Gemini Gem-p9600 Installation manual

HARDWIRE WIRELESS

GEM-P9600

CONTROL PANEL/COMMUNICATOR

Programming the GEM-P9600 Control Panel with the

"Classic" GEM-RP2ASe2, GEM-RP3DGTL, and GEM-RP4RFC/GEM-RP4C Keypads and

the "K Series" GEM-K2AS, GEM-K3DGTL, and GEM-K4RF/GEM-K4 Keypads

WI 1185 6/03

PROGRAMMING

INSTRUCTIONS

"K Series" GEM-K2AS

COMPUTERIZED SECURITY SYSTEM

ARMED

STATUS

SYSTEM ARMED

01/01/97 12:00AM

7890

NEXT/YES

PRIOR/NO

AREA

GEMINI

READY

AC ON

READY

AC ON

COMPUTERIZED SECURITY SYSTEM

ARMED

STATUS

SYSTEM ARMED

01/01/97 12:00AM

7890

NEXT/YES

PRIOR/NO

AREA

GEMINI

ENT A1

INT E RIO R BYPASS FIRE/TBL SYS TBL CHIME

"K Series" GEM-K3DGTL

Quick Start (for GEM-K2ASe2):

1. Refer to the wiring diagram, connect Siren, Aux. Power,

PGM Output, Remote Bus, Earth Ground, Zone and Tele-

phone Wiring. NOTE: See Installation Instructions (WI742).

2. Connect AC power first and then the battery.

3. Configure the keypad (see page 64).

4. Access the Easy Menu Driven (Dealer Program) Mode:

Press:

EEEEEER

Press NO until “TURNON PROG Y/N” appears on the keypad display.

Press NEXT/YES to enter Dealer Program Mode. See p. 5

Master Security Code

(on microshield)

Quick Start (for GEM-K3DGTL):

1. Refer to the wiring diagram, connect Siren, Aux. Power,

PGM Output, Remote Bus, Earth Ground, Zone and Tele-

phone Wiring. NOTE: See Installation Instructions (WI742).

2. Connect AC power first and then the battery.

3. Configure the keypad (see page 64).

4. Access the Easy Menu Driven (Dealer Program) Mode:

Press:

EEEEEER

Press NO until “17” appears on the keypad display.

Press NEXT/YES to enter Dealer Program Mode. See p. 5.

Master Security Code

(on microshield)

"K Series" GEM-K4RF/GEM-K4

THIS MANUAL INCLUDES FEATURES WHICH ARE ONLY AVAILABLE IN CONTROL PANEL FIRMWARE

VERSION 20 OR LATER.

IMPORTANT NOTE

This manual supports the keypad programming of the GEM-P9600 control panel with the NAPCO "classic" GEM-

RP2ASe2, GEM-RP3DGTL and GEM-RP4RFC/GEM-RP4C keypads as well as the GEM-K2AS, GEM-K3DGTL and

GEM-K4RF/GEM-K4 "K Series" keypads. The new "K Series" models offer the new STAY and AWAY buttons with sim-

plified functionality, along with the new MENU and ENTER buttons. While the instructions in this manual are depicted

using the "K Series" keypads, the manual applies to both the "classic" and the "K Series" keypads.

Program Mode is the same for both keypads--only the button names have changed, as follows:

•The Abutton and the Rbutton operate identically (in Program Mode) for both keypads.

•The Dbutton and the Ubutton operate identically (in Program Mode) for both keypads.

•The button and the button operate identically (in Program Mode) for both keypads. The words

"NEXT/YES button" are used in this manual.

•The button and the button operate identically (in Program Mode) for both keypads. The words

"PRIOR/NO button" are used in this manual.

CHANGES FROM PREVIOUS EDITION

This manual (WI1185) contains revised Installation Instructions previ-

ously found in WI777D. The revisions are as follows:

Pages 6-21: Easy Program Menu includes new selections: 24 Hour Zones in

Area 1, Chime Zones in Area 1, Chime 2 Zones in Area 1, Exit/Entry2

Zones in Area 1, 50 mS Loop Response Zones, Aux Output Activated on

Alarm Zones, Sensor Watch Zones, Keypad Sounder On Alarm Zones,

Auto Bypass Re-entry Zones, Enable No EOLR Zones, Enable Telco Line

Fault Test, Enable Burg Output Chirp on KeyFob, Enable SIA CP-01 Fea-

tures.

Page 39, address 2421, "Telco Answering Service Override" name changed to

"2nd Call Answering Machine Override".

Page 46, added address 2417, bit 5, "Lug E4 Armed Away Only".

Panel includes added features to accommodate the SIA CP-01 False Alarm Re-

duction Standard. Therefore Direct Address Program Mode addresses

have been modified or added, as follows:

Page 47, modified address 2422, bit 6, Enable Bell Output on Keyfob Arming

Page 47, added address 2421, bit 3, Aux. Output Chirp on Keyfob Arm/Disarm

Page 47, added address 2421, bit 4, Don’t Clear Aux. Relay with Disarm

Page 48, added address 3905, bit 1, Exit Time Restart

Page 48, added address 3905, bit 2, Sound Alarm on Exit Error

Page 48, added address 3905, bit 3, Rpt Exit Err/Recent Close

Page 48, added address 3905, bit 4, Digital Dialer Rpt Enter/Exit Test Mode

Page 48, added address 3905, bit 5, Enable CP-01 Limits

Page 48, added address 3905, bit 6, Disable Call Waiting on First Attempt

Page 48, added address 3905, bit 7, Enable Ambush in User Assignment

Code Type

Page 28, modified address 4082, Report Cancel Window.

Address Number Index added at end of manual.

Page 4, the following statement added: "Note: Unattended downloading from a

computer is not allowed for Fire Alarm or UL installations."

Pages 4, 5, and 7, "50mS Loop Response Zones", since the time of 50 mS does

not meet the UL listing requirement of the panel, the following notation is

made: "750 mS is required for Loop Response time in UL installations".

Page 7, "Auto Bypass Re-entry Zones" notation added: "Not evaluated by UL".

Page 10, "Enter User Codes", instructions modified to enter a code from "3 to 6"

digits.

Area Options/Explanation chart at the top of page 11: the following information

added: "Ambush: Allows user code to send Ambush signal to Central

Station".

In Zone Options (pages 40-45) and the wiring diagram (page 72), the following

notation added: "Disable Auto-Reset on non-fire zones for SIA CP-01 in-

stallations".

Added to Zone Options (pages 40-45) and on page 47, address 2422, bit 0: "In UL

installations, all Fire Zones must also be programmed for 'Pulsed Burg

Output' and 'Fire Output Cadence' (Address 2422, bit zero)".

Page 59, Table 4: the following notation added: "Keypad Tamper must be en-

abled in UL installations".

Pages 40-44, added to Zone Options, "Interior (STAY) Bypass", addresses 1284,

1384, 1484, 1584, 1684, 1784, 1884, 1984, 2084, 2184, 2284, 2384.

Page 46, notation added to address 2419, bit 0: "*Do not use on systems with "K

Series " keypads".

Page 47, address 2422, bit 5, "Disable Exit/Entry Urgency Tone at Keypad"

changed to "Disable Entry Urgency Tone at Keypad".

NAPCO Security Systems, Inc.

333 Bayview Avenue, Amityville, New York 11701

For Sales and Repairs, call toll free: (800) 645-9445

For direct line to Technical Service,

call toll free: (800) 645-9440

Internet: http://www.napcosecurity.com

LNAPCO Security Systems XGEM-P9600 Programming Instructions

Page 3

WI 1185 6/03

TABLE OF CONTENTS

Refer to accompanying GEM-P9600 Installation Instructions (WI742) for installation information.

IMPORTANT NOTE................................................................................................................................2

CHANGES FROM PREVIOUS EDITION...............................................................................................2

SYSTEM PROGRAMMING OPTIONS ..................................................................................................4

Introduction ....................................................................................................................................4

Downloading From a Computer ....................................................................................................4

EASY MENU DRIVEN PROGRAM MODE............................................................................................5

Dealer Program - Preliminary Information ....................................................................................5

Accessing Dealer Program Mode..................................................................................................5

Customizing a Default Program ....................................................................................................5

GEM-RP2ASe2/GEM-K2AS KEYPAD Easy Program Menu..............................................6

Total Number of Zones in Area 1 .................................................................................6

Total Number of Zones in Area 2 .................................................................................6

Fire Zones in Area 1......................................................................................................6

2-Wire Fire Zones in Area 1..........................................................................................6

Local or Central Station Reporting System..................................................................6

Exit/Entry Zones in Area 1 ............................................................................................6

Interior Zones in Area 1 ................................................................................................6

24 Hour Zones in Area 1...............................................................................................7

Chime Zones in Area 1 .................................................................................................7

Chime 2 Zones in Area 1 ..............................................................................................7

Exit/Entry2 Zones in Area 1 ..........................................................................................7

50mS Loop Response Zones ....................................................................................... 7

Aux Output Activated on Alarm Zones .........................................................................7

Sensor Watch Zones ....................................................................................................7

Keypad Sounder on Alarm Zones ................................................................................7

Auto Bypass re-entry Zones .........................................................................................7

Enable no EOLR Zones................................................................................................8

Enable Telco Line Fault Test........................................................................................8

Enable Burg Output Chirp on Keyfob ...........................................................................8

Enable SIA CP-01 Features .........................................................................................8

Number of Keypads in Area 1.......................................................................................8

Number of Keypads in Area 2.......................................................................................8

Central Station Receiver 1 Tel. Number.......................................................................8

Easy Programming of Auto download ID #'s and PC Preset Callback Numbers .......9

Central Station Receiver 1 Account Number ...............................................................9

Central Station Receiver 1 Format ...............................................................................9

Enter User Codes.......................................................................................................... 10

RF Transmitter Points ...................................................................................................12

Quick Method ................................................................................................................12

Key Fob Transmitters (as Arm/Disarm & Control Devices) .........................................12

Key Fob Transmitters (as Zone Input Devices) ...........................................................13

