Genie PWIP4BVAF User manual

Quick Start Guide
Please read these instructions carefully before operating the unit
and keep for further reference.
4MP H.265 IP IR Bullet Camera
with 2.8-12mm Auto Focus
Lens
PWIP4BVAF | PWIP4BVAFG

ii
Intro Section
Please read this instruction carefully before operating the product and keep it for further
reference. All examples and pictures used here are for reference only.
The contents of this manual are subject to change without notice.
CAUTION:
• If the product does not work properly, please contact your dealer or the nearest service
centre. Never attempt to disassemble the camera yourself. We shall not be responsible
for any problems caused by unauthorised repair or maintenance.
• Do not allow water or liquid into the camera while in use.
• When using the product, you must be in strict compliance with the electrical safety
regulations of the nation and region.
• When the product is mounted on wall or ceiling, the device needs to be firmly fixed.
• Make sure the power supply voltage is correct before using the camera.
• Do not drop the camera or subject it to any physical shock.
• If cleaning, please use a clean soft cloth with a little neutral detergent to wipe it gently.
• Do not aim the camera at the sun or in any area where there is bright lighting.
• The device may be burned out by a laser beam, so when any laser equipment is in use,
make sure that the surface of the device will not be exposed to the laser beam.
• Do not place the camera in extremely hot, cold , dusty or damp locations, and do not
expose it to high electromagnetic radiation.
• To avoid heat accumulation, good ventilation is required for operating environment.

Contents
iii
1.0 Introduction..........................................................................................................4
1.1 Product Features...........................................................................................4
1.2 Product Dimensions.....................................................................................4
1.3 Contents ......................................................................................................4
1.4 Specification ................................................................................................5
2.0 Overview..............................................................................................................6
3.0 Installation............................................................................................................7
4.0 Network Connection ...........................................................................................8

4
The Genie PWIP4BVAF and PWIP4BVAFG are 4MP IP IR bullet cameras with a 2.8–12mm
varifocal auto focus lens. The cameras also feature up to 50m IR night view distance as well
as being IP67.
1.1 Product Features
• NDAA compliant
• 4MP (2560 × 1440) H.265 coding
• Maximum resolution: 2560 × 1440
• ICR auto switch, true day / night, ROI coding
• 3D DNR, digital WDR, HLC, BLC, defog
• 30~50m IR night view distance
• Supports remote monitoring by smart phones and tablet PCs with iOS and Android OS
• Intelligent analytics : Object removal detection, abnormal video signal detection, line
crossing detection and region intrusion detection
• DC12V / PoE power supply
• IP67 ingress protection
• Supports three streams
1.2 Product Dimensions
1.3 Contents
1.0 Introduction
217.7mm
Camera Quick Start Guide 4 Tapping Screws PA 4×25
1 Machine Screw PWM3×5
CD Drill Template Rubber Plug Plastic Plug x4
80.5mm

