Gigaset Gigaset DA710 User manual

Gigaset DA710 / en / A30350-M213-A601-3-UZ19 / overview.fm / 26.04.2016
en fr fa ar 1
1110-01
Overview Gigaset DA710
Display and keys
1 Adjustable display (Changing the language £page 11)
2 Control key
3Shiftkey
4Menukey
5 Redial/pause key
6Recallkey
7Mutekey
8Directdialkey
9 Insert strip for writing the assignment of direct dial keys
10 Star key, selecting/deselecting the ring tone (press and hold)
11 Hash key, selecting/deselecting the key lock (press and hold)
12 Hands-free/headset key
13 Keys for setting the volume of the handset, headset, speaker and
ring tone
14 Microphone for hands-free
LED
AHands-free/headset key
¤flashes on incoming call
¤lights up when the call is transferred to the speaker or headset
¤flashes when you hang up the handset, either if a new call or a new
message has been received (settings £page 11)
1
3
6
4
13
7
9
8
12
5
2
14
10
11

Gigaset DA710 / en / A30350-M213-A601-3-UZ19 / overview.fm / 26.04.2016
2en fr fa ar
1110-01
Connecting the telephone
4
1
6
2
5
3
¤Connect the telephone connector (1) to the main telephone socket. Use the telephone
cable supplied.
You may need a phone adapter depending on your country. This is provided in most
cases.
Wall mounting
¤Drill two holes into the wall at a
distance of 12.4 cm and fix two
screws.
¤Lift out the handset bracket (6)
with a screwdriver and clip it into
the handset cradle (7).
¤Hang the telephone on the pro-
jecting screw heads.
¤Guide the cable through the cable channel: upwards for oper-
ating the phone on the table (2); downwards when mounting
the telephone on the wall (3).
¤Connect the handset to the telephone using the coiled cable (4).
7
Connecting the headset
¤Plug in (5) a headset using an RJ9 plug, e.g. a Gigaset ZX410.
Notes
uFirst use
1. Lift the handset for 5 seconds and place it back in the cradle.
2. Lift the handset again. You will hear the free tone and the device is now ready to be used.
The phone is connected to the power source via the phone line. In case of a power cut (e.g. if the PBX is switched off at night), the above men-
tioned steps need to be repeated. Phonebook entries and speed dialling destinations are stored indefinitely.
uThe device is designed to be used as a single-line system (on the main extension or a telephone system).
It cannot be operated as a second phone on a line splitter.
uOperation on a PBX or router
The private branch exchange (PBX) or the router must supply the phone with continuous DC voltage, even when ringing. If this is not the case,
the phone may switch off briefly when ringing. As a result, saved information may be lost. Refer to the operating manual for your PBX or router
for information in this regard or contact the manufacturer.

Gigaset DA710 / en / A30350-M213-A601-3-UZ19 / DA710IVZ.fm / 26.04.2016
en fr fa ar 3
1110-01
Table of contents
Overview Gigaset DA710 . . . . . . . . . . . . . . . . . . . . 1
Connecting the telephone . . . . . . . . . . . . . . . . . . 2
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Setting up the telephone for use . . . . . . . . . . . . . 4
Operating the telephone . . . . . . . . . . . . . . . . . . . . . 4
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Control key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Writing and editing text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Phonebook, call list and redial list . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Menu tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Telephoning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Making a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Incoming calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Using open listening / hands-free / headset . . . . . . . . . . . . . . . . 8
Settings during a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Using the phonebook, lists and direct
dial keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Phonebook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Call list (CLIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Last number redial list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Direct dial keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Adjusting the telephone . . . . . . . . . . . . . . . . . . . 11
Basic settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Setting the volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Setting the ringer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Security settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Locking the telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Emergency calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Direct calling (baby call) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Blocking numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Network services . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Caller display (CLIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Call Divert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Other network services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Recall key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Setting up of dialling code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Operation on a PABX. . . . . . . . . . . . . . . . . . . . . . . 14
Special functions/Recall key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Changing the dialling mode/flash time . . . . . . . . . . . . . . . . . . . . 14
Setting dialling prefixes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Other settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Predefined key combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Standard characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Contact with liquid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Questions and answers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Authorisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Gigaset DA710 / en / A30350-M213-A601-3-UZ19 / using.fm / 26.04.2016
4en fr fa ar
1110-01
Safety precautions
When installing, connecting and operating the telephone, always
observe the following precautions:
uOnly use the jacks and leads supplied.
uOnly connect the connecting lead to the intended socket.
uOnly connect the approved accessories, such as the Gigaset ZX410
headset for example.
