GeoVision GV-CS1320 User manual

GV-CS1320 Camera Access Controller
Quick Start Guide
CS1320V308-QG-A
Thank you for purchasing GV-CS1320 Camera Access Controller. This guide is designed to assist the new
user in getting immediate results from the controllers. For advanced information on how to use GV-CS1320,
please refer to GV-CS1320 Camera Access Controller User's Manual on Software CD / DVD.

© 2021 GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part,
without the written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is
accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind
and assumes no responsibility for errors or omissions. No liability is assumed
for incidental or consequential damages arising from the use of the information
or products contained herein. Features and specifications are subject to
change without notice.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: [phone]
Fax: [phone]
http://www.geovision.com.tw
Trademarks used in this manual: GeoVision, the GeoVision logo and GV
series products are trademarks of GeoVision, Inc. Windows is the registered
trademark of Microsoft Corporation.
October 2021
Scan the following QR codes for product warranty and technical support
policy:
[Warranty] [Technical Support Policy]

Contents
Installation Considerations...................................................................i
1. Introduction ....................................................................................1
1.1 Packing List........................................................................................................... 1
1.2 Compatible Software Versions............................................................................... 2
1.3 Overview................................................................................................................ 3
2. Installation ......................................................................................5
3. Connecting the Camera .................................................................6
3.1 Connecting RS485 Readers .................................................................................. 6
3.2 Connecting Network Readers................................................................................ 7
3.3 Connecting Input Devices...................................................................................... 7
3.4 Connecting Output Devices ................................................................................... 8
3.5 Connecting GV-CS1320 to PC............................................................................... 9
3.6 Connecting the Power...........................................................................................10
4. Accessing the GV-Fisheye Camera.............................................11
4.1 Creating Login Credentials....................................................................................11
4.2 Web Browser........................................................................................................12
4.2 Looking Up the Dynamic IP Address and Logging In ............................................12
4.3 Configuring the IP Address...................................................................................14
5. The Web Interface.........................................................................15
6. Upgrading System Firmware.......................................................16
7. Restoring to Factory Default........................................................17

i
Installation Considerations
To make sure the finger and face of the cardholder can be detected, follow the instructions
below to set up GV-CS1320.
Bell Button Recognition:
The bell button cannot be responded with gloves on.
Installation Height:
When placed at a building gate, GV-CS1320 should be about 1.4-1.5 meters above the
ground.
When placed at a parking lot gate, GV-CS1320 should be about 1.2 meters above the
ground to match the height of vehicles.
Face Detection Limitations
GV-CS1320 cannot detect the face of cardholders wearing facial masks or sunglasses.
GV-CS1320 is designed to detect front-view faces only. If the face is slightly tilted
horizontally or vertically, the tilt angle cannot exceed 15° degree.
Lighting Conditions
Avoid placing GV-CS1320 where the light source is directly behind the subject.
Prevent light from directly falling onto the GV-CS1320’s camera lens.

1. Introduction
Welcome to the GV-CS1320 Camera Access Controller Quick Start Guide. In the following
sections, you will learn the basic installations and configurations of GV-CS1320. For details,
see GV-CS1320 Camera Access Controller User’s Manual.
1.1 Packing List
GV-CS1320 Mounting Plate
Standard Screw x 2 Plastic Screw Anchor x 2
Security Tube Torx Wrench
Silica Gel Bag
Software
DVD
Micro SD Card 2 GB (formatted and installed)
Warranty Card
1

1.2 Compatible Software Versions
The GeoVision software versions compatible with GV-CS1320 are listed below.
GV-VMS: V15.10 or later
GV-DVR / NVR: V8.6.2.0 (with Patch) or later
GV-Control Center: V3.3.0.0 (with Patch) or later
GV-Redundant Serer / Failover Server: V1.1.0.0 (with Patch) or later
GV-Recording Server: V1.2.5.0 (with Patch) or later
GV-Edge Recording Manager: V1.1.0.0 (with Patch) or later
The compatible versions between GV-CS1320 and GV-ASManager:
GV-CS1320 V1.0 V1.10 V1.11 V2.00 V2.11 V2.20
GV-ASManager V4.3.5.0 V4.3.5.0
V4.4.0.0 V4.4.2.0
V4.4.3.0 V5.0.0.0 V5.0.1.0 V5.0.2.0
GV-CS1320 V3.00 V3.01 ~
V3.03
V3.04 ~
V3.05 V3.06 V3.07~V3.08
GV-ASManager V5.1.1 V5.2.0 V5.3.0 V5.3.1 V5.3.2
2

Introduction
1
1.3 Overview
No. Name Function
1 Lens Receives image.
2 Microphone Receives sound from GV-CS1320.
3 Card Reader Reads ID cards or ID tags.
4 IR LEDs Automatically illuminates for night time use.
5 Speaker Talks to the surveillance area from the local computer.
6 Touchpad and LED
status Touch to activate the talk mode. See the LED and Beeper Status below.
7 Default Button Resets all configurations to default factory settings. See 7
Restoring to Factory Default.
8 Power Cable Connects to power supply. See 3.6 Connecting the Power.
9 Ethernet Port Connects to network and power supply. See 3.5 Connecting
GV-CS1320 to PC.
3

4
LED and Beeper Status
Condition LED Beeper
Ready Blue (Connected to
GV-ASManager)
Purple (Disconnected from
GV-ASManager)
N/A
Access Denied Displays red LED
momentarily Two short beeps
Access Granted Displays green LED
momentarily One long beep
Touchpad activated Flashes blue momentarily One short beep
Touchpad ignored Returns to blue/purple LED Three short beeps after 30
seconds
Wire Definition
Wire Definition
RJ-45 Ethernet
Red 12V DC
Black GND
Yellow Input 1
Brown Input COM
Light Red Input 2
Blue RS-485 +
Light Blue RS-485 -
Gray Output NO
Purple Output COM
Orange Output NC
Green Not functional
White Not functional

2. Installation
After the location of your GV-CS1320 is decided, follow the steps below to install the camera
access controller. You will need to prepare a single gang power box for wall mount
installation.
1. Attach the single gang power box to the wall.
2. Place the mounting plate on the single gang power box and secure with the 2 standard screws
provided.
3. Place GV-CS1320 on the mounting plate together with the single gang power box and thread the
cables through the holes.
4. Secure the security screw on the bottom with the mounting plate.
Step 2
Step 3
Step 4
5

3. Connecting GV-CS1320
3.1 Connecting RS485 Readers
You can establish RS-485 connection with any GV-Readers. GV-CS1320 can connect with up
to 2 readers. You need two power wires and two RS-485 wires from one reader to
GV-CS1320. When connecting a second reader to GV-CS1320, you will need to set up a
separate power source to power the second reader if the total power consumption (including
output devices) exceeds 12V.
The table below shows the wire assignments of RS485 connection on GV-CS1320.
6
Wire color Definition
Red 12V DC
Black GND
Blue RS-485 +
Light Blue RS-485 -