Enter Zone Descriptions ...............................................................................................13

Enter Date .....................................................................................................................13

Enter Time .....................................................................................................................13

Dealer Code ..................................................................................................................13

Exit Dealer Program Mode ...........................................................................................13

Clear Dealer Program ................................................................................................... 13

Cold Start....................................................................................................................... 13

GEM-RP3DGTL/GEM-K3DGTL and GEM-RP4RFC/GEM-K4RF KEYPAD Easy

Program Menu 14

Total Number of Zones in Area 1 .................................................................................14

Total Number of Zones in Area 2 .................................................................................14

Fire Zones in Area 1......................................................................................................14

2-Wire Fire Zones in Area 1..........................................................................................14

Local or Central Station Reporting System..................................................................14

Exit/Entry Zones in Area 1 ............................................................................................14

Interior Zones in Area 1 ................................................................................................15

24 Hour Zones in Area 1...............................................................................................15

Chime Zones in Area 1 .................................................................................................15

Chime 2 Zones in Area 1 ..............................................................................................15

Exit/Entry2 Zones in Area 1 ..........................................................................................15

50mS Loop Response Zones .......................................................................................15

Aux Output Activated on Alarm Zones ......................................................................... 15

Sensor Watch Zones ....................................................................................................15

Keypad Sounder on Alarm Zones ................................................................................16

Auto Bypass re-entry Zones .........................................................................................16

Enable no EOLR Zones................................................................................................16

Enable Telco Line Fault Test........................................................................................ 16

Enable Burg Output Chirp on Keyfob ...........................................................................16

Enable SIA CP-01 Features .........................................................................................16

Number of Keypads in Area 1.......................................................................................16

Number of Keypads in Area 2.......................................................................................16

Central Station Receiver 1 Tel. Number.......................................................................17

Central Station Receiver 1 Account Number ...............................................................17

Central Station Receiver 1 Format ...............................................................................17

Enter User Codes.......................................................................................................... 18

RF Transmitter Points ...................................................................................................20

Quick Method ................................................................................................................20

Key Fob Transmitters (as Arm/Disarm & Control Devices)......................................... 20

Key Fob Transmitters (as Zone Input Devices) ........................................................... 21

Enter Zone Descriptions ............................................................................................... 21

Enter Date .....................................................................................................................21

Enter Time.....................................................................................................................21

Dealer Code.................................................................................................................. 21

Exit Dealer Program Mode ........................................................................................... 21

Clear Dealer Program................................................................................................... 21

Cold Start ...................................................................................................................... 21

DIRECT ADDRESS PROGRAM MODE.................................................................................................. 22

Keypad Programming Overview ..................................................................................................... 22

Accessing Direct Address Program Mode ...................................................................................... 22

Keypad Address Program Mode Display........................................................................................ 23

Direct Address Program Mode Keypad Commands ...................................................................... 23

Conventions Used in this Manual ................................................................................................... 25

PROGRAMMING OPTIONS & WORKSHEETS ..................................................................................... 27

SYSTEM DELAYS & TIMEOUTS (ADDRESS 0000-0002, 2402, 2406, 2414 & 3902).................27

SYSTEM DELAYS & TIMEOUTS (ADDRESS 2407, 2408 & 4088) ..............................................27

SYSTEM DELAYS & TIMEOUTS (ADDRESS 2400, 2401, 2403-2405, 4082 & 4083)................. 28

KEYPAD SYSTEM CODES (ADDRESS 0490, 0495 & 0500) .......................................................28

CS RECEIVER FORMAT OPTIONS (ADDRESS 0520, 0521, 0525, 0526, 0550, 0551,

0575 & 0576) ........................................................................................................................ 29

CS RECEIVER TELEPHONE NUMBERS (ADDRESS 0527-0546, 0552-0571, 0577-0596)....... 30

DOWNLOAD/CALLBACK OPTIONS (ADDRESS 4089, 0600-0619, 0625-0647, 1022 &

1023)..................................................................................................................................... 30

CS SUBSCRIBER ID NUMBERS (ADDRESS 0650-0787)............................................................ 31

CS SUBSCRIBER ID NUMBERS (ADDRESS 0790-0857) ............................................................ 32

CS REPORTING CODES (ADDRESS 0859-0907) ........................................................................ 32

CS REPORTING CODES (ADDRESS 0870-0904) ........................................................................ 33

CS AREA & SYSTEM REPORTING OPTIONS (ADDRESS 1024-1027)...................................... 33

CS ZONE REPORTING CODES (ADDRESS 0910-1005)............................................................. 34

CS USER REPORTING CODES (ADDRESS 1030-1055)............................................................. 35

CS USER REPORTING CODES (ADDRESS 1056-1081)............................................................. 36

GLOBAL SYSTEM TROUBLE REPORTING OPTIONS (ADDRESS 1082-1116) ........................ 37

AREA SYSTEM TROUBLE REPORTING OPTIONS (ADDRESS 1120-1157)............................. 38

AREA SYSTEM TROUBLE REPORTING OPTIONS (ADDRESS 1160-1197)............................. 39

ZONE OPTIONS / ZONES 1-16 (ADDRESS 1200-1386) ..............................................................40

ZONE OPTIONS / ZONES 17-32 (ADDRESS 1402-1586) ............................................................41

ZONE OPTIONS / ZONES 33-48 (ADDRESS 1602-1786) ............................................................ 42

ZONE OPTIONS / ZONES 49-64 (ADDRESS 1802-1986) ............................................................43

ZONE OPTIONS / ZONES 65-80 (ADDRESS 2002-2186) ............................................................44

ZONE OPTIONS / ZONES 81-96 (ADDRESS 2202-2386) ............................................................ 45

ZONE OPTIONS / ZONES 1-96 (ADDRESS 1200-2386) .............................................................. 46

SYSTEM OPTIONS (ADDRESS 2415-2419).................................................................................. 48

SYSTEM OPTIONS (ADDRESS 2420-2422, 3874 & 3879-3881)................................................. 49

ALARM/TROUBLE REPORTING CODES (ADDRESS 3879-3881)..............................................50

SYSTEM OPTIONS (ADDRESS 3882-3901, 3903-3905 & 4084) .................................................50

KEYPAD OPTIONS (ADDRESS 2425-2454).................................................................................. 51

USER AREA OPTIONS (ADDRESS 2500-2595) ........................................................................... 52

EZM GROUP OPTIONS (ADDRESS 2600-2621) ..........................................................................53

AREA ARMING OPTIONS (ADDRESS 2650-2657)....................................................................... 54

REMOTE ACCESS LOGGING (ADDRESS 3184).......................................................................... 54

AREA OUTPUT CONTROL OPTIONS (ADDRESS 2700-2739) ...................................................55

RF RECEIVERS & SUPERVISORY TIMER OPTIONS (ADDRESS 3776 & 3760-3775) ............. 56

EXTERNAL RELAY CONTROL / RELAYS 1-39 (ADDRESS 3778-3816 & 2800-2955) .............. 57

EXTERNAL RELAY CONTROL / RELAYS 40-78 (ADDRESS 3817-3855 & 2856-3111) ............ 58

EXTERNAL RELAY CONTROL / RELAYS 79-96 (ADDRESS 3856-3873 & 3112-3183) ............59

NUMBER OF RELAY BOARD MODULES (ADDRESS 3777) ....................................................... 62

SYSTEM RESET OPTIONS (ADDRESS 4091-4093) ....................................................................63

USER PROGRAM MODE ........................................................................................................................ 64

Preliminary Information ................................................................................................................... 64

Accessing User Program Mode ...................................................................................................... 64

User Codes...................................................................................................................................... 65

KEYPAD CONFIGURATION MODE ....................................................................................................... 66

Configuring the Keypads ................................................................................................................. 66

ALPHABETICAL INDEX.......................................................................................................................... 67

ADDRESS NUMBER LOCATION INDEX............................................................................................... 72

GEM-P9600 WIRING DIAGRAM ............................................................................................................. 76

XGEM-P9600 Programming Instructions LNAPCO Security Systems

!Page 4 WI 1185 6/03

SYSTEM PROGRAMMING OPTIONS

INTRODUCTION

The GEM-P9600 control panel may be programmed by various means, each of which will be covered in detail in the sections

that follow. Keypad displays shown are for a GEM-K2AS, the GEM-K3DGTL, and the GEM-K4/GEM-K4RF series. With the

GEM-RP2ASe2/GEM-K2AS keypads, because of their reduced display capabilities, messages are abbreviated and will scroll

through two or more screens. Zone descriptions cannot be programmed using GEM-K2AS/GEM-RP2ASe2, GEM-K3DGTL/

GEM-RP3DGTL, nor a GEM-K4RF/RP4RFC series keypad, therefore a GEM-RP1CAe2 or GEM-K1CA keypad must be used.

!Downloading From a Computer. This is the preferred method of programming. The panel may be downloaded

from (or uploaded to) an IBM PC-compatible computer, either locally or remotely. Napco's PCD-Windows

Quickloader software features context-sensitive help screens as well as an error-checking utility that prevents

programming of incompatible or conflicting data to ensure proper panel operation. Note: Unattended download-

ing from a computer is not allowed for Fire Alarm or UL installations.

!Easy Menu-Driven Program (Dealer Program) Mode - Keypad Programming. The Easy Menu-Driven

Program Mode allows keypad programming of number of zones in area 1 and 2, panel zone doubling, number of

fire zones (both 4-wire and 2-wire), local or Central Station reporting, number of exit/entry zones, number of inte-

rior zones, number of 24 hour zones, number of chime zones, Chime 2 zones, Exit/Entry2 zones, 50ms loop re-

sponse zones (Note: 750mS is required for Loop Response time in UL installations), aux output activated on alarm

zones, sensor watch zones, keypad sounder on alarm zones, auto bypass re-entry zones, EOLR zones, number of

keypads in area 1 and 2, Central Station telephone number, Central Station account number, Central Station re-

ceiver format, User Codes, RF transmitter points, RF keyfob transmitters, zone descriptions, dealer code, Telco

line fault test, Burg output chirp on keyfob, enable CP-01, and clear dealer program/cold start. For new panels, a

custom default program may be created at the keypad. A menu-driven utility prompts the installer to configure the

system. Further detailed customization is accomplished in the Direct Address Program Mode.