Your Gigaset DA710 has been tested and approved with the Gigaset
ZX410 headset.
uOther headsets may only function to a limited extent or not at all. Be
sure to reduce the volume of the Gigaset DA710 when connecting
another headset. As a headset from another manufacturer may emit
a harmful and loud acoustic signal due to alignment differences.
uLay the connecting lead where it will not cause accidents.
uPosition the telephone on a non-slip surface.
uFor your safety and protection,the telephone may not be used in the
bath or shower rooms (wet locations). The telephone is not splash
proof.
uNever expose the telephone to sources of heat, direct sunlight or
other electrical devices.
uProtect your telephone from moisture, dust, corrosive liquids and
vapours.
uNever open up the telephone yourself.
uDo not touch the plug contact with pointed or metallic objects.
uDo not carry the telephone by the leads.
uIf you give your Gigaset DA710 to someone else, make sure you also
give them the operating manual. Your Gigaset DA710 has a perma-
nent memory, so you may want to delete any stored numbers before
passing it on.
Setting up the telephone for use
Recommended installation of telephone:
uDo not expose the telephone to direct sunlight or other sources of
heat.
uOperate at temperatures of between + 5° C and + 40° C.
uMaintain a distance of at least one metre between the telephone
and radio equipment, e.g. radio telephones, radio paging equip-
ment or TV sets. Otherwise telephone communication could be
impaired.
uDo not install the telephone in dusty rooms as this can limit the ser-
vice life of the telephone.
uFurniture lacquer and polish can be adversely affected by contact
with parts of the unit (e.g. feet).
Operating the telephone
The keypad and the display are available to operate your Gigaset DA710.
In addition, the display menu together with the control key provides
access to the configuration and use of the many functions of the tele-
phone. All usage possibilities are described in the handbook.
Display
In stand-by mode, the time, date and calendar week are displayed. You
can set the date and time and the format in which it is displayed
(£page 11). Symbols on the display also provide information regarding
the status of your telephone.
Display symbols
fFlashes for a new call in the call list if the caller's number
transmission (CLIP) is active (£page 13)
ZPhonebook open
hShift key pressed
iKey lock activated
kRing tone switched off
lFlashes on incoming VIP call
Is indicated if at least one entry with activated VIP mode is
present in the phonebook (£page 9).
mMute mode activated
nHeadset connected
Note
Some of your telephone's functions may only be available without
restriction if they are supported by your and the caller's network pro-
vider, e. g. functions for which information on the caller's telephone
number is required.
This applies for the following functions, for example:
uDisplaying the number of an incoming call (£page 8)
uIndicating a caller with VIP melody (£page 8)
uCall list (£page 10)
uCall forwarding and other network services (£page 13)
nlm
14:00
23.08.2011 CW34
Toolbar
Time (24h format)
Date / Calendar week

Gigaset DA710 / en / A30350-M213-A601-3-UZ19 / using.fm / 26.04.2016
en fr fa ar 5
1110-01
Control key
The telephone's functions are activated and the menu is navigated
using the control key. The functions offered depend on the operating sit-
uation.
Writing and editing text
~Enter text using the keypad.
Multiple letters and numbers are assigned to each key between
and Oand Q, *and #. The entry of a specific charac-
ter is carried out by pressing the corresponding key multiple times.
You will find a table of applicable characters in the Appendix £page 15.
To switch between capital letters (ABC), lower case (abc) and numbers
(123), press the shift key L until the desired figure is briefly displayed
on the bottom right. This mode is not available in lines for telephone
number entry.
