GFW LANCASTER CONSOLE HALL TABLE User manual

Size : (W)970 x (D)350 x (H)760 mm
970
760
Thank you for purchasing the CONSOLE HALL TABLE.
Please read the instructions carefully to ensure safe operation of the product.
350
Batchh No : PO# 2759
Page 1 of 16
LANCASTER - CONSOLE HALL TABLE ASSEMBLY INSTRUCTIONS

Page 2 of 16
This product is intended for a maximum weight of 15kgs and drawer load capacity 4kg each.
Do not exceed this weight.
Due to the size of this product we recommend that is assembled in the room intended for use.
When you ready to start, make sure that you have the right tools, plenty of space and a clean, dry area for
assembly
Unwrap all packaging materials and place the components on top of the carton box or not on a clean floor to
prevent it from scratching.
Check the pack and make sure you have all the parts listed.
Ensure that this product is fully assembled as illustrated before use.
Check all screws or bolts are tightened and inspect regularly.
This product should only be used on firm, level ground.
Keep small parts out of reach of children.
Make sure the legs remain in contact with the ground.
Tools not included.
DO NOT use power tools to construct this product.
DO NOT tighten screw until fully assembled.
DO NOT over tighten screw or bolts.
DO NOT use this product if parts are missing, damage or worn.
DO NOT stand or sit on this table.
We recommend the use of the wall strap provided for safety reasons. N.B. Wall fixings are not included -please
source suitable fixings for your wall type. If in doubt please consult a qualified tradeperson. Warning: Always
ensure the area to be drilled is free from hidden electrical wires, water and gas pipes.
It is essential that this unit is fixed to a wall with the fixings provided.
Never use scourers, abrasives or chemical cleaners.
To clean wipe with a sponge and soapy water. Do not use solvent based cleaners or detergents as they
can bleach or damage the product.

Side Panel (L) (30) x 320 x 735mm)A 1
BSide Panel (R) (30) x 320 x 735mm) 1
CTop Panel (25 x 350 x 370mm) 1
DBottom Panel (30) x 318 x 880mm) 1
EBack Panel ( 15 x 160 x 880mm) 1
FCentre Panel ( 15 x 295 x 140mm) 1
GFront panel Bar (15 x 80 x 880mm) 1
MDrawer Back (15 x 100 x 337mm)
HRear panel Bar (15 x 80 x 880mm) 1
IBottom Panel Bar (15 x 60 x 880mm) 1
J
K
Drawer Front (15 x 160 x 587mm) 2
Drawer Side (L) (15 x 100 x 250mm) 2
LDrawer Side (r) (15 x 100 x 250mm) 2
2
ZDrawer Bottom (3 x 244 x 386mm) 2
A
H
G
EF
B
C
I
D
J
K
L
M
Z
Page 3 of 16

5
3
2x
l
Poket Handle
(64hole mm)
4x
j
Drawer Slide
(250 mm)
4x
k
Drawer Slide
(250 mm)
1x
m
Allen Key
M4
5x
a
Unitar Screw
D6.3 x 40mm
8x
b
CSK Screw
M4.7 x 38mm
21x
c
Wooden Dowel
D8 x 30mm
9x
f
Csk Screw
M3.5 x 15mm
2x
e
Handle Screw
M6 x 1/2mm
22x
d
Minifix Bolt
M5 x 29mm
5x
g
Nail Leg
5 x 8 x 13.5mm
22x
h
Minifix Cam
D15 x 12mm
8x
i
Euro Screw
D6 x 9mm
Page 4 of 16
1x
o
Safety strap
(L-200 mm)
1x
n
Wall Plug

STEP 1
21 x
c
Parts Required Qty
Panel (A) 1
Panel (B) 1
Panel (D) 1
Panel (E ) 1
Parts Required Qty
Panel (F) 1
Panel (G) 1
Panel (H) 1
Panel (I ) 1
Parts Required Qty
Panel (K) 2
Panel (L) 2
A
c
B
D
IE
F
c
c
c
c
K
L
H
G
Page 5 of 16
X2
X2

STEP 2
Parts Required Qty
Panel (A) 1
Panel (B) 1
Panel (C) 1
Panel (J) 2
Parts Required Qty
Panel (A) 1
Panel (B) 1
Panel (F) 2
22 x
d
STEP 3
j
d
B
d
d
A
J
C
d
d
B
A
FF
i
i
i
j
j
jj
i
j
j
i
Page 6 of 16
8 x
i
4 x
j

STEP 4
STEP 5
g
f
f
2 x
a
E
a
m
E
F
H
H
Parts Required Qty
Panel (E) 1
Panel (H) 1
Parts Required Qty
Panel (F) 1
Page 7 of 16
m
1 x
a
m
a
m

STEP 6
STEP 7
a
1 x
a
m
Page 8 of 16
F
H
E
m
1 x
a
m
a
m
F
H
E
G
Parts Required Qty
Panel (G) 1

STEP 9
Panel (I) 1
Parts Required Qty
Panel (D) 1
STEP 8
A
G
Parts Required Qty
Panel (A) 1
2 x
h
hH
F
h
Page 9 of 16
I
D
E

STEP 10
STEP 11
h
Parts Required Qty
Panel (B) 1
h
2 x
h
4 x
h
A
G
H
F
E
D
I
A
G
H
B
F
DI
E
Page 10 of 16
h
h
5 x
g
g

STEP 12
STEP 13
Parts Required Qty
Panel (C) 1
4 x
h
6 x
h
A
B
Page 11 of 16
h
D
E
F
G
A
BD
FG
C
H
h
h
h

STEP 14
STEP 15
Parts Required Qty
Panel (Z) 2
8 x
b
K
Page 12 of 16
M
L
b
X2
Panel (M) 2
Panel (L) 2
Parts Required Qty
Panel (K) 2
KM
L
Z
X2

STEP 16
STEP 17
K
Page 13 of 16
M
L
h
X2
Parts Required Qty
Panel (J) 2
Z
J
h
4 x
h
4 x
k
8 x
f
L
Z
J
L
f
f
k
k
f
k

STEP 17
STEP 18
Page 14 of 16
K
M
L
e
X2
ZJ
4 x
e
l
2 x
l

STEP 19
Page 15 of 16
Put the screw in
the top panel hole
of your furniture
Make a hole in
the wall and put
the wall plug in
Put the screw in
the wall plug hole
o
o
f
NOTE : Wall fixing are not supplied with this product
as different devices (such as Rawl plugs on brick
work).You must use fixing devices suitable for the
type of wall you intend to mount this product to.
Please ensure that the head of any screw used has
a diameter greater that the diameter of the mounting
hole on the product and than the fixing is safe and
secure before use.
The straps and screws to fix the strap on to
the furniture are provided only.
n
nWall Plug
1 x
oSafety strap (L-200mm)
1 x
fCsk Screw (M3.5x15mm)
1 x

Your LANCASTER CONSOLE HALL TABLE is now completely assembled
Page 16 of 16