!Direct Address (Dealer Program) Program Mode - Keypad Programming. The Direct Address Program Mode

is an extension of the Dealer Program Mode wherein data is entered at the keypad by specific location. This mode

is accessed from the Easy Menu Driven Program Mode by pressing the Cbutton at any time.

!User Program Mode - Keypad programming. The User Program Mode is intended for authorized users and is

limited to keypad programming of User Codes, Time, Date and Zone Descriptions.

DOWNLOADING FROM A COMPUTER

The control-panel program may be downloaded from the computer by any of the following methods.

Local Downloading

(Note: This procedure should be used after installation, after peripheral devices are connected).

For direct high-speed data transfer to the control panel from a desktop computer, connect the download jack (JP2)

on the panel to the LOCAL jack (J3) on the Napco PCI2000/3000 computer interface using the supplied 6-

conductor cable. (Refer to PCI2000/3000 Installation Instructions WI443 for wiring diagram and procedures).

Similarly, a high-speed local download may be made in the field using a notebook or laptop computer. Connect

JP2 on the control panel to a Napco PCI-MINI computer interface using the 6-conductor cable supplied. (Refer to

PCI-MINI Installation Instructions WI767).

Remote Downloading

(Also see PCI2000/3000 Installation Instructions WI443).

Function Mode.

Start by establishing a telco connection between the computer operator and the installer. During this procedure,

voice contact will be lost, therefore both the installer and the computer operator should be familiar with the

operation. When a steady high-pitched tone is heard at the site phone, access the “ACTIVATE DOWNLOAD” Function

(see Keypad Programming Modes), then press the Ubutton or the YES button; the site phone will go dead. Hang

up the phone and wait for a call from the central station confirming a successful download.

Callback Method.

An installed, unattended panel may be programmed or reprogrammed remotely using the Callback-Method

Download feature of the PCD Windows software. Remote downloading requires a modem compatible with the

PCI2000/3000. Upon answering the call from the computer, the panel will verify the Download Security Code and,

if confirmed, will establish a connection. If a Callback Number is programmed into the panel, the panel will

automatically disconnect and call the computer at this number before establishing a connection.

SYSTEM PROGRAMMING OPTIONS

LNAPCO Security Systems XGEM-P9600 Programming Instructions

Page 5

WI 1185 6/03

EASY MENU DRIVEN PROGRAM MODE

DEALER PROGRAM - PRELIMINARY INFORMATION

!Only Keypad #1 may be used for both Dealer and User programming, however this keypad may be located in any area.

!The Master Security Code is printed on the panel’s microprocessor can. Use this code to enter the Dealer Program Mode to program a

custom Dealer Security Code. Record the number, then remove the code label to prevent unauthorized access to the panel. If you forget

your Dealer Security Code, use the Master Security Code to enter programming.

!After entering codes or data, press the save Ubutton. Data will not be stored into memory unless Uis pressed.

!If the keypad is in the Program Mode and no activity is detected for longer than 4 minutes, a steady tone will sound.

!Silence the sounder by the Gbutton to continue, or by pressing the Cbutton to exit.

!A panel that has been COLD STARTED (Address Location 4093) performs identically to a new panel.

!When programming a Multiple Area System, Direct Address Programming Mode must be used to complete the program.

KEYPAD #1: For ease of programming, it is recommended that a GEM-RP1CAe2 or GEM-K1CA be used as Keypad #1.

(Regardless of which keypad is selected, all new keypads are configured as Keypad #1 out of the box). If a GEM-RP2ASe2/

GEM-K2AS is used, configure address jumpers as Keypad #1 (see Configuring the GEM-RP2ASe2 Keypad, page 64).

1. Press EEEEEE R

2. Press "PRIOR/NO" button until “TURNON PROG Y/N” (GEM-RP2ASe2/

GEM-K2AS) or “17”(GEM-RP3DGTL/GEM-K3DGTL or

GEM-RP4RFC/GEM-K4RF) appears on the LCD screen.

3. Press "NEXT/YES" button to Enter Dealer Program Mode.

4. Press CC to exit Dealer Program Mode when finished.

•Number of Zones in Area 1

•Number of Zones in Area 2

•Fire Zones in Area 1

•2-Wire Fire Zones in Area 1

•Local or Central Station Reporting System

•Exit/Entry Zones in Area 1

•Interior Zones in Area 1

•24 Hour Zones in Area 1

•Chime Zones in Area 1

•Chime 2 Zones in Area 1

•Exit/Entry2 Zones in Area 1

•50mS Loop Response Zones (Note: 750mS is

required for Loop Response time in UL installations).

•Aux Output Activated on Alarm Zones

•Sensor Watch Zones

•Keypad Sounder on Alarm Zones

•Auto Bypass re-entry Zones

•Enable no EOLR Zones

•Number of Keypads in Area 1 and 2

•Central Station Receiver 1 Tel. Number

•Central Station Receiver 1 Account Number

•Central Station Receiver 1 Format

•Enter User Codes

•RF Transmitter Points

•Quick Method

•Key Fob Transmitters

•Enter Zone Descriptions

•Dealer Code

•Enable Telco Line Fault Test

•Enable Burg Output Chirp on Keyfob

•Enable CP-01

•Clear Dealer Program

•Cold Start

NEW PANELS: The custom default program may be created for new panels only. Once the panel has been programmed by any

means, the number zones will be suppressed and cannot be changed. Should it be necessary to create a new custom default

program, (a) from the Dealer Program Mode, press the Cbutton to enter the Direct Address Program Mode; (b) access Location

4091 (Clear Program); (c) press the Ubutton and start over.

EASY MENU DRIVEN PROGRAM MODE

ACCESSING DEALER PROGRAM MODE

CUSTOMIZING A DEFAULT PROGRAM

For new panels, you can design a default program that will best suit your application. Using this procedure, you will configure the panel for:

This procedure will automatically set up system keypads, EZMs, wireless transmitters, etc. After your basic default program has been

loaded, you may alter it as necessary in the Direct Address Program Mode.

Master Security Code

(on microshield)

GEM-P3200

CONTROL

COMMUNCIATOR

MASTER SECURITY CODE

# - # - # - # - # - #

GEM-P9600

XGEM-P9600 Programming Instructions LNAPCO Security Systems

!Page 6 WI 1185 6/03

GEM-RP2ASe2/GEM-K2AS Keypad Easy Program Menu

Enter the Dealer Security Code (default = 456789) for a new panel or enter your custom Dealer Program Code if

programmed. Press the PRIOR/NO button repeatedly until “TURNON/PROG” is displayed. NOTE: If you pass “TURNON/

PROG”, you can scroll back by pressing B. Press the NEXT/YES button to enter the Dealer Program Mode. In

each of the following steps, press Rto jump to the next screen, the NEXT/YES button to go forwards, the

PRIOR/NO button to go backwards, Uto save and Ctwice to exit at any time.

Total Number of Zones in Area 1 (New Program Only)

•Enter the total number of zones to be programmed for Area 1.

•Valid entries are from 01 to 96. Directly enter the total number of zones, including leading zeros.

•The system is based on groups of 4 zones each (after the first 8 zones), and will automatically round up to the next

group of 4. For example, if you enter 18, it will automatically convert this to 20 zones. Press Uto save. Press the

NEXT/YES button to proceed.

Total Number of Zones in Area 2 (New Program Only)

•Enter the total number of zones to be programmed for Area 2.

•Valid entries are from 01 to 96. Directly enter the total number of zones, including leading zeros.

•The system is based on groups of 4 zones each (after the first 8 zones), and will automatically round up to the next

group of 4. For example, if you enter 18, it will automatically convert this to 20 zones. Press Uto save. Press the

NEXT/YES button to proceed.

Fire Zones in Area 1 (New Program Only)

•Enter the zone number of any Fire Zones (including 2-wire, 4-wire or wireless).

•Valid entries are from 01 to 96.

•Directly enter each zone number, including leading zeros, and press Uto save, and then repeat for any additional

zone(s). Press the NEXT/YES button to proceed.

2-Wire Fire Zones in Area 1 (New Program Only)

•Enter the zone number of any Fire Zone (from previous question) to be used with 2-wire smoke detectors.

•Valid entries are 07 and 08. Directly enter each zone number, including leading zeros.

•Press Uto save, and repeat for any additional zone(s); press NEXT to proceed.

NOTE: Only zones which have been designated as Fire Zones can be programmed as 2 Wire Fire zones. JP3 must

be set to “2-WF” position for 2-wire fire. (refer to Installation Instructions).

Local or Central Station Reporting System (New Program Only)

Press the NEXT/YES button for all zones to report; press the PRIOR/NO button for local system.

Exit/Entry Zones in Area 1 (New Program Only)

•Enter the zone numbers of zones to be used as Exit/Entry zones.

•Valid entries are from 01 to 96. Directly enter each zone number, including leading zeros.

•Press Uto save and repeat for any additional zone(s); press the NEXT/YES button to proceed.

NOTE: Exit/Entry Entry time of 30 seconds will automatically be programmed.

Interior Zones in Area 1 (New Program Only)

•Enter the zone numbers to be used as Interior Zones.

•Valid entries are from 01 to 96. Directly enter each zone number, including leading zeros.

•Press Uto save and then repeat for any additional zone(s).

•Press the NEXT/YES button to proceed.

•All Interior zones will also be automatically programmed as “Exit/Entry Follower” and as "Power Up Delay" zones.

