; f
SW
=default; IEC 146 class 1 [kW]
0.37 0.75 1.1 1.5 2.2 3 4 5.5 7.5 10 11 18.5 22 22 30 37 55 55 75 90 100
@U
LN
=230Vac; f
SW
=default; IEC 146 class 2 [kW]
0.37 0.75 1.1 1.5 2.2 3 4 5.5 7.5 9 11 15 18.5 22 30 37 45 55 55 90 100
@U
LN
=230Vac; f
SW
=default; IEC 146 class 1 [Hp]
0.50 1 1.5 2 3 4 5 7.5 10 10 15 25 30 30 40 50 75 75 100 125 125
@U
LN
=230Vac; f
SW
=default; IEC 146 class 2 [Hp]
0.50 1 1.5 2 3 4 5 7.5 10 10 15 20 25 30 40 50 60 75 75 100 125
@U
LN
=400Vac; f
SW
=default; IEC 146 class 1 [kW]
0.75 1.5 2.2 3 4 5.5 7.5 11 15 18.5 22 30 37 45 55 75 90 110 132 160 200
@U
LN
=400Vac; f
SW
=default; IEC 146 class 2 [kW]
0.75 1.5 2.2 3 4 5.5 7.5 11 15 18.5 22 30 37 45 55 55 90 90 110 160 200
@U
LN
=460Vac; f
SW
=default; IEC 146 class 1 [Hp]
123357.510 1520253040506075100125150150200250
@U
LN
=460Vac; f
SW
=default; IEC 146 class 2 [Hp]
0.75 1.5 2 3 5 7.5 10 15 20 20 25 30 40 50 60 75 100 125 150 200 250
U
2
Max output voltage [V]
f
2
Max output frequency [Hz]
I
2N
Rated output current :
@U
LN
=230-400Vac; f
SW
= default; IEC 146 class 1 [A]
2.4 4 5.6 7.5 9.6 12.6 17.7 24.8 33 39 47 63 79 93 114 142 185 210 250 324 400
@U
LN
=230-400Vac; f
SW
=default; IEC 146 class 2 [A]
2.2 3.6 5.1 6.8 8.7 11.5 16.1 22.5 30 35 43 57 72 85 104 129 168 191 227 295 364
@U
LN
=460Vac; f
SW
=default; IEC 146 class 1 [A]
2.1 3.5 4.9 6.5 8.3 12.1 15.4 23.1 29.7 34 41 55 69 81 99 124 161 183 218 282 348
@U
LN
=460Vac; f
SW
=default; IEC 146 class 2 [A]
1.9 3.2 4.4 5.9 7.6 11.0 14.0 21.0 27.0 31 37 50 63 74 90 112 146 166 198 257 317
f
SW
switching frequency (Default) [kHz]
f
SW
switching frequency (Higher) [kHz]
4-
I
ovld
(short term overload current, 200% of I
2N
for 0.5s on 60s) [A]
4.4 7.2 10.2 13.6 17.4 23 32.2 45 60 70 86 116 144 170 208 258 338 382 454 n.a. n.a.
Derating factor:
Voltage Factor K
V
at 460 Vac **
0.96 0.87 0.93 0.9
Temp. Factor K
T
for ambient temperature
Switching frequency K
F
AC U
LN
Input voltage [V]
AC Input frequency [Hz] I
N
AC Input current for continuous service :
- Connection with 3-phase reactor
@ 230Vac; IEC 146 class 1 [A]
1.7 2.9 4 5.5 * 7 9.5 14 * 18.2 25 * 32.5 39 55 69 84 98 122 158 192 220 275 n.a.
