GeoVision GV-TFD Series User manual

GV-IP Camera
Quick Start Guide
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual forfuture use. UBN-QG-ZC
GV-ABL / TBL Series, GV-TBLP5800
GV-ADR / TDR Series
GV-AVD / TVD Series
GV-BLFC5800
GV-EBD Series, GV-EBDP5800
GV-EBFC5800
GV-FER5702
GV-PTZ5810-IR
GV-TFD Series

©2023GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part,
without the written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is
accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind
and assumes no responsibility for errors or omissions. No liability is assumed
for incidental or consequential damages arising from the use of the information
or products contained herein. Features and specifications are subject to
change without notice.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: [phone]
Fax: [phone]
http://www.geovision.com.tw
Trademarks used in this manual: GeoVision, the GeoVision logo and GV
series products are trademarks of GeoVision, Inc. Windows is the registered
trademark of Microsoft Corporation.
December 2023
Scan the following QR codes for product warranty and technical support
policy:
[Warranty] [Technical Support Policy]

i
Contents
Note for Connecting to GV-VMS / DVR / NVR...............................................................................iii
Note for Installing Camera Outdoor .............................................................................................iii
Note for Powering the Camera......................................................................................................iii
Note for Face Detection.................................................................................................................iv
Note for People Counting...............................................................................................................v
1. GV-EBD Series, GV-EBFC5800, GV-EBDP5800 ......................................................................1
1.1 Packing List..........................................................................................................................2
1.2 Overview...............................................................................................................................3
1.2.1 GV-EBD2702 / 2704 / 4700 / 4701 / 4704 / 8700 / 8800 and GV-EBFC5800..................................... 3
1.2.2 GV-EBD4711 / 4712 / 4813 / 8711 / 8813, GV-EBDP5800.................................................................... 4
1.3 Installation ............................................................................................................................5
1.3.1 GV-EBD2702 / 2704 / 4700 / 4701 / 4704 / 8700 / 8800 and GV-EBFC5800 Installation................. 5
1.3.2 GV-EBD4711 / 4712 / 4813 / 8711 / 8813 Installation............................................................................. 8
2. GV-ABL / TBL Series, GV-BLFC5800, GV-TBLP5800............................................................ 11
2.1 Packing List ........................................................................................................................12
2.2 Overview.............................................................................................................................13
2.2.1 GV-ABL2701 / 2703 / 4701 / 4703 & TBL2703 / 2705 / 4703 / 4705 / 8804...................................... 13
2.2.2 GV-ABL2702 / 4711 / 4712 / 8712, TBL4700 / 4710 / 4711 / 4807 / 4810 / 8710 / 8810, and
BLFC5800 ................................................................................................................................................................ 15
2.3 Installation ..........................................................................................................................16
3. GV-ADR / TDR Series .............................................................................................................20
3.1 Packing List ........................................................................................................................21
3.2 Overview.............................................................................................................................22
3.3 Installation ..........................................................................................................................23
4. GV-AVD / TVD Series..............................................................................................................26
4.1 Packing List ........................................................................................................................27
4.1.1 GV-TVD4711 / TVD4811............................................................................................................................ 27
4.1.2 GV-AVD / TVD Series ................................................................................................................................ 28
4.2 Overview.............................................................................................................................29
4.2.1 GV-AVD2700 / 4710 / 8710, GV-TVD4700 / 4710 / 4810 / 8710 / 8810 ............................................ 29
4.2.2 GV-TVD4711 / TVD4811............................................................................................................................ 30
4.3 Installation ..........................................................................................................................32
4.3.1 GV-AVD2700 / 4710 / 8710, GV-TVD4700 / 4710 / 4810 / 8710 / 8810 ............................................ 32
4.3.2 GV-TVD4711 / TVD4811............................................................................................................................ 34
5. GV-TFD Series ........................................................................................................................36
5.1 Packing List........................................................................................................................36

ii
5.1.1 GV-TFD4700 / 4800................................................................................................................................... 36
5.2 Overview.............................................................................................................................37
5.2.1 GV-TFD4700 / 4800................................................................................................................................... 37
5.3 Installation ..........................................................................................................................38
5.3.1 GV-TFD4700 / 4800................................................................................................................................... 38
6. GV-FER5702............................................................................................................................39
6.1 Packing List ........................................................................................................................39
6.1.1 GV-FER5702............................................................................................................................................... 39
6.2 Overview.............................................................................................................................40
6.2.1 GV-FER5702............................................................................................................................................... 40
6.3 Installation ..........................................................................................................................41
7. GV-PTZ5810-IR .......................................................................................................................43
7.1 Packing List ........................................................................................................................43
7.1.1 GV-PTZ5810-IR.......................................................................................................................................... 43
7.2 Overview.............................................................................................................................44
7.2.1 GV-PTZ5810-IR.......................................................................................................................................... 44
7.3 Installation ..........................................................................................................................45
8. Waterproofing the Cable........................................................................................................47
9. Accessing the Camera...........................................................................................................49
9.1 System Requirements.........................................................................................................49
9.2 Looking Up the Dynamic IPAddress...................................................................................50
9.3 Configuring the IPAddress .................................................................................................51
10. The Web Interface ................................................................................................................52
11. Upgrading System Firmware...............................................................................................54
12. Restoring to Factory Default ...............................................................................................55

