GFW KENDAL MULTI UNIT User manual

Thank you for purchasing the KENDAL MULTI UNIT. Please read the instructions carefully to ensure
safe operation of the product.
Size: 788 x 389 x 775mm
PLEASE READ this sheet prior to assembly to familiarise yourself with the various stages of construction.
Carefully open the pack supplied and check the contents against the parts and fittings check list. Do not
destroy any of the packaging until you are certain that you have all the necessary parts for the assembly.
CAUTION: There are small components used in the construction of this unit. These loose items should be
kept away from young children whilst assembling your unit to avoid the danger of choking hazards.
Tools Required
V2 2022.02
Page 1of 20
3.5m/12'x 2
Person Required Approximate
Assembly Time
1.5 hours
KENDAL MULTI UNIT
ASSEMBLY INSTRUCTIONS

V2 2022.02
Page 2of 20
IMPORTANT - READ CAREFULLY - RETAIN THESE INSTRUCTIONS FOR
FUTURE REFERENCE.
INFORMATION
�Due to the size of this product we recommend that it is assembled in the room intended for use
�When you are ready to start, make sure that you have the right tools, plenty of space and a clean, dry area for
assembly.
�Unwrap all packaging materials and place the components on top of the carton box or on a clean oor to
prevent it from scratching.
�Check the pack and make sure you have all the parts listed.
�Ensure that this product is fully assembled as illustrated before use.
�Check all screws or bolts are tightened and inspect regularly
�This product should only be used on rm, level ground.
�Keep small parts out of reach of children.
�Make sure the legs remain in contact with the ground.
�Tools not included.
WARNINGS
�DO NOT use power tools to construct this product.
�DO NOT over tighten screws or bolts.
�DO NOT use this product if parts are missing, damaged or worn.
�DO NOT sit or stand on the product.
�It is essential that this unit is xed to the wall with the brackets provided for safety reasons. NB wall xings are
not included. Please source suitable xings for your wall type. If in doubt please consult a qualied
tradesperson.
�WARNING : Always ensure the area to be drilled is free from hidden electrical wires, water or gas pipes
CARE INFORMATION
�Never use scourers, abrasives or chemical cleaners.
�To clean wipe with a sponge and warm soapy water. Do not use solvent based cleaners or detergents as they
can bleach or damage the product.

V2 2022.02
Page 3of 20
Please check the pack contents before assembling the product. If any components are missing,
please contact your retailer. The fittings pack contains small items that should be kept away from
small children.
CODE QTYPART NAME
A
B
C
1
D
Top Panel
Bottom Panel
Side Panel - L
Side Panel - R
Parts
CODE
E
J
K
L
Drawer Front
Front Prole
Door
30 x 350 x 740mm
DIMENSION
30 x 350 x 740mm
30 x 386 x 788mm
15 x 350 x 718mm
QTY
15 x 350 x 645mm
DIMENSION
15 x 96 x 779mm
15 x 370 x 637mm
15 x 210 x 370mm
PART NAME
Drawer Side - L 15 x 140 x 296mm
1
1
1
1
1
1
3
3
Drawer Side - R 15 x 140 x 296mm 3
Center Panel
F15 x 348 x 351mm
1 Drawer Back 15 x 140 x 296mm 3
Adjustable Shelf
GDrawer Bottom 3 x 290 x 305mm
3
H
15 x 80 x 351mm
1
Back Panel 3 x 343 x 744mm 2
Support Bar
I
15 x 80 x 718mm
1
Bottom Support
M
N
A
B
C
D
E
F
G
HIJ
K
K
K
L
L
L
M
N

Fixings (to scale)
V2 2022.02
Page 4of 20
14x
M3.5 x 15mm
H
CSK
Screw
2x
M6.3 x 40mm
A
Unitar
Screw
20x
EU 24
C
Minix
Bolt
36x
Dia. 8 x 30mm
D
Wooden
Dowel
10x
#10 x 16mm
F
Tapping
Screw
2x
M4 x 22mm
E
Handle
Screw
6x
#6 x 16mm
G
Tapping
Screw
12x
M4 x 38mm
B
CSK
Screw
12x
M6 x 8mm
I
Euro
Screw
4x
L
Nail Leg
16x
K
Nail Pin
4x
J
Shelf Support

Fixings (not to scale)
V2 2022.02
Page 5of 20
20x
Dia. 15 x 12mm
M
Minix Cam
1x
2mm
O
L-Bracket
2x
N
Hinges (5/8")
1x
L-145/H-96mm
P
Handle
3x
H-64mm
Q
Pocket Handle
2x
D-16mm
R
Flat Washer
2x
1.2x15x32x75mm
S
L-Mounting
Bracket
1x
M4
T
Allen Key
3 set x
12" (300mm)
U
Drawer Slide
3 set x
12" (300mm)
V
Drawer Slide

V2 2022.02
Page 6of 20
Layout Parts on Soft Surface
C
J
I
G
D
K
L
M
N
H
E
B
A
F
K
L
M
N
K
L
M
N

V2 2022.02
Page 7of 20
STEP 1
TOP
BOTTOM
12 x3 x
IU CJ
4 x 8 x
PLEASE ENSURE TO FIX THE SCREWS AS PER ABOVE POINTED HOLES
INSTRUCTION TO AVOID DISTORTION OF OVERALL LOOK OF PRODUCTS
SECOND HOLE
BACK
FRONT
TOP
TOP
BOTTOM
A
B
E
E
I

V2 2022.02
Page 8of 20
STEP 2
STEP 3
3 x
D
2 x
A
2
2
2 x
D
1
1
D
D
E
E
G
H

V2 2022.02
Page 9of 20
STEP 4
STEP 5
9 x
D
M
6 x
A
B
D
D
G
G
H
1
2
2
1

V2 2022.02
Page 10 of 20
STEP 6
M
2 x
4 x
D
STEP 7
A
B
D
D
I
2
1
2
1