@ 400Vac; IEC 146 class 1 [A]
1.9 3.3 4.5 6.2 * 7.9 10.7 15.8 * 20.4 28.2 * 36.7 44 62 77 94 110 137 177 216 247 309 365
@ 460Vac; IEC 146 class 1 [A]
1.7 2.9 3.9 5.4 * 7 9.3 13.8 * 17.8 24.5 * 32.5 37 53 66 82 96 120 153 188 214 268 318
- Connection without 3-phase reactor
@ 230Vac; IEC 146 class 1 [A]
3.6 4.4 6.8 7.9 * 11 15.5 21.5 * 27.9 35.4 *
@ 400Vac; IEC 146 class 1 [A]
3.9 4.8 7.4 9 * 12 16.9 24.2 * 30.3 40 *
@ 460Vac; IEC 146 class 1 [A]
3.4 4.2 6.4 7.8 * 10.4 14.7 21 * 26.4 34.8 *
Max short circuit power without line reactor (Zmin=1%)
[kVA]
160 270 380 500 650 850 1200 1700 2250 2700 3200 4200 5500 6400 7900 9800 12800 14500 17300 22400 27700
Overvoltage threshold [V]
Undervoltage threshold [V]
Braking IGBT Unit
Standard internal (with external resistor); MAX Braking torque :
TGy0031gb
50/60 Hz ±5%
230 V -15% … 480 V +10%, 3Ph
440VDC (for 230VAC mains), 820VDC (for 400VAC mains), 820VDC (for 460VAC mains)
For these types an external inductance is recommended
230VDC (for 230VAC mains), 380VDC (for 400VAC mains), 415VDC (for 460VAC mains)
Option internal (with external resistor);
Braking torque 150%
150%
AGy Drive Type - kW rating
OUTPUT
8
0.8 @ 50°C (122°F)
200500
8
16
External braking unit (optional)
4
0.94 x U
LN
(AC Input voltage)
0.87
INPUT
0.87
0.7 for higher f
sw
*: For the specified power sizes, the external reactor is strongly recommended
**: Linear shapes for KV, KT, respectively in the ranges [400, 460] Vac, [40, 50]°C, (104, 122)°F.
Example: for AC mains = 440VAC, 400V/440V = 0.90 = KV

AGy-EV Instruction manual Chapter 3 Inspection Procedure, Component Identification and Standard Specification • 19
Table 3.3.2.1-B: AC Input/Output Specifications for 575V Drive Hp Rating
AGy Drive Type - Hp rating 2002 2003 2005 3007 3010 3015 3020 4025 4030 4040 5050 5060 5075 6100 7125 7150 8200
Inverter Output (IEC 146 class1), Continuous service
[kVA] 3.8 4.5 7.0 10.8 13.7 18.6 24.1 30 36 46 58 69 86 109 136 157 210
Inverter Output (IEC 146 class2), 150% overload for 60s
[kVA] 3.4 4.1 6.3 9.8 12.5 16.9 21.9 27 33 42 53 63 78 99 124 143 191
P
N
mot (recommended motor output):
@U
LN
=575Vac; f
SW
=default; IEC 146 class 1
[Hp] 2 3 5 7.5 10 15 20 25 30 40 50 60 75 100 125 150 200
@U
LN
=575Vac; f
SW
=default; IEC 146 class 2
[Hp] 2 3 5 7.5 10 15 20 25 30 40 50 60 75 100 125 150 200
U
2
Max output voltage
[V]
f
2
Max output frequency (*)
[Hz]
I
2N
Rated output current :
@U
LN
=575Vac; f
SW
= default; IEC 146 class 1
[A] 3.8 4.5 7.0 10.8 13.8 18.7 24.2 30 36 46 58 69 86 109 137 158 211
@U
LN
=575Vac; f
SW
=default; IEC 146 class 2
[A] 3.5 4.1 6.4 9.8 12.6 17.0 22.0 27 33 42 53 63 78 99 125 144 192
f
SW
switching frequency (Default)
[kHz]
f
SW
switching frequency (Higher)
[kHz] 2
I
ovld (short term overload current, 200% of I2N for 0.5s on 60s) [A] 7.0 8.2 12.8 19.6 25.2 34 44 54 66 84 106 126 156 198 249 288 384
Derating factor:
K
T
for ambient temperature
K
F
for switching frequency
0.87 0.64 0.87 n.a.
U
LN
AC Input voltage
[V]
AC Input frequency
[Hz]
I
N
AC Input current for continuous service :
- Connection with 3-phase reactor
@ 575Vac; IEC 146 class1
[A] 3.8 4.7 7.4 11.7 15 19.8 25.9 31 35 46 60 68 85 114 140
163 216
- Connection without 3-phase reactor
@ 575Vac; IEC 146 class1
[A] 5.3 6.1 9.9 17 20.7 27.6 33.9
Max short circuit power without line reactor (Zmin=1%)
[kVA] 380 450 700 1080 1370 1860 2410 3000 3600 4600 5800 6900 8600 10900 13700 15700 21000
Overvoltage threshold
[V]
Undervoltage threshold
[V]
Braking IGBT Unit (standard drive)
TGy0030
n.a.