Quick Start Guide 4MP H.265 IP IR Bullet Camera with 2.8-12mm Auto Focus Lens
5
1.4 Specification
Camera
Image Sensor 1 / 2.7 “CMOS
Image Size 2560 × 1440
Electronic Shutter 1 / 25 s ~ 1 / 100000 s
Iris Type Fixed Iris
Minimum Illumination 0.011 Lux @ F1.2, AGC ON, 0 Lux with IR
0.04 Lux @ F2.26, AGC ON, 0 Lux with IR
Lens 2.8~12mm @ F1.4, Horizontal field of view: 94°~35.7°
Lens Mount M12 or Φ14 optional
Wide Dynamic Range Digital WDR
BLC Yes
HLC Yes
Defog Yes
Digital NR 3D DNR
Angle Adjustment Pan: 0°~360°,Tilt: 0°~90°, Rotation: 0°~360°
Image
Video Compression H.265, H.264
H.265 Compression
Standard Main Profile @ Level 4.1 High Tier
Resolution 4MP (2560 × 1440), 3MP (2304 × 1296), 1080p (1920 × 1080),
720p (1280 × 720), D1, CIF, 480 × 240
Main Stream 60Hz: 4MP, 3MP, 1080p (1~30fps),
50Hz: 4MP, 3MP, 1080p (1~25fps)
Sub Stream 60Hz : 720p (1~15fps), D1 (1~30fps), CIF (1~30fps)
50Hz: 720p (1~12fps), D1 (1~25fps), CIF (1~25fps)
Bit Rate 64 Kbps ~ 5 Mbps
Bit Rate Type VBR / CBR
Image Settings ROI, Saturation, Brightness, Chroma, Contrast, Wide Dynamic, Sharpen,
NR, etc. adjustable through client software or web browser
ROI Each ROI to be configured separately
Functions
Remote Monitoring Web browsing, CMS remote control
Online Connection Supports simultaneous monitoring for up to 4 users. Supports multi-
stream real time transmission
Network Protocol UDP, IPv4, IPv6, DHCP, NTP, RTSP,
PPPoE, DDNS, SMTP, FTP, 802.1x, UPnP, HTTP, HTTPs, QoS
Interface Protocol Onvif compatible
Intelligent Analytics Region intrusion detection, Object removal detection,
Abnormal video detection, Line crossing detection
Storage Network remote storage
Smart Alarm Motion detection
General Function Watermark, IP address filtering, video mask, heartbeat, password
protection
PoE Yes
IR Distance 30 ~ 50 m
Interface
Network RJ45
Video Output No
Audio No
Storage No
Hardware Reset No
Others
Ingress Protection IP67
Power Supply DC12V / PoE
Power Consumption < 9W
Operating Environment - 30°C ~ 60°C (-22°F~140°F), Humidity: Less than 95 % (Non-condensing)
Dimensions 217.7 × 80.5 × 80.5 mm
Weight Approximately 0.65Kg (Net)

6
2.0 Overview
Security Cap
DC12V
1. Fixed Ring
2. Mounting Base
3. Network Connector
4. Power Connector
5. Micro SD Card Slot
6. Reset
7. Focus
8. Zoom
1. Loosen the nut from the main element.
2. Run the network cable (without RJ 45 connector) through both elements. Then crimp
the cable with RJ 45 connector.
3. Connect the cable to the hermetic connector. Then tighten the nut and the main
cover.
Connecting Network Cable
• It is recommended to install the security cap for outdoor installation.
• If the PoE switch is used to power the camera, DC12V power supply is not required.

7
Please make sure that the wall or ceiling is strong enough to withstand 3 times the weight
of the camera. Please install the camera in and under a dry environment.
1. Drill the screw holes and the cable hole on the wall according to the drill template.
2. Route and connect the cables.
3. Secure the mounting base with camera to the wall with the screws provided.
4. Bracket adjustment. Before adjustment, preview the image of the camera on a monitor
and then loosen the fixed ring to adjust the view angle of the camera.
5. Open the cover of the camera and then insert a micro SD card. After that, adjust Zoom
or Focus to obtain an optimum image (If the camera is fixed or motorised lens, please
skip this step). Before adjustment, preview the image of the camera on a monitor.
3.0 Installation
Rubber Plug
Fixed Ring
360° Pan
90° Tilt
Cover
Focus
Zoom
Insert a Micro
SD card
360° Rotation
6. Install the cover back to the camera
and fix it firmly with the screws. (Note
that the cover should not be installed
unevenly).

8
Access the Camera through the IP Tool
1. Make sure that the camera and the PC are well connected via LAN.
2. Find the IP-Tool from the CD and then install it in the computer. After that, run the IP
Tool as shown below.
3. Modify the IP address. The default IP address of this camera is 192.168.226.201. Click the
information of the camera listed in the above table to show the network information
on the right hand. Modify the IP address and gateway of the camera and make sure its
network address is in the same local network segment as that of the computer. Please
modify the IP address of your device according to the practical situation.
4. Double-click the camera listed in the IP-Tool or manually enter the IP address in
the address bar of the web browser to connect IP-CAM. Then follow directions to
download and install the plugin. Enter the username and password in the login
interface. The default username is admin; the default password is 123456.
4.0 Network Connection
For example, the IP address of your computer is 192.168.1.4. So the IP address of the
camera shall be changed to 192.168.1.X and the gateway shall be changed to 192.168.1.1.
After modification, please enter the password of the administrator and click “Modify”
button to modify the settings. The default password of the administrator is “123456”.

Sales [phone]
Enquiries [email protected]o.uk
Website www.genieproducts.co.uk