Genius Speed Slicer Plus Operating manual

Quick Use Guide
Blade Protector
To remove the V-Blade Protector before using the slicer, simply lower the
cutting platform to number 4. Place forefinger in circle of blade protector and
gently slide back until the protector is clear from blade. Use caution as the
blades are very sharp. For safe storage, place the guard back on blade and
gently pull protector back in place. Make sure to raise the cutting platform to
lock.
Food Container
*Tip: Occasionally, shake or move the food to the back of the container to
avoid food backup!
Easy Slice Stand
Your Speed Slicer Plus comes with a handy easy slice stand for counter top or
cutting board slicing. To use, insert both ends of the stand into the two holes
underneath the machine on the handle side and push all the way in. To remove,
place the Speed Slicer upside down on your counter and gently pull up until it
releases from the machine.
Your Speed Slicer Plus comes with a convenient 14
cup clear food/storage container and locking stay
fresh lid. You can prepare your foods directly into
the container by placing the front of your Speed
Slicer Plus on the front of the container and rest the
handle side on the back of the container. Always
hold the grip handle with one hand while cutting.
PLEASE BE VERY CAREFUL
WHEN HANDLING THE
SPEED SLICER PLUS!
BLADES ARE VERY SHARP!

2
Slicing Dial
There are 8 numbers on the select a slice dial. Please note the following
1-3 Thin slicing/shredding
4-6 Medium slicing/shredding
7-8 Thick slicing/shredding
French Fry, Julienne and Chopping Dial
Setting 1: Locked position
Setting 2: French Fries, chopping and dicing
Setting 3: Julienne strips, fine dicing and mincing
* You may set the select a slice dial to any number with these blades for the
perfect slice and size for every recipe.
Handy Grip:
Lay the food to be cut on the cutting platform. Place
the handy grip over the food and push down so the
pins grip the food. This will raise the food plunger
letting you know you’re ready to prepare the foods.
Slide the handy grip back and forth over the blades as
you place light pressure on the top food plunger to
feed the food into the blades. * On both sides of the
handy grip are spiked indentations to hold food such as
carrots, zucchini, and cucumbers.
Handy Grip was designed for easy and safe cutting
with the Speed Slicer Plus. It has five stainless steel
pins to firmly grip foods and a food plunger for easy
and total food preparation

3
Handy Hopper
To use you handy hopper, slide hopper to bottom of
your speed slicer. Press the two clips inward on both
sides of the lid and gently lift to remove the top cover.
Place your foods into in the handy hopper,
Replace the top cover making sure the clips are
snapped into position. Slide the hopper up and down
your speed slicer using long even strokes. Now you are
now ready for speed slicing! * Make sure the handy
hopper is attached to the speed slicer and at the bottom
of the machine when refilling with food.
CAUTION, BLADES ARE SHARP. EXERCISE EXTREME CAUTION WHEN
HANDLING SLICER!!!
Cleaning:
To clean you speed slicer, set the slicing dial to lock and the FF –Julienne
blades to closed position. Use soapy water and a sponge to clean your speed
slicer then rinse clean with hot water. To clean julienne blades, turn your speed
slicer over to the dial side and lay flat. Unlock the slicing dial to max. On each
side of the julienne blade dial are 2 clips. Press clips inward and lift up to
expose blades. Use a bristle brush to remove food particles and rinse under hot
water. (Never use fingers to remove foods) Flip platform back into cutting
position; slide each clip outward to lock back into place. Turn speed slicer over
to the top position, carefully replace the blade guard and turn the slicing dial to
lock.
Hold the grip handle and slide the Handy Hopper
onto the slicer by putting the runners into the
grooves on the side. The hopper should slide easily
in the rails and stop at the end. Now the food can
loaded into the container. * For speed slicing, place
a small amount of cooking oil on a Q-tip and apply
to the inside groove on each side of the speed slicer.