iii
Note for Connecting to GV-VMS / DVR / NVR
The GV-IPCAM is designed to work with and record on GV-VMS / DVR / NVR, a video management
system.
•Once the camera is connected to the GV-VMS / DVR / NVR, the resolution set on the GV-VMS /
DVR / NVR will override the resolution set on the camera’s Web interface. You can only change
the resolution settings through the Web interface when the connection to the GV-VMS / DVR /
NVR is interrupted.
•The login password of the camera cannot contain the character “&” or any whitespace when
connecting to GV-VMS.
•The Video Analytic features under Intelligent (See 3.6 Intelligent in the User’s Manual) cannot be
integrated with GV-VMS / DVR / NVR
Note for Installing Camera Outdoor
When installing the camera outdoor, be sure that:
1. The camera is set up above the junction box to prevent water from entering the camera along
the cables.
2. Any PoE, power, audio and I/O cables are waterproofed using waterproof silicon rubber or the
like.
3. The screws are tightened and the cover is in place after opening the camera cover.
Note for Powering the Camera
The camera is powered by PoE. If you want to power the camera using the power
connector, an optional power adapter is required.

iv
Note for Face Detection
To use the camera’s built-in face detection feature (see 3.6.1.7 Face Detectionin the User’s Manual),
which is only supported by certain models, it is recommended to install the camera according to the
criteria listed below
Surveillance Condition
•The camera shall be installed at a site with uniform, sufficient lighting, where the face(s) to be
detected are fully illuminated.
Example of Recommended Scene
Example of Non-recommended Scene
Camera Position
•The camera shall be mounted at a recommended height of 2.5 ~ 3 m (8.2 ~ 9.84 ft).
•The camera shall be mounted with a recommended depression angle of around 10°.
•The camera shall be positioned so that the face(s) to be detected are directly aligned with the
lens of the camera, with a horizontal deviation of no greater than 30°, a vertical deviation of no
greater than 15°and a face size of at least 120 pixels.
Surveillance
area width Horizontal line
Depression angle α
Optical axis of
the camera
Pedestrian walking direction
(straight along the center of
the ground)
Horizontal surveillance distance
Device mounting height

v
Note for People Counting
To use the camera’s built-in people counting feature (see 3.6.1.8 People Counting in the User’s
Manual), which is only supported by certain models, it is recommended to install the camera
according to the criteria listed below:
Surveillance Condition
•The camera shall be installed at a site with uniform, sufficient lighting, where the person(s) to be
counted are fully illuminated.
•The camera shall be installed at an entrance or exit with an ideal width of 1 ~ 4 m (3.28 ~ 13.12 ft),
where the persons(s) to be counted move toward the lens of the camera in single file.
Example of Recommended Scene
Example of Non-recommended Scene
Camera Position
•The camera shall be mounted at a recommended height of 3 ~ 5 m (9.84 ~ 16.4 ft).
•The camera shall be mounted with a recommended depression angle of 70 ~ 80°.
•The camera shall be positioned so that the person(s) to be counted face toward the lens of the
camera and are displayed on the image with a shoulder size of between 120 ~ 160 pixels.
Surveillance
area width Horizontal line
Depression angle α
Optical axis of
the camera
Pedestrian walking direction
(straight along the center of
the ground)
Horizontal surveillance distance
Device mounting height

1
1. GV-EBD Series, GV-EBFC5800, GV-EBDP5800
Camera Type
Model No.
Eyeball IP Dome
GV-EBD2702 (IP67)
GV-EBD2704 (IP67)
GV-EBD4700 (IP67)
GV-EBD4701 (IP67)
GV-EBD4704 (IP67)
GV-EBD4711 (IP67)
GV-EBD4712 (IP67)
GV-EBD4813 (IP67)
GV-EBD8700 (IP67)
GV-EBD8711 (IP67)
GV-EBD8800 (IP67)
GV-EBD8813 (IP67)
GV-EBDP5800 (IP67)
GV-EBFC5800 (IP67)

2
1.1 Packing List
The packing list varies depending on the model. Product details can be found on the
datasheet.
•Eyeball Dome
•Screw Kit
•Drill Template Paster
•Waterproof Rubber Set
•Download Guide
•Torx Wrench (not available for all models)

GV-EBD Series
3
1
1.2Overview
1.2.1 GV-EBD2702 / 2704 / 4700 / 4701 / 4704 / 8700 / 8800 and
GV-EBFC5800
No.
Description
1
Bottom ring
2
Housing
3
Lens
4
Infrared indicator / Warm LEDs (GV-EBFC5800 only)
5
Power connector (DC 12 V)
6
Ethernet connector / PoE
7
Micro SD card slot (GV-EBD2704 / 4701 / 4704 / 8800
and GV-EBFC5800 only)
8
Microphone (GV-EBD2704 / 4701 / 4704 / 8800 and
GV-EBFC5800 only)

4
1.2.2 GV-EBD4711 / 4712 / 4813 / 8711 / 8813, GV-EBDP5800
No.
Description
1
Bottom ring
2
Housing
3
Microphone
4
Lens
5
Power connector (DC 12 V)
6
Ethernet connector / PoE
7
Micro SD card slot and default button compartment
8
Default button
9
Micro SD card slot
Note: If the default button doesn’t respond after pressing for 15 seconds, reboot the
camera and try again within 10 minutes of rebooting.