0.8 for higher f
SW
OUTPUT
400
42
4
1000 VDC
565 VDC (for 575 VAC mains)
External braking unit (optional)
Optional internal braking unit (with external
resistor); braking torque 150%
Standard internal (with external resistor); Braking torque
150%
DC choke integrated
0.94 x ULN (AC Input voltage)
8
200
16
8
INPUT
0.7 for higher f
SW
0.8 @ 50°C (122°F)
500 -10% / 575V ±10%, 3Ph
50/60 Hz ±5%

20 • Chapter 3 Inspection Procedure, Component Identification and Standard Specification AGy-EV Instruction manual
3.3.3 AC Input Current
NOTE!The Input current of the Drive depends on the operating state of the connected motor. The tables
3.3.2.1 shows the values corresponding to rated continuous service, keeping into account typical
output power factor for each size
3.3.4 AC Output
The output of theAGy Drive is ground fault and phase to phase output short protected.
NOTE!Theconnectionofanexternalvoltagetotheoutputterminalsofthe Drive is notpermissible!Itisallowed to
disconnect the motor from the Drive output, after the Drive has been disabled.
Therated value ofdirect currentoutput (ICONT ) dependson thesupply voltage(KV), the ambient temperature( KT)and the
switching frequency (KF) if higher than the default setting:
ICONT = I2N x KVx KT(Values of derating factor are the listed on tables 3.3.2.1) with an overload capacity IMAX = 1.5 x ICONT
for 60 seconds.
Recommended motor outputs
The coordination of the motor rated powers with the Drive type presented in the table 3.3.2.1 refers to the use of standard
motors with a rated voltage equal to the rated voltage of the input supply.
As for those motors with different voltages, the type of Drive to use is determined by the rated current of the motor.
NOTE!Max allowed overload:
136% . I2N cl.1 ≡150% . I2N cl.2
Table 3.3.4.1 shows nominal current values for typical service profiles (Ambient temperature =40°C
[104°F], standard switching frequency).
Similar criteria apply for operation with additional derating factors.
Table 3.3.4.1: Nominal Drive Current
I2N (1) I2N (2) I2N (3) I2N (4) I2N (5) I2N (6)
[A] [A] [A] [A] [A] [A]
1007 2.4 2.2 2.1 1.9 2002 3.8 3.5
1015 4.0 3.6 3.5 3.2 2003 4.5 4.1
1022 5.6 5.1 4.9 4.4 2005 7.0 6.4
1030 7.5 6.8 6.5 5.9 3007 10.8 9.8
2040 9.6 8.7 8.3 7.6 3010 13.8 12.6
2055 12.6 11.5 12.1 11 3015 18.7 17.0
2075 17.7 16.1 15.4 14 3020 24.2 22.0
3110 24.8 22.5 23.1 21.0 4025 30 27
3150 33 30 29.7 27 4030 36 33
4185 39 35 34 31 4040 46 42
4220 47 43 41 37 5050 58 53
4300 63 57 55 50 5060 69 63
4370 79 72 69 63 5075 86 78
5450 93 85 81 74 6100 109 99
5550 114 104 99 90 7125 137 125
6750 142 129 124 112 7150 158 144
7900 185 168 161 146 8200 211 192
71100 210 191 183 166
71320 250 227 218 198
81600 324 295 282 257
82000 400 364 348 317
TGy0040gb
AGy…-4 (230V…480V)
Drive TypeDrive Type
AGy…-5 (575V)
(1): I2N Rated output current (@ ULN=230-400Vac),
Continuous service, no overload (IEC 146 class 1)
(2): I2N Rated output current (@ ULN=230-400Vac), Overload
service150%x60sfollowedbyIN,min.cycletime360s(IEC
146 class 2).
(3): I2N x kV Rated output current (@ ULN=460-480Vac),
Continuous service, no overload (IEC 146 class 1)
(4): I2N x kV Rated output current (@ ULN=460-480Vac),
Overload service 150%x60s followed by IN, min.cycle time
360s (IEC 146 class 2).
(5) I2N Rated output current (@ ULN=575Vac), continuous
service, no overload (IEC 146 classe 1).
(6) I2N Rated output current (@ ULN=575Vac), overload
service 150%x60s followed by IN, min. cycle time 360s
(IEC 146 classe 2).