Moving the cursor
t s Press the control key up/downwards in order to move the
cursor to the left/right in the text.
Deleting/correcting characters
XPress the left-hand side uof the control key. The cha-
racter to the left of the cursor is deleted. Press and hold
down to delete the whole line.
Menu
The functions of your telephone are offered to you via a menu that con-
sists of several levels.
¤Press the Mkey to open the menu.
The menu functions and submenu functions where necessary are dis-
played in list form.
¤Scroll with the control key qto the required function and press
the right-hand side of the control key v, ([) to confirm your
selection.
¤Press u(X) in order to return to the previous menu level.
¤Press the Mkey to return to the start menu.
Description of the menu selection steps
The steps to select a menu function are set out in these operating
instructions as follows:
M¢Phone setup ¢Language
This is accessed as follows:
¤Open the menu using the Mkey.
¤Using the control key q, select the entry Phone setup and press
the right-hand side of the control key v, ([).
¤Using the control key q, select the entry Language and press the
right-hand side of the control key v, ([).
Phonebook, call list and redial list
Phonebook, call list and redial list can be opened using the menu or
keys.
Using the menu
¤Press the Mkey to open the menu.
¤Select Call list (CLIP) or Phonebook or Redial in order to open the
desired list.
Using keys
YOpen the call list using the control key t.
ZOpen the phonebook using the control key s.
IOpen the redial list.
The first list entry will be displayed in each case.
¤Scroll with the control key qto the desired entry and press the
right-hand side of the control key v, ([) to open the context
menu.
In standby:
tYOpen the call list
sZOpen phonebook
t
s
In menus and lists:
Scrolls one entry upwards/downwards.
Hold down: Scrolls the list fast upwards/downwards.
While editing names and numbers:
Moves the cursor to the left/right.
Hold down: Moves the cursor fast to the left/right.
While pressing the direct dial key:
Displays long phone numbers completely.
uIn menus, lists and with direct dial keys:
Exits the menu, list or direct dial key.
While changing settings:
Terminates the action without changing the setting.
While editing names and numbers:
Deletes the character to the left of the cursor.
Hold down: Deletes the line.
If the entry is empty: Exits the editing mode.
vPhone number entered or direct dial key pressed:
Dials the phone number.
In menus and lists:
Opens the submenu/context menu.
While editing entries/changing settings:
Saves the edits or activates the selected settings.
W
TU
V
Note
To exit the menu without saving any previous entries simply lift and
then hang up the handset. After a short time the display will then
once again show the standby mode.

Gigaset DA710 / en / A30350-M213-A601-3-UZ19 / using.fm / 26.04.2016
6en fr fa ar
1110-01
Menu tree
The complete menu tree of the display menu is depicted below.
Call list (CLIP) Entry 1- 50 Call back £page 7
Save number £page 10
Delete entry £page 10
Delete all £page 10
Phonebook New entry £page 9
Entry 1-100 Dial entry £page 7
Edit entry £page 9
New entry £page 9
Delete entry £page 9
Delete all £page 9
Security Change PIN £page 12
Key lock £page 12
Emergency £page 13
Direct call £page 12
Call block £page 13
Phone setup Language £page 11
Date/time £page 11
Dial mode £page 14
Flash time £page 14
PABX code £page 14
Date/Time format £page 11
Area code £page 14
Speaker LED £page 11
Audio setup Ring tones £page 11
VIP Melody £page 12
Handset Volume £page 11
Speaker Volume £page 11
Headset Volume £page 11
Mute mode £page 11
Ringer mode £page 12
CLASS Call Divert £page 13
CW Signal £page 13
Withhold number £page 14
Hotline £page 14
Ringback £page 14
Auto recall £page 14
Phonemail £page 14
Redial Entry 1- 5 Dial entry £page 7
Save number £page 10
Delete entry £page 10
Delete all £page 10

Gigaset DA710 / en / A30350-M213-A601-3-UZ19 / telephony.fm / 26.04.2016
en fr fa ar 7
1110-01
Telephoning
In addition to the headset, you can also call using the speaker (hands-
free function) or using a headset connected to the telephone
(£page 8). In the following instructions, the symbol calso always
stands for A.