COMPUTERIZED SECURITY SYSTEM

ARMED

STATUS

SYSTEM ARMED

01/01/97 12:00AM

7890

NEXT/YES

PRIOR/NO

AREA

GEMINI

ENT A1

GEM-RP2ASE2/GEM-K2AS KEYPAD EASY PROGRAM MENU

(Direct Entry)

Ent A1

#ZnXX

(Direct Entry)

Ent A2

#ZnXX

(Direct Entry)

Ent Fr

Zn#XX

(Direct Entry)

Ent2WF

Zn#XX

(Press YES or NO)

Report

all Zn

Y/N

(Direct Entry)

EntEE1

Zn#XX

(Direct Entry)

EntFol

Zn#XX

LNAPCO Security Systems XGEM-P9600 Programming Instructions

Page 7

WI 1185 6/03

24 Hour Zones in Area 1 (New Program Only)

•Enter the zone numbers of zones to be used as 24 Hour zones.

•Valid entries are from 01 to 96. Directly enter each zone number, including leading zeros.

•Press Uto save and repeat for any additional zone(s); press the NEXT/YES button to proceed.

NOTE: 24 Hour Zones will automatically be programmed as audible (Burg Output).

Chime Zones in Area 1 (New Program Only)

•Enter the zone numbers which are to be used as Chime Zones.

•Valid entries are from 01 to 96. Directly enter each zone number, including leading zeros.

•Press Uto save and then repeat for any additional zone(s), press the NEXT/YES button to proceed.

NOTE: A chime time of 2 seconds will be automatically programmed.

Chime 2 Zones in Area 1 (New Program Only)

•Enter the zone numbers which are to be used as Chime 2 Zones.

•Valid entries are from 01 to 96. Directly enter each zone number, including leading zeros.

•Press Uto save and then repeat for any additional zone(s), press the NEXT/YES button to proceed.

NOTE: A chime time of 2 seconds will be automatically programmed.

Chime 2 zones give a distinct pulsating tone when zone is faulted.

Exit/Entry2 Zones in Area 1 (New Program Only)

•Enter the zone numbers of zones to be used as Exit/Entry zones.

•Valid entries are from 01 to 96. Directly enter each zone number, including leading zeros.

•Press Uto save and repeat for any additional zone(s), press the NEXT/YES button to proceed.

NOTE: An Exit/Entry 2 Entry Time of 30 seconds will automatically be programmed.

50 mS Loop Response Zones (New Program Only)

•Enter the zone numbers of zones to have a 50mS loop response.

•Valid entries are from 01 to 08. Directly enter each zone number, including leading zeros.

•Press Uto save and then repeat for any additional zone(s), press the NEXT/YES button to proceed. Note: Only panel

zones 01-08 can be programmed for Quick Loop Response. All other zones can be programmed via their respective EZM's

(hardwire). Note: 750mS is required for Loop Response time in UL installations.

Aux Output Activated on Alarm Zones (New Program Only)

•Enter the zone numbers of zones to activate the Aux Output upon alarm.

•Valid entries are from 01 to 96. Directly enter each zone number, including leading zeros.

•Press Uto save and then repeat for any additional zone(s); press the NEXT/YES button to proceed.

NOTE: An Aux Output Timeout of 15 minutes will automatically be programmed.

Sensor Watch Zones (New Program Only)

•Enter the zone numbers of zones to be Sensor Watch zones.

•Valid entries are from 01 to 96. Directly enter each zone number, including leading zeros.

•Press Uto save and then repeat for any additional zone(s), press the NEXT/YES button to proceed.

NOTE: A Sensor Watch Time of 24 hours will automatically be programmed.

Keypad Sounder On Alarm Zones (New Program Only)

•Enter the zone numbers of all zones to activate the Keypad Sounder upon alarm.

•Valid entries are from 01 to 96. Directly enter each zone number, including leading zeros.

•Press Uto save and then repeat for any additional zone(s), press the NEXT/YES button to proceed.

Auto Bypass Re-entry Zones (New Program Only) (Not evaluated by UL)

•Enter the zone numbers of zones to be Auto Bypass Re-entry zones.

•Valid entries are from 01 to 96. Directly enter each zone number, including leading zeros.

•Press Uto save and then repeat for any additional zone(s), press the NEXT/YES button to proceed.

•Auto Bypass Re-entry Zones allow the system to be armed with the zone faulted but come back into the system (armed)

when the zone is subsequently closed.

(Direct Entry)

Ent24H

Zn#XX

(Direct Entry)

EntCZ1

Zn#XX

(Direct Entry)

EntCZ2

Zn#XX

(Direct Entry)

EntEE2

Zn#XX

(Direct Entry)

Ent50m

Zn#XX

(Direct Entry)

EntAux

Zn#XX

(Direct Entry)

Ent SW

Zn#XX

(Direct Entry)

EntKPS

Zn#XX

(Direct Entry)

EntAUB

Zn#XX

GEM-RP2ASE2/GEM-K2AS KEYPAD EASY PROGRAM MENU

XGEM-P9600 Programming Instructions LNAPCO Security Systems

!Page 8 WI 1185 6/03

Enable No EOLR Zones (New Program Only)

•Press YES to program all zones except 24 Hr & fire zones for No End Of Line Resistor. Press NO to continue.

•Do not program this feature for UL Installations.

Enable Telco Line Fault Test?

•Press YES to enable Telco Line Fault Test.

•Press NO to continue. NOTE: If enabled, a Telco Line Fault Test Delay of 60 sec. will automatically be programmed.

Enable Burg Output Chirp on KeyFob?

•Press the NEXT/YES button to enable Burg Output Chirp on KeyFob Arm / Disarm.

•Press the PRIOR/NO button to continue.

NOTE: The Burg Output will chirp once on Keyfob Arm and twice on Keyfob Disarm.

Enable SIA CP-01 Features?

•Press the NEXT/YES button to enable.

•Press the PRIOR/NO button to continue.

The SIA CP-01 Features are designed to reduce the incidence of false alarms. NOTE: Do not enable unless reporting,

otherwise system trouble Fail to Communicate may occur.

Number of Keypads in Area 1

•Enter the total number of Keypads to be installed in Area 1.

•Valid entries are from 01 to 15. Directly enter the number of keypads, including leading zeros.

Press Uto save. Press the NEXT/YES button to proceed.

Number of Keypads in Area 2

•Enter the total number of Keypads to be installed in Area 2.

•Valid entries are from 01 to 15. Directly enter the number of keypads, including leading zeros.

Press Uto save. Press the NEXT/YES button to proceed.

Central Station Receiver 1 Telephone Number

•Enter telephone number of up to 16 digits.

•Press 1through 9for digits 1–9; G0for a zero and 0for a blank (•).

•Press G1through G5for letters B–F, respectively.

•Pre-Dial Delay = “D” (G4); Dial-Tone Detection = “E” (G5).

•Press Uto save and press the NEXT/YES button to proceed.

NOTE: Central Station Receiver 2 and 3 Telephone Numbers must be entered in Direct Address Program-

ming. See CS Receiver Options.

(Press YES or NO)

EnNEOL

Y/N

(Press YES or NO)

Telco

Ln Flt

Y/N

(Press YES or NO)

KF Out

Chirp

Y/N

(Press YES or NO)

Enable

CP01?

Y/N

(Direct Entry)

Ent A1

#KP 01

(Direct Entry)

Ent A2

#KP 01

(Direct Entry)

Phone#

______

GEM-RP2ASE2/GEM-K2AS KEYPAD EASY PROGRAM MENU

LNAPCO Security Systems XGEM-P9600 Programming Instructions

Page 9

WI 1185 6/03

Central Station Receiver 1 Account Number

•Enter an account number of up to four digits.

•Press 0through 9for digits 0–9, and G0for a blank (•).

•Press Uto save and press the NEXT/YES button to proceed.

NOTE: Central Station Receiver 2 and 3 Account Numbers must be entered in Direct Address Programming. See

CS Reporting Options.

Central Station Receiver 1 Format

•From the table at the right enter the receiver format.

•Press 0through 9, and G0 for blank (•).

•Press G1 through G4 for letters B–E.

•Press Uto save and press the NEXT/YES button to proceed.

Easy Programming of Auto download ID #'s and PC Preset Callback Numbers (GEM-RP1CAe2 only)

For unattended PC Preset downloading, it is now possible to set the Auto download ID #’s and PC Preset Callback

from the Keypad Easy Program Mode.

•At the field for CENTRAL PHONE #, program an "F" followed by the Auto Download ID # (2 digits) and then the

Callback Telco # (up to 13 digits).

•Press Uto save.

•Exit Program Mode (CC).

•Enter Master Code

•Press R

•Go to Function "ACTIVATE DOWNLOAD Y/N" and press YES (P).

•The panel will automatically call the PC Preset computer and download the program on the specified Auto

Download line # of PC Preset.

Example: Program an Auto download ID # of 07 and a PC Preset Callback #

of 1-516-842-9400

•Go to Central Phone # input screen and press: [*] [5] [0] [7] [1] [5] [1] [6] [8] [4] [2] [9] [4] [0] [0] [ON/OFF]

CENTRAL PHONE #

F0715168429400

(Direct Entry)

Acc #

(____)

(Direct Entry)

RecFmt

( )

DATA

ENTRY

CS RECEIVER 1 FORMAT

blank(•) Ademco Slow, Silent Knight Slow

1 Sescoa, Vertex, DCI, Franklin

Fast

2 Radionics Fast

3 Silent Knight Fast

4 Radionics, DCI, Franklin Slow

5 Universal High Speed

8 Radionics BFSK

DATA

ENTRY

CS RECEIVER 1 FORMAT

9 FBI 4/3/1

0 Radionics Modem 2

B SIA

C Ademco Point ID

D Ademco Express

E Pager

NOTE: Modem IIe is available only in Direct

Address Programming. Central Station

Receiver 2 and 3 Formats can only be entered

in Direct Address Programming. See CS

Receiver Options.

GEM-RP2ASE2/GEM-K2AS KEYPAD EASY PROGRAM MENU

XGEM-P9600 Programming Instructions LNAPCO Security Systems

!Page 10 WI 1185 6/03

Enter User Codes (Press the Rbutton to set cursor.)

Enter up to 96 User Codes with User Options, Authority Level and Access Control Options

(if necessary) for each code. Refer to the tables below and on the next page for available

data entries for User Options, Authority Level and Access Control Options. Note: All 96

Users must be assigned to areas in “Enable User Code by Area” (Address 2500-2595) in

Direct Address Programming. By default, only User 1 is enabled in Area 1 and Area 2.

