GFW JASMINE GAS LIFT BED User manual

adults, on a clean flat surface, in the room in which it will be used.
3) Please do not discard any packing until you have checked that you have all the
parts and fittings.eep all fittings out of childrens reach, to avoid choking hazard.
HELPFUL
ADVICE PRIOR TO
ASSEMBLING THE BED
two
Do not throw away any of the packing until you have assembled the bed completely.
We recommend that you keep the assembly guide for future use.
From time to time, tighten the Quts and Eolts with Dllen key and spanner provided.
1) Owing to the size and weight of the bed, we recommend that it is assembled by
,
Page 1 of 9
IMPORTANT
If for any reason you need return this item, you must
return it in its original packing.
The Assembly guide explains carefully how to assemble the bed.
Please follow it step by step as you assemble the parts.
Check that you are using the correct parts.
Assembled items cannot be returned.
In the first instance, contact your service centre.
ASSEMBLY INSTRUCTION
JASMINE GAS LIFT BED

Headboard
Footboard
Front / Back frame rail x 2
Horizontal frame rail x 2
x 1
Cross bar
plastic bracket sets x 4 Corner brackets x 4 Frame support block x1 Adjustable legs x 4
Belt x 1
Fabric base x1
A
Bolt x16
B
EF
G
L
Flange nut x2
Spanner x1
Components
BOX 1 OF 2
Hardware
6mm Allen key x1
BCD
M8 x25mm M6 M6
HI
Bracket x 2
K
J
Flat washer
x8
Spring washer
x8
Flat washer
x16
M8
Spring washer
x16
M8
Bolt x2
M6x60mm
Bolt x4
M6x40mm
Bolt x4
M6x30mm
Bolt x8
M6x25mm
Bolt x4
M6x20mm
Bolt x8
M6 x16mm
Centre slat caps
x13 (single & double)
x15 (king)
Side slat caps
x26 (single & double)
x30 (king)
Slat
x26 (single & double)
x30 (king)
M
Sleeve nut x8
1
2
6
5
8
910 11 12 13 14
15 16 17 18 19
Page 2 of 9
Bracket x 2

Components
BOX 2 OF 2
Left side rail
Headboard end
Right side rail
Centre Support x 1
Headboard end
3
4
7
Page 3 of 9

Page 4 of 9
Step 1:
BC
1
12
3
C
4
1
B
11
11
12
B
C
3
12
11
B
C
4
Fix brackets (11&12) to side rails (3&4) making sure they are aligned
as shown in the picture. Use bolt (A),spring washer (B) & flat washer
(C), tighten carefully with allen key supplied - Do not Over-tighten.
Fit the bolts (A), spring washers (B), and flat washers (C) to the holes
in the headboard (1) & footboard (2) as shown . 
Note: Do not fully locate the bolts, but leave 10mm protruding.
Fit side rail (3 & 4) to headboard (1) & footboard (2) locating the
brackets (11 &12) behind the flat washers. Once all four corners are
located, fully tighten the bolts using the allen key.
B
C
23
11
BC
4
2
12

Step 4:
6PP allen key.
Fi Irame Vupport Elock
FiW Irame support block (13)
DE
1
3
F
6mm
D
and Flat washers
, Spring
10
E
F
L
13
2
Page 5 of 9
L

SPACE
Secure GAS-LIFT SWHP
Before connecting the stem the lifting mechanism is
should lift up and down freely with adequate
, ensure functioning
correctly - it clearance on
all sides.
Secure the stem onto the mechanism - fix into place by using flange
6PP
nuts (M) as shown.
cross bar
M
K
K
8
84
3
Page 6 of 9

I
9
6PP
6PP
Attach the horizontal frame rails
left / right frame
J
7
5
6PP
I
Sleeve
5
6
7
3
4
8
J
6
Page 7 of 9
G
G
H
H

Turn bed upright and attach fabric
base (18) to bottom of bed.
lightly
2
1
18
1
18
14
Page 8 of 9
4

15
16
15
17
16
Use only the belt (19) to lift and lower
the frame to avoid trapping your fingers.
16
17
15 16
7
19
Page 9 of 9

PROMPT
M
A B
C D
After assembly of complete bedstead, you find there is some friction with
Loosen A, B, C, D on relevant side of bed and side slat frame forward until
slat frame is equal both sides, Then tighten securely.
Headboard Headboard
Footboard Footboard
A
B
C
D
A
B
C
D
bed side when frame is down. Make certain bed is assembled square
- see step 2 on assembly instruction.