GeoVision GV-AS100 User manual

GV-AS / EV Controller
Quick Start Guide
ASEV-QG-E
Thank you for purchasing GV-AS / EV Controller. This guide is designed to assist the new user in
getting immediate results from the controllers. For advanced information on how to use the GV-
AS100 / 1010 / 110 / 1110 / 120 / 210 / 2110 / 2120 / 410 / 4110 / 810 / 8110 and GV-EV48, please
refer to GV-AS / EV Controller User's Manual on Software CD / DVD.

© 2015 GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part,
without the written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is
accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind
and assumes no responsibility for errors or omissions. No liability is assumed
for incidental or consequential damages arising from the use of the information
or products contained herein. Features and specifications are subject to
change without notice.
Note: No memory card slot or local storage function for Argentina.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: [phone]
Fax: [phone]
http://www.geovision.com.tw
Trademarks used in this manual: GeoVision, the GeoVision logo and GV
series products are trademarks of GeoVision, Inc. Windows and Windows XP
are registered trademarks of Microsoft Corporation.
October 2015

October 29, 2015 i
Contents
Contents...........................................................................................................................i
Important Note for Maintaining Power Supply..................................................................ii
GV-AS Controller Quick Start Guide............................................................................... 1
1. Basic Setup for GV-AS100 / 1010 / 110 / 1110 / 120................................................. 1
1.1 GV-AS100 / 1010 ............................................................................................. 2
1.2 GV-AS110 / 1110 ............................................................................................. 3
1.3 GV-AS120 ........................................................................................................ 4
2. Physical Wiring for GV-AS210 / 2110 / 2120 / 410 / 4110 / 810 / 8110 and GV-EV48 5
2.1 GV-AS210 / 2110 / 2120 .................................................................................. 5
2.2 GV-AS410 / 4110 / 810 / 8110.......................................................................... 6
2.3 GV-EV48.......................................................................................................... 7
3. Accessing the Web Interface of the GV-AS Controllers ............................................. 8
4. Setting GV-AS Controller on GV-ASManager............................................................ 9
5. Optional Devices for GV-AS100 / 110 / 120..............................................................10
5.1 Physical Wiring of GV-ASBox and GV-ASNet .................................................11
5.2 Accessing the Web Interface of GV-AS100 / 110 / 120....................................12

October 29, 2015 ii
Important Note for Maintaining Power Supply
To make sure GV-AS / EV Controllers can function properly during a power outage, be sure
to replace the internal battery on the controllers when needed. It is also recommended to
install a backup battery for compatible GV-AS Controllers.
Refer to the following sections in GV-AS Controller User Manual for instructions on how to
install a backup battery:
zGV-AS100 / 110 / 120 through GV-ASBox: See 9.1.4.F Connecting Backup Battery.
zGV-AS100 / 110 / 120 through GV-ASNet: See 9.2.4.F Connecting Backup Battery.
zGV-AS210 / 2110 / 2120: See 4.2.4 Connecting Backup Battery
zGV-AS410 / 4110 / 810 / 8110: See 5.2.4 Connecting Backup Battery
zGV-EV48: See 6.2.3 Connecting Backup Battery.
Replaceable Button Cell (GV-AS100 / 2110 / 2120 / 4110 / 8110)
For GV-AS100 / 2110 / 2120 / 4110 / 8110, you can replace the battery on your own when
you see low battery messages and icons in GV-ASManager.
Note: Make sure the plastic insulation film under the battery is removed when using GV-
AS100 / 2110 / 2120 / 4110 / 8110 for the first time. The low battery messages and icons will
appear if the plastic film is not removed.

October 29, 2015 iii
Built-in Battery (GV-AS1010 / 110 / 1110 / 120 / 210 / 410 / 810 & GV-EV48)
When the controller runs out of battery, the local time on the controller will be reverted back
to 1999/12/31. The controller time can be found on the Web interface of the controller on the
Time Setting page and in the Access Monitor / Alarm Monitor / Event Monitor of GV-
ASManager.
When you see the controller year shown as 1999 or 2000, disconnect the controller from
power and reconnect it to power. If the year is still shown as 1999 or 2000, the controller
battery needs to be replaced. When this occurs, connect the controller to a backup battery
and maintain connection with GV-ASManager at all times. When connected to GV-
ASManager, the controller’s time will be synchronized with GV-ASManager’s time.