User 2 - 8 are enabled in Area 1 and user 9 - 16 are enabled in Area 2.

!Press the Rbutton to set the cursor to the User Code. Use the number buttons

1through 9to enter a code from 3 to 6 digits. Enter up to 6 digits in the first six

boxes from left to right for each user code. Valid entries are: 0-9. Note: Press the 0

button for a zero. No blank spaces in between; leave blank (•) any trailing boxes. If an

“Ambush Code” (Address 0495) is entered, do not program the first two digits of ANY User

Code as the same digits entered for the “Ambush Code”.

!If the programmed code is less than 6 digits, press the Rbutton to set the cursor to the OPTION/LEVEL.

!Refer to the tables below for the available User Option and User Level data entries. Enter the user options data in

the left digit. Enter the level data (with arming options, if any, added) in the right digit. Note: For entries greater than

9, press the G1 buttons through the G5 buttons for B through F, respectively.

!For Keypad Access Control, press the Rbutton once again to program applicable keypads. Refer to the tables

below, use the number buttons to enter the data for Keypad 1–4 in the right digit; and the data for Keypad 5–8 data

in the left digit. (Press the 0buttons for blank).

USER OPTIONS

USER CODE

(UP TO 6 DIGITS)

USER

OPTION

USER

LEVEL

ACCESS CONTROL

KEYPADS

DATA

ENTRIES

AUTHORITY

LEVEL

CODE

TYPE

blank (•) NONE ARM/DISARM

1 LEVEL 1 ARM/DISARM

2 LEVEL 2 ARM/DISARM

3 LEVEL 3 ARM/DISARM

4 NONE ARM ONLY

5 LEVEL 1 ARM ONLY

6 LEVEL 2 ARM ONLY

7 LEVEL 3 ARM ONLY

8 NONE SERVICE

9 LEVEL 1 SERVICE

0 LEVEL 2 SERVICE

B LEVEL 3 SERVICE

Note: “Y” indicates option is enabled.

USER OPTIONS

DATA

ENTRIES

BLOCKED

VIEW

USER

PROGRAM

BYPASS OVERVIEW

blank (•)

1 Y

2 Y

3 Y Y

4 Y

5 Y Y

6 Y Y

7 Y Y Y

8 Y

9 Y Y

0 Y Y

B Y Y Y

C Y Y

D Y Y Y

E Y Y Y

F Y Y Y Y

DISABLED

Note: “Y” indicates option is enabled.

ACCESS CONTROL KEYPADS

DATA

ENTRIES

K.P. 1 K.P. 2 K.P. 3 K.P. 4

blank (•)

1 Y

2 Y

3 Y Y

4 Y

5 Y Y

6 Y Y

7 Y Y Y

8 Y

9 Y Y

0 Y Y

B Y Y Y

C Y Y

D Y Y Y

E Y Y Y

F Y Y Y Y

NONE

Example: Enter a code of “123456” as

“123456” (from left to right).

Note: “Y” indicates option is enabled.

ACCESS CONTROL KEYPADS

DATA

ENTRIES

K.P. 5 K.P. 6 K.P. 7 K.P. 8

blank (•)

1 Y

2 Y

3 Y Y

4 Y

5 Y Y

6 Y Y

7 Y Y Y

8 Y

9 Y Y

0 Y Y

B Y Y Y

C Y Y

D Y Y Y

E Y Y Y

F Y Y Y Y

NONE

(Direct Entry)

User01

______

(Direct Entry)

OPT__

(Direct Entry)

ACC __

GEM-RP2ASE2/GEM-K2AS KEYPAD EASY PROGRAM MENU

LNAPCO Security Systems XGEM-P9600 Programming Instructions

Page 11

WI 1185 6/03

Example: Program a code of “2222” for user 02, with User Option of “User Program”, User “Level 3” and Access Control Option

“Keypad No. 1”. Enter “2222” for a user code, “2 3” for user option and “blank(•) 1” for access control option.

CHANGING OR CANCELING A CODE: To change any code, merely program over the existing code as described

above and press Uto save. Similarly, to cancel a code, blank out each number of the code and press Uto save to

save.

USER AUTHORITY LEVEL

FUNCTION LEVEL*

DISPLAY ZN FAULTS 1

DISPLAY ZN BYPASSED 1

DISPLAY ZN DIRECTORY 1

ACTIVATE BELL TEST 1

DISPLAY PHONE #’S 1

DISPLAY SYS TRBL 1

DISPLAY FIRE ALARM 1

DISPLAY FIRE TRBL 1

DISPLAY OP/CL 3

ACTIVATE OVERVIEW 3**

ACTIVATE CHIME 1

ACTIVATE WATCH 2

RESET SYSTEM TRBL 3

RESET SENSOR MSG 3

START EXIT TIME 1

FAULT FIND ***

ACTIVATE LOCATE ***

EZM ZONE FIND ***

ACTIVATE DIALER TEST 3

DISPLAY ALARM LOG 3

DISPLAY TOTAL LOG 3

DISPLAY FIRE LOG 3

DISPLAY OP/CL LOG 3

DISPLAY SYSTEM LOG 3

AUTOARM IN 1-4HRS 2

DISPLAY AUTOARM SCHD 3

ACTIVATE PROGRAM 3**

ACTIVATE DOWNLOAD 3

DISPLY RF XMITTER STAT 1

RELAY CONTROL 1

KEYPAD DISPLAY FUNCTION MENU NOTES:

* Minimum Level required to access function

** Level-3 Code with appropriate user option

*** Requires Dealer Code

Related User Options: “Ambush Code” (Address 0495), “Panel Access Code” (Address

0490), “Dealer Security Code” (Address 0500) & “Enable User Code by Area” (Address

2500-2595).

OPTIONS EXPLANATION

Disabled User Code not active in this area.

Blocked View Allows User Code to block another code from being viewed by another user.

An unblocked code cannot view a blocked code, but a blocked code can

view all codes. The master user code and the dealer program code can view

all codes.

User Program User Program Option is enabled for Keypad 1 only, wherever it is connected

(any area). If enabled, Level 3 must also be enabled.

Bypass Allows User Code to bypass zones.

Overview This option, along with Level 3 Authorization, enables selection of

OVERVIEW mode at a keypad. This Mode provides a system status display

of all areas at a glance.

Arm Only Prevents User Code from disarming this area.

Service A Service Code has restricted arm/disarm rights; if an area is armed with a

Service Code, a “SERVICE ON” appears on the GEM-RP2ASe2 keypad (a “S”

on the GEM-RP1CAe2 keypad) and the area can be disarmed with any valid

User Code, including a Service Code. If the area is armed with OTHER than

a Service Code, it CANNOT be disarmed with a Service Code. This is

typically used to allow tradesmen access to premises under control of the

owner.

Access This is normally used to activate a door striker while an area is disarmed. A

code with the access option will not function as an arm/disarm code. When

the code is entered, the keypad will display “ENTER NOW” and the Brown

Wire on the keypad will become Active Low (Ground Potential) for 7

seconds.

USER OPTIONS

Ambush Allows User Code to send Ambush signal to Central Station.

GEM-RP2ASE2/GEM-K2AS KEYPAD EASY PROGRAM MENU

XGEM-P9600 Programming Instructions LNAPCO Security Systems

!Page 12 WI 1185 6/03

RF Transmitter Points (Press Rto set cursor.)

For each transmitter enter: (For wireless systems only. Also see Quick Method, which follows)

•The zone number (01–96) to which the transmitter will be mapped.

•The 6-digit RF ID # and 1-digit checksum number printed on the transmitter and box,

•The point number (1–2); enter “9” for unsupervised (all points).

•Press Uto save and NEXT/YES button to proceed when all transmitters have been entered.

NOTE: When programming the ID Code number, “0” through ”9” = 0through 9; A = G0 ;

B = G1 ; C = G2 ; D = G3 ; E = G4 and “F” =

G5.

Quick Method. If a receiver is already installed in the panel, transmitter wireless points can be pro-

grammed automatically (“enrolled”) using the following procedure. NOTE: The transmitter point will be en-

rolled only if the signal strength is 3 or greater.

1. Enter the zone number to which the transmitter point will be mapped.

2. Press Bto enter the Enroll Mode. The red and green LEDs on the keypad will flash and the window will

display as shown at left.

3. Open the loop of the point that is to be programmed (GEM-TRANS2 only).

4. Install the transmitter battery. The keypad will beep to indicate that the point has been successfully enrolled.

Multi-point transmitters can be mapped to successive zones simultaneously.

Key Fob Transmitters as Arm/Disarm & Control Devices (Press Rto set cursor).

Key fobs can be programmed as “Arm/Disarm” devices using their On/Off buttons (refer to WI752). For each

Key Fob Transmitter, enter:

•The Key Fob Transmitter number (01–16).

•The area number to which transmitter is assigned (0 to disable keyfob, 1 or 2).

•The 6-digit RF ID # and 1-digit checksum number printed on the transmitter and box,

•The Aux 1 Option (see key fob aux 1 & aux 2 options).

•The Aux 2 Option (see key fob aux 1 & aux 2 options).

•Press Uto save and NEXT/YES button to proceed when all key fobs have been entered.

NOTE: When programming the ID Code number, “0” through ”9” = 0through 9; A = G0 ;

B = G1 ;

C = G2 ; D = G3 ; E = G4 and “F” = G5.

ZN# XMIT#+CS P

Zn01- 000000:0-0

ZN# XMIT#+CS P

ZN01- ENROLL:A--

Example. A 2-point transmitter has the RF ID number 287613:1. Map point

1 to Zone 6 and point 2 to Zone 9.

1. Enter the Enroll mode as described above.

2. Enter Zone “06”.

3. Open point-1 loop.

4. Install the battery. The keypad will beep once to indicate that one point

has been programmed. (Transmitter 287613:1, point 1 will be mapped

to Zone 6).