Making a call
Entering the telephone number using the keypad
~c Dial the number, lift the handset.
or
c~ Lift the handset, dial the number.
Instead of lifting the handset:
APress the hands-free/headset key to make a call via the
speaker or the connected headset.
You can switch over at any time during the conversation.
Making a correction when entering the telephone number (only
possible if the handset is in its cradle):
XPress the control key uto delete a digit entered in error
to the left of the cursor.
Dialling from the phonebook
If you have already saved numbers in your phonebook (£page 9), you
can make a call directly from the phonebook.
M¢Phonebook
or
ZOpen the phonebook using the control key s.
Searching an entry
qSelect an entry.
Hold down the top or bottom of the key to scroll fast in the
list.
or
~Enter letters (£page 5). The first entry starting with this
letter is displayed.
Dialling numbers
cLift the handset.
or
[Open context menu.
qSelect Dial entry and initiate the call using the speaker
with [. Lift the handset to make the call using the hand-
set.
Dialling from the call list
The call list contains the numbers of the last 50 incoming and outgoing
calls. Prerequisite: Telephone number display is possible for incoming
calls (£page 13).
Multiple calls from one number are only displayed once (with the infor-
mation of the last call). If the number is saved to the phonebook or to the
direct dial keys, the accompanying name is also displayed if present.
M¢Call list (CLIP)
or
YOpen the call list using the control key t.
Dialling numbers
qSelect the number or name.
cLift the handset.
or
qSelect the entry and open context menu with [.
qSelect Call back and initiate the call using the speaker with
[. Lift the handset to make the call using the handset.
Last number redial
The last five numbers dialled are automatically saved (each a max. of
32 digits).
Dialling the last saved number:
I c Press the redial key, lift the handset.
or
c I Lift the handset, press the redial key.
Dialling one of the last five numbers saved:
M¢Redial
or
IPress the redial key.
Dialling numbers
qSelect the number.
cLift the handset.
or
qSelect the entry and open context menu with [.
qSelect Dial entry and initiate the call using the speaker
with [. Lift the handset to make the call using the hand-
set.
Note
You can also first lift the handset before opening the phonebook.
Note
You can also first lift the handset before opening the call list.
Note
You can also first lift the handset before opening the redial list.

Gigaset DA710 / en / A30350-M213-A601-3-UZ19 / telephony.fm / 26.04.2016
8en fr fa ar
1110-01
Dialling a number using the direct dial key
You can save 16 numbers to 8 direct dial keys and dial directly (two num-
bers can be allocated to each direct dial key, each with a max. of
32 digits). Use the shift key Lto access the key's second storage area.
The display symbol h indicates that the shift function is active.
Saving and editing the direct dial keys is possible using the context
menu of the direct dial key (£page 10), from the phonebook, the call
list and the redial list.
c Lift the handset, press the direct dial key.
or
BcPress the direct dial key, lift the handset.
or
BPress the direct dial key and open the context menu with
[.
[Initiate the call over the speaker using the control key. Lift
the handset to make the call using the handset.
You can extend the selected number by entering additional digits.
Incoming calls
Incoming calls are indicated by the ring tone and in the display.
For number displays (£page 13), the number is visible in the display
and the fsymbol flashes. This symbol disappears when you answer the
call or (if you don't answer) by calling up the call list.
The name is also displayed for callers who are stored in the phonebook
or on the direct dial keys with names.
If the VIP mode is activated (£page 12) the VIP symbol flashes in the
display and the VIP ring tone signals the call.
Accepting a call
cLift the handset.
or
APress the hands-free key to accept the call via the speaker
or the connected headset.
Call waiting
If the Call waiting service is activated (£page 13), an incoming call is
indicated during the conversation. You will hear the call waiting tone.
The display shows the caller number if the number can be displayed, and
the name if it is saved in the phonebook (£page 9).
HPress the callback key to accept the call. The first caller
hears a wait melody.