October 29, 2015 1
GV-AS Controller Quick Start Guide
This guide lists the basic steps required to set up a GV-AS Controller. For detailed
instructions, refer to the section number listed below each step.
1. Basic Setup for GV-AS100 / 1010 / 110 / 1110 / 120
This section covers the basic settings required to start running GV-AS100 / 1010 / 110 / 1110
/ 120. For more settings on GV-AS100 / 110 / 120, refer to 5. Optional Devices for GV-AS100
/ 110 / 120. The section numbers listed here refers to the GV-AS Controller User Manual.

October 29, 2015 2
1.1 GV-AS100 / 1010
1.3 Programming Mode
1.2.5 Connecting the Power
1.2.4 Connecting the PC
1.2.3 Connecting Output Devices
1.2.2 Connecting Input Devices
1.2.1 Connecting Card Readers
Connect card readers (Optional)
Connect AS100 / 1010 to a reader.
Connect input devices
Connect AS100 / 1010 to input devices (Ex: a push button to
exit).
Connect output devices
Connect AS100 / 1010 to output devices (Ex: a door lock).
Connect to PC
Connect the controller to a computer through RS485
connection (AS100) or network connection (AS100 & AS1010).
Connect to Power
Connect AS100 / 1010 to power using the supplied adaptor.
Programming the GV-AS100 / 1010
Create a Master Card (AS100) or Enroll / Delete Card
(AS1010) to add and delete cards. For other settings, use the
built-in keypad to type the commands.
GV-AS100
GV-AS1010

October 29, 2015 3
1.2 GV-AS110 / 1110
2.3 Programming Mode
2.2.5 Connecting the Power
2.2.3 Connecting Output Devices
2.2.2 Connecting Input Devices
2.2.1 Connecting Card Readers
Connect card readers (Optional)
Connect AS110 / 1110 to a reader..
Connect input devices
Connect AS110 / 1110 to input devices (Ex: a push
button to exit).
Connect output devices
Connect AS110 / 1110 to output devices (Ex: a door
lock).
Connect to Power
Connect AS110 / 1110 to power using the supplied
adaptor.
Programming the GV-AS110 / 1110
Create an Enroll Card and a Delete Card to add and
delete cards. For other settings, use the built-in keypad
to type the commands.
GV-AS110 / 1110
2.2.4 Connecting the PC
Connect to PC
Connect the controller to a computer through RS485
connection (AS110) or network connection (AS110 &
AS1110).

October 29, 2015 4
1.3 GV-AS120
3.2.1 Connecting a Wiegand Reader
Connect card readers (Optional)
Connect AS120 to a reader through Wiegand
interface.
Connect input devices
Connect AS120 to input devices (Ex: a push
button to exit).
3.2.2 Connecting Input Devices
Connect output devices
Connect AS120 to output devices (Ex: a door
lock).
3.2.3 Connecting Output Devices
Connect to PC
Connect AS120 to a computer through RS485
connection or network connection.
Connect to Power
Connect AS120 to power using the supplied 12V
DC adaptor.
3.2.5 Connecting the Power
RS485 Connection
3.2.4.A RS-485 Connection
Network Connection
3.2.4.B Network Connection
Add and delete cards
Create an Enroll Card and a Delete Card to add
and delete cards.
3.3 Programming Mode
GV-AS120

October 29, 2015 5
2. Physical Wiring for GV-AS210 / 2110 / 2120 / 410 / 4110 /
810 / 8110 and GV-EV48
2.1 GV-AS210 / 2110 / 2120
4.2.6 Connecting the PC
4.2.5 Connecting the Power
4.2.4 Connecting Backup Battery
4.2.3 Connecting Output Devices
4.2.2 Connecting Input Devices
Wiegand
4.2.1.A Wiegand Readers
RS485
4.2.1.B RS-485 Readers
Connect card readers
Connect AS210 / 2110 / 2120 to readers through
Wiegand or RS-485 interface.
Connect input devices
Connect AS210 / 2110 / 2120 to input devices
(Ex: a push button to exit).
Connect output devices
Connect AS210 / 2110 / 2120 to output devices
(Ex: a door lock).
Connect Backup Battery (Optional)
Connect AS210 / 2110 / 2120 to backup battery
in case the main power supply fails.
Connect to PC
Connect AS210 / 2110 / 2120 to a computer to
access its Web interface and connect with GV-
ASManager.
Connect to Power
Connect AS210 / 2110 / 2120 to power using a
12V DC adaptor (or a PoE adapter for AS2120).
GV-AS210 / 2110 / 2120