5. Enter Zone “09”.

6. Close point-1 loop and open point-2 loop.

7. Remove the transmitter battery, then re-install it. The keypad will beep

once to indicate that one point has been programmed. (Transmitter

287613:1, point 2 is mapped to Zone 9).

KEY FOB ZONE ASSIGNMENT: Key fobs can also be assigned to zones to allow multiple wireless panic buttons on one alarm

system, each reporting to a central station, a pager or having a description on the keypad that describes the person holding the key

fob, the location where the person holding the key fob is stationed, or the special purpose of the key fob button being depressed.

See the next page on Key Fob Transmitters as Zone Input Devices .

(Direct Entry)

Zn# 01

000000

(Direct Entry)

:0 Pt

(Direct Entry)

KFob01

Area

(Direct Entry)

000000

(Direct Entry)

:0 0 0

GEM-RP2ASE2/GEM-K2AS KEYPAD EASY PROGRAM MENU

LNAPCO Security Systems XGEM-P9600 Programming Instructions

Page 13

WI 1185 6/03

Key Fob Transmitters as Zone Input Devices

(Refer to display above: press the PRIOR button to go backwards).

Each of the 4 key fob buttons can be assigned to a zone. For example, On button = point 1; Off button = point

2; A1 = point 3; A2 = point 4. Up to 96 key fobs (using 1 button) or 48 key fobs (using 2 buttons) or 28 key fobs

(using all 4 buttons) or any combination up to a maximum of 96 controlled zones can be assigned, providing

multiple wireless panic buttons on a system, each reporting to a Central Station or a pager and/or annunciating

on a keypad the key fob zone number with a description. To assign a key fob to a zone: program the key fob

as you would a transmitter, entering the key fob's ID code, check sum and point number at the appropriate

zone. The “Quick Method” is not allowed. The zone may be hardwired to an electrical sensor as well as as-

signed to a key fob (either one will activate the zone alarm output). NOTE: If assigning a key fob to a zone, the

“ON/OFF” buttons on the key fob will no longer arm/disarm the system. The key fob is converted to a “panic

only” device.

Enter Date (Press Rto set cursor).

•Enter the current date in the format MM/DD/YY. (MM = month, DD = day and YY = year.

•Press Uto save. Press the NEXT/YES button to proceed.

Enter Time (Press Rto set cursor.)

•Enter the current time in format HH:MMA/P, where HH=hours (01–12); MM=minutes (00–59).

•Select AM or PM by pressing any number button.

•Press Uto save. Press the NEXT/YES button to proceed.

Dealer Code

•Directly enter the Dealer Code (default = 456789), using 0through 9buttons.

•Press Uto save.

•Re-enter the Dealer Code to verify the previous code.

•Press Uto save.

•Press the NEXT/YES button to proceed.

(Direct Entry)

Enter Date

( / / )

(Direct Entry)

Enter Time

( : )

Dealer Code

456789

DEALER CODE

RE-ENTER

CLEAR PROGRAM: Should it be necessary to create a new custom default program, (a) from the Dealer Program Mode, press Cto enter

the Address Program Mode; (b) access Location 4091 (Clear Program) or 1093 (Cold Start); (c) press Uand then (d) press Cto exit the

Dealer Program Mode. A “SYSTEM TROUBLE/E09-00 SERVICE” will occur. Press Cto silence the keypad.

Clear Dealer Program (Erases Dealer Program)

Use this feature to erase the Panel Program, while maintaining Scheduled Data and Zone Descriptions. Access

address 4091 and press U. Data entry is not allowed. NOTE: Enter Easy Menu Driven Program Mode

to reprogram system.

Cold Start (Erases Entire Program)

This erases all programmed data (Dealer Program, Zone Description Data and Schedules). Access ad-

dress 4093 and press U. Data entry is not allowed. NOTE: Some features (schedules) can only be pro-

grammed again with the Downloading Software.

EXIT DEALER PROGRAM MODE: This completes the custom default program. Press Cto enter the Direct Address Program

Mode for further programming or press Conce again to end all programming and resume normal keypad operation.

4091 XX H

4093 XX H

DATA

ENTRY

AUX 1/AUX 2 OPTIONS

0 None

1 Relay Group 1 Toggle

2 Relay Group 2 Toggle

3 Relay Group 3 Toggle

4 Relay Group 4 Toggle

5 Relay Group 5 Toggle

6 Relay Group 6 Toggle

7 Relay Group 7 Toggle

8 Relay Group 8 Toggle

9 Panic

A Auxiliary

B Instant

C Aux. Output Toggle

D Access on Aux. Output

E Arm STAY

F Interior Bypass

ZONE DESCRIPTIONS: GEM-RP2ASe2/GEM-K2AS cannot be used to enter Zone Descriptions. To enter Zone Descriptions, you

must use the GEM-RP1CAe2/GEM-K1CA Keypad (See WI777) or the PCD-Windows Quickloader Software.

GEM-RP2ASE2/GEM-K2AS KEYPAD EASY PROGRAM MENU

XGEM-P9600 Programming Instructions LNAPCO Security Systems

!Page 14 WI 1185 6/03

GEM-RP3DGTL/GEM-K3DGTL and GEM-RP4RFC/GEM-K4RF Keypad Easy Program Menu

To enter Dealer Program Mode, see page 5. Once entered, press R, followed by [PRIOR/NO] repeatedly until “17” is displayed (scroll back

by pressing B). Press [NEXT] to enter Easy Program Mode. For the GEM-RP3DGTL/GEM-K3DGTL (and GEM-RP4RFC/GEM-K4RF),

questions are in the form of a 2-digit number flashing in the display. Press Rto set the cursor into the next field to answer the question.

Press Ragain to scroll through each segment. Press [NEXT] to go to the next question. To review your Easy Program Mode responses

(before pressing Uto save), press Runtil the 2-digit question number flashes in the display again. If the data is correct, press Uto save.

If the data is incorrect, press Rto set the cursor into the next field and again enter your data. Note: Review your Easy Program Mode re-

sponses after the initial programming of the control, except for questions marked "For New Panel Only". These questions set up the basic struc-

ture of the panel program ("Number of Zones in an Area", etc.) and cannot be viewed or altered once set. To exit Dealer Program Mode, press

Ctwice. To return the panel to the factory default, enter the Direct Address Program Mode, go to location 1198 and press U.

Total Number of Zones in Area 1 (New Program Only)

•Enter the total number of zones to be programmed for Area 1.

•Valid entries are from 01 to 96. Directly enter the total number of zones, including leading zeros.

•The system is based on groups of 4 zones each (after the first 8 zones), and will automatically round up to

the next group of 4. For example, if you enter 18, it will automatically convert this to 20 zones. Press Uto

save. Press the NEXT/YES button to proceed.

Total Number of Zones in Area 2 (New Program Only)

•Programming Area 2 is identical to Area 1 above.

Press the NEXT/YES button to proceed.

Fire Zones in Area 1 (New Program Only)

•Enter the zone number of any Fire Zones (including 2-wire, 4-wire or wireless).

•Valid entries are from 01 to 96.

•Directly enter each zone number, including leading zeros, and press Uto save, and then repeat for any

additional zone(s). Press the NEXT/YES button to proceed.

2-Wire Fire Zones in Area 1 (New Program Only)

•Enter the zone number of any Fire Zone (from previous question) to be used with 2-wire smoke detectors.

•Valid entries are 07 and 08. Directly enter each zone number, including leading zeros.

•Press Uto save, and repeat for any additional zone(s); press NEXT to proceed.

NOTE: Only zones which have been designated as Fire Zones can be programmed as 2 Wire Fire zones.

JP3 must be set to “2-WF” position for 2-wire fire. (refer to Installation Instructions).

Local or Central Station Reporting System (New Program Only)

Press the NEXT/YES button for all zones to report; press the PRIOR/NO button for local system.

Exit/Entry Zones in Area 1 (New Program Only)

•Enter the zone numbers of zones to be used as Exit/Entry zones.

•Valid entries are from 01 to 96. Directly enter each zone number, including leading zeros.

•Press Uto save and repeat for any additional zone(s); press the NEXT/YES button to proceed.

NOTE: Exit/Entry Entry time of 30 seconds will automatically be programmed.

(Direct Entry)

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

(Direct Entry)

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

(Direct Entry)

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

(Direct Entry)

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

Flashing

GEM-RP3DGTL/GEM-K3DGTL AND GEM-RP4RFC/GEM-K4RF KEYPAD EASY PROGRAM MENU

(Direct Entry)

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

(Direct Entry)

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

LNAPCO Security Systems XGEM-P9600 Programming Instructions

Page 15

WI 1185 6/03

Interior Zones in Area 1 (New Program Only)

•Enter the zone numbers to be used as Interior Zones.

•Valid entries are from 01 to 96. Directly enter each zone number, including leading zeros.

•Press Uto save and then repeat for any additional zone(s).

•Press the NEXT/YES button to proceed.

•All Interior zones will also be automatically programmed as “Exit/Entry Follower” and as "Power Up Delay" zones.

24 Hour Zones in Area 1 (New Program Only)

•Enter the zone numbers of zones to be used as 24 Hour zones.

•Valid entries are from 01 to 96. Directly enter each zone number, including leading zeros.

•Press Uto save and repeat for any additional zone(s); press the NEXT/YES button to proceed.

NOTE: 24 Hour Zones will automatically be programmed as audible (Burg Output).

Chime Zones in Area 1 (New Program Only)

•Enter the zone numbers which are to be used as Chime Zones.

•Valid entries are from 01 to 96. Directly enter each zone number, including leading zeros.

•Press Uto save and then repeat for any additional zone(s), press the NEXT/YES button to proceed.

NOTE: A chime time of 2 seconds will be automatically programmed.

Chime 2 Zones in Area 1 (New Program Only)

•Enter the zone numbers which are to be used as Chime 2 Zones.

•Valid entries are from 01 to 96. Directly enter each zone number, including leading zeros.

•Press Uto save and then repeat for any additional zone(s), Press the NEXT/YES button to proceed.

NOTE: A chime time of 2 seconds will be automatically programmed.

