Genie TPH-4000P User manual

Quick Start Guide
Please read these instructions carefully before operating the unit
and keep for further reference. All the examples and pictures used
here are for reference only. The contents of this manual are subject
to change without notice.
Side Opening Mid-Sized
External Housing with Heater
and PoE
TPH-4000P

Quick Start Guide Side Opening Mid-Sized External Housing with Heater and PoE
2
The Genie TPH-4000P is a mid-sized side opening external housing with a
heater and PoE in a die-cast aluminium alloy powder coated finish.
Features
• Pressure die-cast aluminium alloy construction with powder coated finish
• PoE (Power over Ethernet)
• Fully cable managed bracket
• Adjustable sliding camera tray
• Side-hinged top cover for easy access
• Includes DC12V heater
• IP67 ingress protection
Specifications
Dimensions
Finish Light ivory powder coated finish
Cable Inlet 2 x PGA 13.5 (Ø to 8.8 mm)
Heater DC12V heater switches on at 18°C and off at 28°C
Heater Current 1.12A (DC12V)
Power Supply Input PoE 802.3at (30 watt)
Power Supply Output PoE 802.3af (125.4 watt)
Ingress Protection IP67
External Dimensions
(W x H x D) 110 × 95 × 405 mm
Internal Dimensions
(W x H x D) 90 × 70 × 200 mm
Weight Housing : 1.95Kg Bracket : 0.66Kg
405mm
Side
89mm
Bottom
370mm
126mm
50mm
55mm
83mm
110mm
95mm

Quick Start Guide Side Opening Mid-Sized External Housing with Heater and PoE
3
Mounting Configuration
Fitting Instructions for Camera
Wiring Diagram
Inside the internal wiring diagram of TPH-4000P for the window demister. A spare 6
way terminal block is provided at the rear of the housing for the camera
when necessary and lens connections. Circuit identified as follows:
Adjust position
and direction
Cable Gland
Blower
Terminal Block
PoE Power Unit
RJ45 DC48V
to IP CAM
Camera Mounting Platform
DC12V Defogging Heater
RJ45 Connector to Injector

Quick Start Guide Side Opening Mid-Sized External Housing with Heater and PoE
4
AC Power Connection
Shows how to connect the AC power cord to the TB. 1 connector. This is spare for
AC power source input/output for AC accessory, it may not necessary to use in PoE
enclosure.
Installation
If you plan to install this camera into a tropical, sear coastal, saltwater or corrosive
industrial water/moist environment, please seal each stainless steel screw and
fittings with a silicon grease compounds. This will help prevent electrolysis
corrosive occurring and extend the lifespan of the camera and housing.
Caution :
1. UTP Category 5 cable is recommended to field construction.
2. Input CAT 5 wire must be 8 core line with standard RJ45 male connector.
3. A workable length is not exceed 100 Meters CAT 5 cable from PoE Hub Switch
to TPH-4000P, no guarantee if CAT5 cable beyond 100 Meters.
4. The second heater & IR illuminator are option and IEEE802.3at Injector
(TPH948/IJ) is necessary to connect in between PoE hub switch and PoE
enclosure.
RJ45 In/Out Pin Define & Connection
1. PoE Hub Switch end point with 48VDC output is an IEEE802.3af regulation de-
vice through pin 4,5,7,8 or 1,2,3,6 power device (PD).
2. An IEEE802.3at regulation power source equipment (PSE), a PoE injector is
strongly recommend to connect in between PoE hub switch and PoE housing.

Quick Start Guide Side Opening Mid-Sized External Housing with Heater and PoE
5

Sales [phone]
Enquiries [email protected]o.uk
Website www.genieproducts.co.uk