Girard Systems GC1149A User manual

DRY CONTACT MODULE
GC1149A
INSTALLATION GUIDE
REV.12312015
RV AWNING PRODUCTS
1361 CALLE AVANZADO, SAN CLEMENTE, CA 92673 [phone] FAX [phone]
www.girardrv.com

Page 2of 7
Girard Systems awnings may be operated in light wind and rain
conditions. When periods of heavy rain and or high wind are expected
the awning must be closed. Never leave the awning open and
unattended.
Damage caused by wind and rain is not covered by warranty.
All awnings must be closed prior to moving the vehicle for any reason.
As an extra safety precaution a visual check that every awning is fully
closed is required.
Damage caused by failure to comply with these instructions is
not covered by warranty.
Before using your awning, ensure that the area into which the awning
will be deployed is free of obstructions (Trees, walls, pillars, posts,
other vehicles etc.)
Damage caused by collisions with any of the above or similar is
not covered by warranty.
Before using your awning make sure that all of your electrical circuits
are operating correctly. Recreational Vehicles can generate AC power
from three separate sources. The electrical system transfer switch in
your vehicle will select power for the awning as follows:
Shore Power – if connected;
Generator Power – if the generator is running;
Inverter Power – batteries must be charged for inverter operation.
Girard Systems awnings are supplied with an electric motor appropriate to the
product.

Page 3of 7
CONTENTS
Product Description …………………………………………………………………………. 4
Modes of operation …………………………………………………………………………. 5
Programming Steps ……………………………………………………………………… 6-7
THE G–LINK SYSTEM
The G-Link motors and control modules provided by Girard Systems communicate by
use of RF signals on a frequency of 433.92 MHZ. This eliminates the need for wiring
and the drilling of holes in the vehicle. These components must be electronically
matched, programmed or paired before use. This is usually done at the Girard Systems
factory. Should the need arise for the user to pair a device with the motor controller
they must refer to the appropriate manual for the devices applicable to their particular
installation.

Page 4of 7
PRODUCT DESCRIPTION
The GC1149A Dry Contact Module allows the user to interface their Dry Contact
Systems (Crestron, Switch Input or RV-C) with our G-link Controllers. This module will
accept Retract, Stop and Extend commands from the Dry Contact System and send an
RF signal to any programmed G-link Controller or Remote Motor. Using this module the
user will be able to operate their Girard awnings with their smart system.
Fig.1
Technical Specification
•Input voltage：12V/24V
•Transmitting frequency：433MHz
•Transmitting power：10 milliwatts
•Transmitting distance：500 Feet open area
•120 feet on two walls

Page 5of 7
MODES OF OPERATION
The GC1149A has 3 modes of operation;
1. Continuous Mode (Default) – A single press of a command button will allow the
awning to fully extend or retract unless interrupted by the STOP button.
2. Step Mode (Selected) – The command button must be held down to allow the
awning to fully extend or retract. The motor will stop as soon as the command
button is released.
3. Secondary Continuous Mode (Selected) – A single press of a command button will
allow the awning to fully extend or retract unless interrupted by pressing either the
same command button or the stop button.
To select each mode the module must be connected to a 12v power supply.
•Use a small screwdriver or similar tool to press and hold the SET button, a
blue/purple LED next to the set button will begin to flash 5 times slowly and then
ONCE quickly to indicate the DEFAULT mode.
•Continue to hold the set button (for about 12 seconds) until the LED flashes TWICE
quickly. This will select the STEP mode.
•Continue to hold the set button (for about 20 seconds) until the LED flashes 3
TIMES quickly. This will select the secondary continuous mode.
The LED will be
seen flashing here

Page 6of 7
PROGRAMMING STEPS
NOTE:
•Before starting this procedure the Receiver must be without power
(OFF) for at least 10 seconds.
•During the programming function the interval between each step
required must be less than 10 seconds
1. PROGRAMMING THE GC1149A TO A RECEIVER(GC136, GC154 or GC274A)
a. Connect the Dry Contact Control Module (GC1149A) to 12 Volts DC (Fig.1)
b. Make sure that the Receiver is powered ON
c. Press the program button on the Receiver: the Green LED of the Receiver
will start blinking
d. Press STOP on the Receiver: The Green LED will stop blinking and remain
illuminated.
e. Press the Retract button on the dry contact or using a small jumper from
Common to Retract, which will link the GC1149A to the motor controller: The
Green LED will turn off.
f. Note: Blue / purple light will flash on the GC1149A every time it transmits.
g. Try to operate the Awning by using the system or by using small jumpers
from common to retract terminal. If the Awning does not move, repeat steps
“a” to “e”.
2. Programming the 98GC1149A to the GC732G (DC Motor Control)
a. Connect the Dry Contact Control Module (GC1149A) to 12 Volts DC (Fig.1)
b. Supply power to the GC 732G: The unit will start beeping for least 5
seconds.
c. Press the Programming button for at least 3 seconds. (Red LED will turn ON
after 3 seconds).
d. Press the Retract button on the dry contact or using a small jumper from
Common to Retract terminal, which will link the GC1149A to the motor
controller: The Green LED will turn off.
e. Try to operate the Awning by using the system or by using small jumpers
from common to retract terminal. If the Awning does not move, repeat steps
“a” to “e”.

Page 7of 7
3. Programming the 98GC1149A to a Remote Motor
a. Connect the Dry Contact Control Module (GC1149A) to 12 Volts DC (Fig.1)
b. Supply power to the Remote Motor: a soft beep will be emitted by the RF
receiver in the unit.
c. Press the P2 button twice, (A beep will be emitted by the RF receiver with
each press)
d. Press the Retract button on the dry contact or using a small jumper from
Common to Retract, which will link the GC1149A to the motor.
e. Try to operate the Awning by using the system or by using small jumpers
from common to retract terminal. If the Awning does not move, repeat steps
“a” to “e”.
Note: If the motor turns in the opposite direction, repeat “a to e’ but now
use Extend instead of Retract.
For queries or assistance with programming any of your G-Link devices
please call Girard Systems TOLL FREE on 800–382–8442 between 7:30am
and 3:30pm P.S.T.