Chime 2 zones give a distinct pulsating tone when zone is faulted.

Exit/Entry2 Zones in Area 1 (New Program Only)

•Enter the zone numbers of zones to be used as Exit/Entry zones.

•Valid entries are from 01 to 96. Directly enter each zone number, including leading zeros.

•Press Uto save and repeat for any additional zone(s); press the NEXT/YES button to proceed.

NOTE: An Exit/Entry 2 Entry Time of 30 seconds will automatically be programmed.

50 mS Loop Response Zones (New Program Only)

•Enter the zone numbers of zones to be have a 50mS loop response.

•Valid entries are from 01 to 08. Directly enter each zone number, including leading zeros.

•Press Uto save and then repeat for any additional zone(s), Press the NEXT/YES button to proceed. Note: Only

panel zones 01-08 can be programmed for Quick Loop Response. All other zones can be programmed via their re-

spective EZM's (hardwire). Note: 750mS is required for Loop Response time in UL installations.

Aux Output Activated on Alarm Zones (New Program Only)

•Enter the zone numbers of zones to activate the PGM2 upon alarm.

•Valid entries are from 01 to 96. Directly enter each zone number, including leading zeros.

•Press Uto save and then repeat for any additional zone(s), Press the NEXT/YES button to proceed.

NOTE: A PGM2 Timeout of 15 minutes will automatically be programmed.

Sensor Watch Zones (New Program Only)

•Enter the zone numbers of zones to be Sensor Watch zones.

•Valid entries are from 01 to 96. Directly enter each zone number, including leading zeros.

•Press Uto save and then repeat for any additional zone(s), Press the NEXT/YES button to proceed.

NOTE: A Sensor Watch Time of 24 hours will automatically be programmed.

(Direct Entry)

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

(Direct Entry)

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

(Direct Entry)

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

(Direct Entry)

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

(Direct Entry)

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

(Direct Entry)

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

(Direct Entry)

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

GEM-RP3DGTL/GEM-K3DGTL AND GEM-RP4RFC/GEM-K4RF KEYPAD EASY PROGRAM MENU

XGEM-P9600 Programming Instructions LNAPCO Security Systems

!Page 16 WI 1185 6/03

Keypad Sounder On Alarm Zones (New Program Only)

•Enter the zone numbers of all zones to activate the Keypad Sounder upon alarm.

•Valid entries are from 01 to 96. Directly enter each zone number, including leading zeros.

•Press Uto save and then repeat for any additional zone(s), Press the NEXT/YES button to proceed.

Auto Bypass Re-entry Zones (New Program Only) (Not evaluated by UL)

•Enter the zone numbers of zones to be Auto Bypass Re-entry zones.

•Valid entries are from 01 to 96. Directly enter each zone number, including leading zeros.

•Press Uto save and then repeat for any additional zone(s), Press the NEXT/YES button to proceed.

•Auto Bypass Re-entry Zones allow the system to be armed with the zone faulted but come back into the system

(armed) when the zone is subsequently closed.

Enable No EOLR Zones (New Program Only)

•Press YES to program all zones except 24 Hr & fire zones for No End Of Line Resistor. Press NO to continue.

•Do not program this feature for UL Installations.

Enable Telco Line Fault Test?

•Press YES to enable Telco Line Fault Test.

•Press NO to continue. NOTE: If enabled, a Telco Line Fault Test Delay of 60 sec. will automatically be pro-

grammed.

Enable Burg Output Chirp on KeyFob?

•Press the NEXT/YES button to enable Burg Output Chirp on KeyFob Arm / Disarm.

•Press the PRIOR/NO button to continue.

NOTE: The Burg Output will chirp once on Keyfob Arm and twice on Keyfob Disarm.

Enable SIA CP-01 Features?

•Press the NEXT/YES button to enable.

•Press the PRIOR/NO button to continue.

The SIA CP-01 Features are designed to reduce the incidence of false alarms. NOTE: Do not enable unless

reporting, otherwise system trouble Fail to Communicate may occur.

Number of Keypads in Area 1

•Enter the total number of Keypads to be installed in Area 1.

•Valid entries are from 01 to 15. Directly enter the number of keypads, including leading zeros.

Press Uto save. Press the NEXT/YES button to proceed.

Number of Keypads in Area 2

•Enter the total number of Keypads to be installed in Area 2.

•Valid entries are from 01 to 15. Directly enter the number of keypads, including leading zeros.

Press Uto save. Press the NEXT/YES button to proceed.

(Direct Entry)

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

(Direct Entry)

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

(Press YES or NO)

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

(Press YES or NO)

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

(Press YES or NO)

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

(Press YES or NO)

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

(Direct Entry)

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

_ H

(Direct Entry)

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

_ H

GEM-RP3DGTL/GEM-K3DGTL AND GEM-RP4RFC/GEM-K4RF KEYPAD EASY PROGRAM MENU

LNAPCO Security Systems XGEM-P9600 Programming Instructions

Page 17

WI 1185 6/03

Central Station Receiver 1 Telephone Number

•Enter telephone number of up to 16 digits.

•Press 1through 9for digits 1–9; G0for a zero and 0for a blank (•).

•Press G1through G5for letters B–F, respectively.

•Pre-Dial Delay = “D” (G4); Dial-Tone Detection = “E” (G5).

•Press Uto save and press the NEXT/YES button to proceed.

NOTE: Central Station Receiver 2 and 3 Telephone Numbers must be entered in Direct Address Program-

ming. See CS Receiver Options.

Central Station Receiver 1 Account Number

•Enter an account number of up to four digits.

•Press 0through 9for digits 0–9, and G0for a blank (•).

•Press Uto save and press the NEXT/YES button to proceed.

NOTE: Central Station Receiver 2 and 3 Account Numbers must be entered in Direct Address Program-

ming. See CS Reporting Options.

Central Station Receiver 1 Format

•From the table at the right enter the receiver format.

•Press 0through 9, and G0 for blank (•).

•Press G1 through G4 for letters B–E.

•Press Uto save and press the NEXT/YES button to proceed.

DATA

ENTRY

CS RECEIVER 1 FORMAT

blank(•) Ademco Slow, Silent Knight Slow

1 Sescoa, Vertex, DCI, Franklin

Fast

2 Radionics Fast

3 Silent Knight Fast

4 Radionics, DCI, Franklin Slow

5 Universal High Speed

8 Radionics BFSK

DATA

ENTRY

CS RECEIVER 1 FORMAT

9 FBI 4/3/1

0 Radionics Modem 2

B SIA

C Ademco Point ID

D Ademco Express

E Pager

NOTE: Modem IIe is available only in Direct

Address Programming. Central Station

Receiver 2 and 3 Formats can only be entered

in Direct Address Programming. See CS

Receiver Options.

(Direct Entry)

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

_ 3

(Direct Entry)

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

GEM-RP3DGTL/GEM-K3DGTL AND GEM-RP4RFC/GEM-K4RF KEYPAD EASY PROGRAM MENU

(Direct Entry)

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

_ 3

XGEM-P9600 Programming Instructions LNAPCO Security Systems

!Page 18 WI 1185 6/03

Enter User Codes (Press the Rbutton to set cursor.)

Enter up to 96 User Codes with User Options, Authority Level and Access Control

Options (if necessary) for each code. Refer to the tables below and on the next page

for available data entries for User Options, Authority Level and Access Control

Options. Note: All 96 Users must be assigned to areas in “Enable User Code by

Area” (Address 2500-2595) in Direct Address Programming. By default, only User 1

is enabled in Area 1 and Area 2.

User 2 - 8 are enabled in Area 1 and user 9 - 16 are enabled in Area 2.

!Press the Rbutton to set the cursor to the User Code. Use the number

buttons 1through 9to enter a code from 3 to 6 digits. Enter up to 6 digits

(4 digits is recommended) in the first six boxes from left to right for each user code.

Valid entries are: 0-9. Note: Press the 0button for a zero. No blank spaces in between; leave blank (•) any trailing

boxes. If an “Ambush Code” (Address 0495) is entered, do not program the first two digits of ANY User Code as the

same digits entered for the “Ambush Code”.

!If the programmed code is less than 6 digits, press the Rbutton to set the cursor to the OPTION/LEVEL.

!Refer to the tables below for the available User Option and User Level data entries. Enter the user options data in

the left digit. Enter the level data (with arming options, if any, added) in the right digit. Note: For entries greater than 9,

press the G1 buttons through the G5 buttons for B through F, respectively.

!For Keypad Access Control, press the Rbutton once again to program applicable keypads. Refer to the tables

below, use the number buttons to enter the data for Keypad 1–4 in the right digit; and the data for Keypad 5–8 data in

the left digit. (Press the 0buttons for blank).

USER OPTIONS

USER CODE

(UP TO 6 DIGITS)

USER

OPTION

USER

LEVEL

ACCESS CONTROL

KEYPADS

DATA

ENTRIES

AUTHORITY

LEVEL

CODE

TYPE

blank (•) NONE ARM/DISARM

1 LEVEL 1 ARM/DISARM

2 LEVEL 2 ARM/DISARM

3 LEVEL 3 ARM/DISARM

4 NONE ARM ONLY

5 LEVEL 1 ARM ONLY

6 LEVEL 2 ARM ONLY

7 LEVEL 3 ARM ONLY

8 NONE SERVICE

9 LEVEL 1 SERVICE

0 LEVEL 2 SERVICE

B LEVEL 3 SERVICE

Note: “Y” indicates option is enabled.

USER OPTIONS

DATA

ENTRIES

BLOCKED

VIEW

USER

PROGRAM

BYPASS OVERVIEW

blank (•)

1 Y

2 Y

3 Y Y

4 Y

5 Y Y

6 Y Y

7 Y Y Y

8 Y

9 Y Y

0 Y Y

B Y Y Y

C Y Y

D Y Y Y

E Y Y Y

F Y Y Y Y

DISABLED

Note: “Y” indicates option is enabled.