GV-EBD Series
5
1
1.3Installation
The Target Eyeball Dome is designed for outdoors. With the standard package, you
can install the camera on the ceiling. Or you can purchase optional mounting
accessories to mount the dome on a wall.
Below are the instructions for Ceiling Mount. There are two kinds of Ceiling Mount:
Concealed Installation and Open Installation. In Concealed Installation, the cables
are hidden in the ceiling. In Open Installation, the cables are led out from the open slot
on the bottom ring.
1.3.1 GV-EBD2702 / 2704 / 4700 / 4701 / 4704 / 8700 / 8800 and
GV-EBFC5800 Installation
For Concealed Installation
1. Stick the drill template paster to the ceiling and drill three holes according to the
drill template.
Drill Template Paster
2. Insert the screw anchors.
Drill a hole to lead cables out of the ceiling
Knock in screw anchors
8

6
3. Remove the bottom ring by turning it anticlockwise.
Bottom Ring
4. Connect the cables and secure the camera.
Connect the cables and protect
them with waterproof tape
Attach the camera to ceiling
with screws
5. Adjust the monitoring direction.
The camera can rotate
360 degrees horizontally
The lens can rotate 80
degrees vertically

GV-EBD Series
7
1
6. Mount the bottom ring.
Push the bottom ring back up and turn
it clockwise to lock into position
For Open Installation
Lead the cables out from the open slot on the bottom ring before screwing the camera
to the ceiling as shown in step 4 of Conceal Installation.
Open slot on the bottom ring
Lock
Note: To adjust the monitoring direction at Step 5, loosen the screw indicated at the
Lock position as shown in the figure above. Tighten it when the adjustment is
completed.

8
1.3.2 GV-EBD4711 / 4712 / 4813 / 8711 / 8813 Installation
For Concealed Installation
1. Stick the drill template paster to the ceiling and drill three holes according to the
drill template.
Drill Template Paster
2. Insert the screw anchors.
Drill a hole to lead the cables out of the ceiling
Knock in screw anchors

GV-EBD Series
9
1
3. Loosen the fixing screw and remove the housing by turning it to the position as
shown.
1
4. Secure the bottom ring to the ceiling with 3 supplied screws and connect the
cable.
Connect cable and protect
it with waterproof tape
Attach bottom ring to
ceiling with taping screws
(Optional) insert a
micro SD card
5. Mount the housing by adjusting to the position as shown and press and turn to
anywhere but .
1

10
6. Adjust the monitoring direction. Then tighten the screw.
For Open Installation
Lead the cables out from the open slot on the bottom ring before screwing the camera
to the ceiling as shown in step 5 of Concealed Installation.
Open slot on the bottom ring
Note: You can optionally purchase GV-Mount211 or GV-Mount212 for Wall Bracket
Mount. For details, see its User’s Manual.

11
Camera Type
Model No.
Bullet IP Camera
GV-ABL2701 Series (IP66)
GV-ABL2702 (IP67 + IK10)
GV-ABL2703 Series (IP67)
GV-ABL4701 Series (IP66)
GV-ABL4703 (IP67)
GV-ABL4711 (IP67 + IK10)
GV-ABL4712 (IP67)
GV-ABL8712 (IP67 + IK10)
GV-TBL2703 Series (IP67)
GV-TBL2705 (IP67)
GV-TBL4700 (IP67 + IK10)
GV-TBL4703 (IP67)
GV-TBL4705 (IP67)
GV-TBL4710 (IP67 + IK10)
GV-TBL4711 (IP67 + IK10)
GV-TBL4810 (IP67 + IK10)
GV-TBL8710 (IP67 + IK10)
GV-TBL8804 (IP67 + IK10)
GV-TBL8810 (IP67 + IK10)
GV-TBLP5800 (IP67)
GV-BLFC5800 (IP67 + IK10)
2. GV-ABL / TBL Series, GV-BLFC5800, GV-TBLP5800

12
2.1 Packing List
The packing list varies depending on the model. Product details can be found on the
datasheet.
•
•Bullet IP Camera
•Waterproof Rubber Set
•Screw Kit
•Drill Template Paster
•Download Guide
•Torx Wrench (not available for all models)

GV-ABL Series
13
2
2.2 Overview
2.2.1 GV-ABL2701 / 2703 / 4701 / 4703 & TBL2703 / 2705 /
4703 / 4705 / 8804
No.
Description
1
Power connector (DC 12 V)
2
Ethernet connector / PoE
No.
Description
No.
Description
1
Load Default button
2
Grounding screw (GV-TBL8804)
Note: The Load Default button is for GV-ABL2703 / 4703 & GV-TBL2703 /
4703 / 8804 only.