HPress the callback key again to end the second call and to
return to the first call.
Using open listening / hands-free / headset
Switching open listening on/off
The persons present in the room can listen to the call over the speaker.
During the call using the handset:
APress the hands-free key to switch open listening on or off.
When the speaker is switched on and the handset is picked up, open lis-
tening is switched on. In this case, the hands-free microphone is
switched off.
When the speaker is switched on and the handset is in the cradle, hands-
free via the hands-free microphone is switched on.
Switching from open listening to hands-free:
A & Replace the handset whilst pressing the hands-free key.
Switching the hands-free on/off
You can also make a call via the microphone with the handset in the cra-
dle. The optimum distance from the microphone is approx. 50 cm.
Switching on hands-free during a call
A & Replace the handset whilst pressing the hands-free key.
Switching on hands-free prior to dialling
AHands-free key, wait for dial tone.
Switching off hands-free
cLift the handset during the call. The call is transferred to
the handset.
Ending a call
APress the hands-free key during a call over the speaker.
Using a headset
Connect the headset (£page 2). You can then make a call over the
headset whilst the handset is in the cradle. (Please note the safety pre-
cautions £page 4.)
AThe telephone is operated using the hands-free/headset
key in the same way as for the hands-free function (see
above).
Once the headset is connected this is indicated in the display with the n
symbol.
Note
Hands-free and open listening are not possible if a headset is con-
nected.

Gigaset DA710 / en / A30350-M213-A601-3-UZ19 / telephony.fm / 26.04.2016
en fr fa ar 9
1110-01
Settings during a call
The settings described below can also be changed in the menu
(£page 11).
Setting the handset/headset volume
There are three adjustable levels.
E/ DSet the volume using the volume up/volume down keys.
The set volume is shown in the display.
Setting the speaker
There are seven adjustable levels.
E/ DSet the volume using the volume up/volume down keys.
The set volume is shown in the display.
Mute
You can switch off the microphone or handset and microphone during a
call according to the setting of the mute function (£page 11):
CPress the mute key to switch the mute function on or off.
During muting of the microphone, a melody can be played.
Once the telephone has been muted this is indicated in the display with
the msymbol.
Ringer and volume
Whilst the telephone is ringing, the volume and ringer can be changed.
E/ DSet the ringer volume with the volume up/volume down
keys (5 levels, 0=silent).
Q.. OSelect ringer with the numeric keys (10 different).
Using the phonebook, lists and direct
dial keys
The following options are available on your telephone for storing your
contacts and the incoming and outgoing calls:
uPhonebook with max. 100 entries
uCall list with the last 50 incoming calls
uRedial list with the last 5 outgoing calls
uDirect dial keys for storing 16 important numbers
Phonebook
Your Gigaset DA710 contains a phonebook in which you can save up to
100 entries, each with a maximum of 32 digits for numbers and 16 char-
acters for names.
You can make a call (£page 7), add new entries and manage and mod-
ify entries (£page 9) using the Phonebook.
You can manually enter numbers and names or transfer them from the
call list (£page 10). You can also allocate VIP mode to a number.
The Zsymbol is indicated in the display if the phonebook has been
opened. In addition, the phonebook entry number is also indicated in
the display (01.. 99, 00 is displayed for 100).
Opening phonebook
In standby:
ZPress the control key s.
or
M¢Phonebook
Searching an entry
qSelect an entry.
Hold down the the top or botton of the key to scroll fast in
the list.
or
~Enter letters (£page 5). The first entry starting with this
letter is displayed.
Saving numbers
M¢Phonebook
The first list entry is displayed.
tSelect New entry and confirm with [.
~Enter number and confirm with [.
~Enter name and confirm with [.
The notice Save to PBK? appears in the display.
Either: save in phonebook
[Confirm the saving of the entry in the Phonebook.
qSelect VIP mode (On / Off) and confirm with [.
Or: save to a direct dial key
B/ L B
Press the desired direct dial key.
The notice Saved appears in the display.