ACCESS CONTROL KEYPADS

DATA

ENTRIES

K.P. 1 K.P. 2 K.P. 3 K.P. 4

blank (•)

1 Y

2 Y

3 Y Y

4 Y

5 Y Y

6 Y Y

7 Y Y Y

8 Y

9 Y Y

0 Y Y

B Y Y Y

C Y Y

D Y Y Y

E Y Y Y

F Y Y Y Y

NONE

Example: Enter a code of “123456” as

“123456” (from left to right).

Note: “Y” indicates option is enabled.

ACCESS CONTROL KEYPADS

DATA

ENTRIES

K.P. 5 K.P. 6 K.P. 7 K.P. 8

blank (•)

1 Y

2 Y

3 Y Y

4 Y

5 Y Y

6 Y Y

7 Y Y Y

8 Y

9 Y Y

0 Y Y

B Y Y Y

C Y Y

D Y Y Y

E Y Y Y

F Y Y Y Y

NONE

(Direct Entry)

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

GEM-RP3DGTL/GEM-K3DGTL AND GEM-RP4RFC/GEM-K4RF KEYPAD EASY PROGRAM MENU

LNAPCO Security Systems XGEM-P9600 Programming Instructions

Page 19

WI 1185 6/03

Example: Program a code of “2222” for user 02, with User Option of “User Program”, User “Level 3” and Access Control Option

“Keypad No. 1”. Enter “2222” for a user code, “2 3” for user option and “blank(•) 1” for access control option.

CHANGING OR CANCELING A CODE: To change any code, merely program over the existing code as described

above and press Uto save. Similarly, to cancel a code, blank out each number of the code and press Uto save to

save.

USER AUTHORITY LEVEL

FUNCTION LEVEL*

DISPLAY ZN FAULTS 1

DISPLAY ZN BYPASSED 1

DISPLAY ZN DIRECTORY 1

ACTIVATE BELL TEST 1

DISPLAY PHONE #’S 1

DISPLAY SYS TRBL 1

DISPLAY FIRE ALARM 1

DISPLAY FIRE TRBL 1

DISPLAY OP/CL 3

ACTIVATE OVERVIEW 3**

ACTIVATE CHIME 1

ACTIVATE WATCH 2

RESET SYSTEM TRBL 3

RESET SENSOR MSG 3

START EXIT TIME 1

FAULT FIND ***

ACTIVATE LOCATE ***

EZM ZONE FIND ***

ACTIVATE DIALER TEST 3

DISPLAY ALARM LOG 3

DISPLAY TOTAL LOG 3

DISPLAY FIRE LOG 3

DISPLAY OP/CL LOG 3

DISPLAY SYSTEM LOG 3

AUTOARM IN 1-4HRS 2

DISPLAY AUTOARM SCHD 3

ACTIVATE PROGRAM 3**

ACTIVATE DOWNLOAD 3

DISPLY RF XMITTER STAT 1

RELAY CONTROL 1

KEYPAD DISPLAY FUNCTION MENU NOTES:

* Minimum Level required to access function

** Level-3 Code with appropriate user option

*** Requires Dealer Code

Related User Options: “Ambush Code” (Address 0495), “Panel Access Code” (Address

0490), “Dealer Security Code” (Address 0500) & “Enable User Code by Area” (Address

2500-2595).

OPTIONS EXPLANATION

Disabled User Code not active in this area.

Blocked View Allows User Code to block another code from being viewed by another user.

An unblocked code cannot view a blocked code, but a blocked code can

view all codes. The master user code and the dealer program code can view

all codes.

User Program User Program Option is enabled for Keypad 1 only, wherever it is connected

(any area). If enabled, Level 3 must also be enabled.

Bypass Allows User Code to bypass zones.

Overview This option, along with Level 3 Authorization, enables selection of

OVERVIEW mode at a keypad. This Mode provides a system status display

of all areas at a glance.

Arm Only Prevents User Code from disarming this area.

Service A Service Code has restricted arm/disarm rights; if an area is armed with a

Service Code, a “SERVICE ON” appears on the GEM-RP2ASe2 keypad (a “S”

on the GEM-RP1CAe2 keypad) and the area can be disarmed with any valid

User Code, including a Service Code. If the area is armed with OTHER than

a Service Code, it CANNOT be disarmed with a Service Code. This is

typically used to allow tradesmen access to premises under control of the

owner.

Access This is normally used to activate a door striker while an area is disarmed. A

code with the access option will not function as an arm/disarm code. When

the code is entered, the keypad will display “ENTER NOW” and the Brown

Wire on the keypad will become Active Low (Ground Potential) for 7

seconds.

USER OPTIONS

Ambush Allows User Code to send Ambush signal to Central Station.

GEM-RP3DGTL/GEM-K3DGTL AND GEM-RP4RFC/GEM-K4RF KEYPAD EASY PROGRAM MENU

XGEM-P9600 Programming Instructions LNAPCO Security Systems

!Page 20 WI 1185 6/03

RF Transmitter Points (Press Rto set cursor.)

For each transmitter enter: (For wireless systems only. Also see Quick Method, which follows)

•The zone number (01–96) to which the transmitter will be mapped.

•The 6-digit RF ID # and 1-digit checksum number printed on the transmitter and box,

•The point number (1–2); enter “9” for unsupervised (all points).

•Press Uto save and NEXT/YES button to proceed when all transmitters have been entered.

NOTE: When programming the ID Code number, “0” through ”9” = 0through 9; A =

G0 ; B = G1 ; C = G2 ; D = G3 ; E = G4 and “F” = G5.

Quick Method. If a receiver is already installed in the panel, transmitter wireless points can be programmed automatically (“enrolled”) using the

following procedure. NOTE: The transmitter point will be enrolled only if the signal strength is 3 or greater.

1. Enter the zone number to which the transmitter point will be mapped.

2. Press Bto enter the Enroll Mode. The red and green LEDs on the keypad will flash and the window will

display as shown at left.

3. Open the loop of the point that is to be programmed (GEM-TRANS2 only).

4. Install the transmitter battery. The keypad will beep to indicate that the point has been successfully enrolled.

Multi-point transmitters can be mapped to successive zones simultaneously.

Key Fob Transmitters as Arm/Disarm & Control Devices (Press Rto set cursor).

Key fobs can be programmed as “Arm/Disarm” devices using their On/Off buttons (refer to WI752).

For each Key Fob Transmitter, enter:

•The Key Fob Transmitter number (01–16).

•The area number to which transmitter is assigned (0 to disable keyfob, 1 or 2).

•The 6-digit RF ID # and 1-digit checksum number printed on the transmitter and box,

•The Aux 1 Option (see key fob aux 1 & aux 2 options).

•The Aux 2 Option (see key fob aux 1 & aux 2 options).

•Press Uto save and NEXT/YES button to proceed when all key fobs have been entered.

NOTE: When programming the ID Code number, “0” through ”9” = 0through 9; A = G0 ; B = G1 ;

C = G2 ; D = G3 ; E = G4 and “F” = G5.

ZN# XMIT#+CS P

Zn01- 000000:0-0

ZN# XMIT#+CS P

ZN01- ENROLL:A--

Example. A 2-point transmitter has the RF ID number 287613:1. Map point

1 to Zone 6 and point 2 to Zone 9.

1. Enter the Enroll mode as described above.

2. Enter Zone “06”.

3. Open point-1 loop.

4. Install the battery. The keypad will beep once to indicate that one point

has been programmed. (Transmitter 287613:1, point 1 will be mapped

to Zone 6).

5. Enter Zone “09”.

6. Close point-1 loop and open point-2 loop.

7. Remove the transmitter battery, then re-install it. The keypad will beep

once to indicate that one point has been programmed. (Transmitter

287613:1, point 2 is mapped to Zone 9).

KEY FOB ZONE ASSIGNMENT: Key fobs can also be assigned to zones to allow multiple wireless panic buttons on one alarm

system, each reporting to a central station, a pager or having a description on the keypad that describes the person holding the key

fob, the location where the person holding the key fob is stationed, or the special purpose of the key fob button being depressed.

See the next page on Key Fob Transmitters as Zone Input Devices .

INTERIOR BYPASS FIRE/TBL SYS TBL CHIME

GEM-RP3DGTL/GEM-K3DGTL AND GEM-RP4RFC/GEM-K4RF KEYPAD EASY PROGRAM MENU

Other manuals for GEM-P9600

This manual suits for next models

Table of contents

Other Gemini Control Panel manuals

Gemini

Gemini X 255 - User manual

Gemini

Gemini GEM-P801 User manual

Gemini

Gemini Gemini GEM-P1664 User manual

Gemini

Gemini GEM-P816 User manual

Gemini

Gemini Gemini GEM-P3200 User manual

Gemini

Gemini P 1632 User manual

Gemini

Gemini Gemini GEM-P3200 Installation manual

Gemini

Gemini GEM-P816 User manual

Gemini

Gemini GEM-P9600 User guide

Popular Control Panel manuals by other brands

Kipor

Kipor KP310 user manual

Sony

Sony MKS-R4020 operating instructions

Brivo

Brivo ACS100 installation manual

FBI

FBI XL1218R user guide

Pujol

Pujol SHYRA AC F SL 600 PJ installation manual

STG-BEIKIRCH

STG-BEIKIRCH SHE TRZ Basic 2A/BMA Technical information and operating instruction

NAPCO

NAPCO Magnum Alert 1008LK installation instructions

BFT

BFT ALENA SW2 CPEM installation manual

Essmann

Essmann TRZ Basic DG Technical information and operating instruction

Unical

Unical Ufly BOX Installation and Servicing Manual

Johnson Controls

Johnson Controls IQ4 NS installation manual

Honeywell

Honeywell NOTIFIER INSPIRE E10 operating instructions

AMX

AMX ProLink PRO-DP8 quick start guide

Fromm

Fromm FR330 Translation of the original instructions

STG-BEIKIRCH

STG-BEIKIRCH TRZ Basic 4A Technical information and operating instruction

GE Allegro user manual

ERNITEC

ERNITEC 1504M instructions

GAS

GAS Gasmaster Installation, operation and maintenance manual

Gemini GEM-P9600 Installation manual

Popular Control Panel manuals by other brands