GFW MADRID WOODEN OTTOMAN BED 3FT User manual

COMO OTTOMAN BED 3FT
ASSEMBLY INSTRUCTIONS
Thank you for purchasing the COMO OTTOMAN BED 3FT. Please read
the instructions carefully to ensure safe operation of the product.
Size: 3FT L 2016 X W 1032 X H 1005
PLEASE READ this sheet prior to assembly to familiarise yourself with the various stages of construction.
Carefully open the pack supplied and check the contents against the parts and fittings check list. Do not destroy any of
the packaging until you are certain that you have all the necessary parts for the assembly.
CAUTION: There are small components used in the construction of this unit. These loose items should be kept away
form young children whilst assembling your unit to avoid the danger of choking hazards.
Tools Required
X 2 1Hour
Set Up
V2 01/20
Page 1 of 20

IMPORTANT - READ CAREFULLY - RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE.
COMO OTTOMAN BED 3FT
ASSEMBLY INSTRUCTIONS
INFORMATION
•This product is intended for a maximum person's weight of 110kg. Do
not exceed this weight.
•Due to the size of this product we recommend that it is assembled in the room
intended for use.
•When you are ready to start, make sure that you have the right tools, plenty of
space and a clean, dry area for assembly.
•Unwrap all packaging materials and place the components on top of the carton
box or on a clean floor to prevent it from scratching.
•Check the pack and make sure you have all the parts listed.
•Ensure that this product is fully assembled and secured as illustrated before use.
•Check all screws or bolts are tightened and inspect regularly.
•This product should only be used on firm, level ground.
•Please dismantle for transportation.
•Tools not included.
WARNING
•Keep small parts out of reach of children.
•Make sure the legs remain in contact with the ground.
•DO NOT use power tools to construct this product.
•DO NOT tighten screws until fully assembled.
•DO NOT over tighten screws or bolts.
•DO NOT use this product if parts are missing, damaged or worn.
•DO NOT stand on the product.
•This bed uses a pressured mechanism, always use caution when operating.
•DO NOT remain on the bed whilst the lifting mechanism is in use.
•Only use the storage compartment when the frame is fully raised in the up
position.
•Please pay particular attention when children or animals are present to ensure
that no accidental entrapment occurs whilst operating this product.
•Keep hand and fingers clear of the mechanism when opening and closing the
bed for use.
•Incorrect installation could lead to injury, take care following instruction.
•Take care when adjusting positions to avoid trapping of body parts.
CARE INFORMATION
•Never use scourers, abrasives or chemical cleaners.
•To clean wipe with a sponge and warm soapy water. Do not use solvent based
cleaners or detergents as they can bleach or damage the product.
V2 01/20
Page 2 of 20

Please check the pack contents before assembling the product. If any components are missing, please
contact your retailer. The fittings pack contains small items that should be kept away from small children.
(P9)
(P8)
(P12)
(P11)
(P8)
(P9)
(P3)
(P2)
(P1)
(P10)
(P6)
(P7)
(P5)
(P4)
COMO OTTOMAN BED 3FT
ASSEMBLY INSTRUCTIONS
(P13)
V2 01/20
Page 3 of 20

Parts
HEADBOARD
1PC
Carton No: 1
P1
FOOTBOARD
1PC
Carton No: 2
P2
SIDE RAIL
2PCS
Carton No: 2
P3
FRONT TUBE
1PC
Carton No: 3
P4
BACK TUBE
1PC
Carton No: 3
P5
CENTRE TUBE
1PC
Carton No: 3
P6
SIDE TUBE
2PCS
Carton No: 3
P7
HINGE
2PCS
Carton No: 3
P8 P9
PISTON
2PCS
Carton No: 3
LEFT RIGHT
COMO OTTOMAN BED 3FT
ASSEMBLY INSTRUCTIONS
V2 01/20
Page 4 of 20