Delete entry / Delete all
M¢Phonebook
The first list entry is displayed.
qSelect the entry and open context menu with [.
qSelect Delete entry or Delete all and confirm with [.
[Press the control key to confirm the action.
Edit entry
M¢Phonebook
The first list entry is displayed.
qSelect the entry and open context menu with [.
qSelect Edit entry and confirm with [.
~Change number and confirm with [.
~Change name and confirm with [.
The notice Save to PBK? appears in the display.
Note
If you press *, the entry is set as a VIP entry or the setting is dele-
ted.
Note
You can save an entry first in the phonebook and then to a direct dial
key.

Gigaset DA710 / en / A30350-M213-A601-3-UZ19 / telephony.fm / 26.04.2016
10 en fr fa ar
1110-01
Either: save in phonebook
[Confirm the saving of the entry in the Phonebook.
qSelect VIP mode (On / Off) and confirm with [.
Or: save to a direct dial key
B/ L B
Press the desired direct dial key.
The notice Saved appears in the display.
Call list (CLIP)
Incoming calls are saved if the number is transmitted (£page 13). Up to
50 calls are saved. If the number is the same, only the last incoming call
is saved. The oldest call is automatically deleted when there are more
than 50 calls. If the caller is saved to the phonebook or to a direct dial key,
the name is also displayed.
You can use the call list for the following functions:
¤Calling a number from the list (£page 7).
¤Saving in the phonebook or to direct dial keys.
Opening the call list
Open the call list in standby mode:
YPress the control key t.
or
M¢Call list (CLIP)
Transferring a number from the call list to the phonebook/
direct dial key
YOpen the call list.
qSelect the entry and open context menu with [.
qSelect Save number and confirm with [.
~Change number (if required) and confirm with [.
~Enter name and confirm with [.
While editing numbers and names, move the cursor with q.
Either: save in phonebook
[Confirm the saving of the entry in the Phonebook.
qSelect VIP mode (On / Off) and confirm with [.
Or: save to a direct dial key
B/ L B
Press the desired direct dial key.
The notice Saved appears in the display.
Delete entry / Delete all
YOpen the call list.
qSelect the entry and open context menu with [.
qSelect Delete entry or Delete all and confirm with [.
[Press the control key to confirm the action.
Last number redial list
The last five numbers called are automatically saved (each a max. of
32 digits).
Opening the last number redial list
IPress the redial key.
or
M¢Redial
Transferring a number from the redial list to the phonebook/
direct dial key
IOpen the last number redial list.
qSelect the entry and open context menu with [.
qSelect Save number and confirm with [.
~Change number (if required) and confirm with [.
~Enter name and confirm with [.
While editing numbers and names, move the cursor with q.
Either: save in phonebook
[Confirm the saving of the entry in the Phonebook.
qSelect VIP mode (On / Off) and confirm with [.
Or: save to a direct dial key
B/ L B
Press the desired direct dial key.
The notice Saved appears in the display.
Delete entry / Delete all
IOpen the last number redial list.
qSelect the entry and open context menu with [.
qSelect Delete entry or Delete all and confirm with [.
[Press the control key to confirm the action.
Direct dial keys
You can save up to 16 numbers on direct dial keys. Use the shift key L
to access the keys’ second storage area. The display symbol h indicates
that the shift function is active.
You can also assign direct dial keys from the entries in the phonebook,
in the call list or the redial list.
They can also be used as function keys e. g. for call forwarding. Your net-
work provider will notify you of the services and functions offered and
the corresponding key sequences. The menu offers you additional
optional settings for network services (£page 13).
Saving numbers / Changing the allocation
B/ L B
Press the direct dial key that you want to assign with a
number or the entry of which is to be changed.
Empty is displayed when the storage is empty.
If the key is already assigned you will see the saved number. For long
numbers (more than 16 digits) switch between the display of digits 1-16
and 17-32 with the control key q.
New entry
[Switch to the entry mode with [.
Changing the allocation
[Open the context menu with [.
qSelect Edit entry and confirm with [.
Enter/change number and name
~Enter/change number and confirm with [.
~Enter/change name and confirm with [.