Parts
MATTRESS STOPPER
2PCS
Carton No: 2
P10 P11
HOLDING BLOCK
1PC
Carton No: 2
P12
HOLDING TUBE
2PCS
Carton No: 3
P13
WOODEN SLAT
13PCS
Carton No: 3
P14
NON-WOVEN FABRIC
1PC
Carton No: 2
COMO OTTOMAN BED 3FT
ASSEMBLY INSTRUCTIONS
V2 01/20
Page 5 of 20

10 20 30 40 50 60 70 80 90 100 110 120
Fixings (to scale)
Ref Dimensions Qty
H1 JCBC SCREW M6 X 80MM 8
H2 JCBC SCREW M6 X 45MM 6
H3 JCBC SCREW M6 X 15MM 34
H4 BARREL NUT M6 X 16MM 8
H5 DOWEL M10 X 30MM 16
H11 WOOD BUTTON 8MM 8
(Not to scale)
Ref Dimensions Qty
H6 M4 ALLEN KEY 1
CAUTION: There are many small components used in the construction of this product. Please keep
these components away from young children whilst assembling this product.
If you keep the fittings in a bowl during assembly you will be less likely to lose them
H8 CORNER BRACKET 4
H9 PLASTIC END CAP 26
H10 BELT 1
COMO OTTOMAN BED 3FT
ASSEMBLY INSTRUCTIONS
V2 01/20
Page 6 of 20

Turn to page 12 for fitting the hinges
12
R
The pistons used in the construction of this product are extremely strong and cannot be operated by
hand when not fitted to the ottoman hinges. All pistons are tested in the factory for correct pressure and
operation before use.
Initially it might appear that the pistons are very stiff when opening and closing the ottoman
frame, THIS IS NORMAL.
After operating the ottoman a few times, the movement of the pistons and the opening and closing of the
ottoman will become easier.
L
COMO OTTOMAN BED 3FT
ASSEMBLY INSTRUCTIONS
V2 01/20
Page 7 of 20

Hints and Tips
To operate the ottoman, always use 2 hands at arm's length and only where illustration on this product.
You must ensure the mattress is on the bed frame before lifting the mechanism. Failure to do so may
result in injury.
To ensure your safely please do not stand too close in case the frame bounces up. The weight of the
mattress loaded on the frame will keep the frame in a lower position until it is pulled upwards by the user.
Do not attempt to move the bed whilst the frame is in the upright position
If removing the mattress, make sure the frame is secured so it does not flip open. When lifting the bed
frame, remove pillows and covers.
PLEASE NOTE - It takes a lot of force to make the initial movement of the ottoman - THIS IS A DESIGN
FEATURE OF THE PRODUCT SO THAT IT DOES NOT FALL SHUT - and the nearer to being closed
the ottoman is, the easier it is to move. When the ottoman is almost shut, it will close completely under
its own weight.
When lowering the slat unit for the first time, take care to make sure it does not rub unevenly on the
inside face of the Side Rail. If it does, the bed has been assembled slightly out of square. This can be
rectified by moving the Footboard of the bed slightly to the left or right whilst leaving the headboard of
the bed frame stationary.
Tip for difficulty with compression:
If you are experiencing difficulty with the initial compression try fitting one piston at a time (following the
Assembly Instructions) then press down on the side of the frame with the piston fitted - this acts like a big
lever (The weight of the mattress can be used to supplement the load exerted). Effectively you are
doubling the amount of force applied, because you have halved the resistance offered by the pistons. It
can take slightly more effort than you might feel comfortable applying to the bed frame at first.
COMO OTTOMAN BED 3FT
ASSEMBLY INSTRUCTIONS
V2 01/20
Page 8 of 20

Do not attempt to move the bed whilst the frame is in the upright position.
COMO OTTOMAN BED 3FT
ASSEMBLY INSTRUCTIONS
V2 01/20
Page 9 of 20

2 people are required to fit the frame safety.
COMO OTTOMAN BED 3FT
ASSEMBLY INSTRUCTIONS
V2 01/20
Page 10 of 20