Glacier bay KINCAID 60 User manual

PAGE 1
2023-08-11 HOMEDEPOT.COM/HOMEDEPOT.CA/GLACIERBAY
KINCAID 60
GBSH176 / GBSH182
INSTALLATION MANUAL
Questions, problems, missing parts?
Before returning to the store, call Home Decorators Collection customer service department at
1-855-HD-GLACIER (1-855-434-5224)
8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday.
An installation video guide can be found on our Youtube channel:
https://tinyurl.com/f6kwtuaf

PAGE 2
CAUTION
Please carefully read the following important safety information before handling or installing this shower. There is a
risk of serious injury while handling this product. To minimize these risks, please note:
• Always wear safety glasses and gloves while handling.
• Always read and follow all the steps in the installation instructions.
• Inspect all contents and glass for damage before installation.
• Keep the corner protectors on glass panels until the installation is nished.
• Extreme caution should be taken while handling the glass during installation as the tempered glass may shatter if
in contact with a hard surface.
• Handle the tempered glass with caution! Improperly handling the glass can cause it to break suddenly in small
pieces (never in pointed fragments).
• Always take all precautions not to touch the tempered glass with any tools during the installation, or after installed.
• Do not cut or modify the tempered glass as it will shatter if cut.
• Carefully remove product from packaging and keep packaging until installation is complete.
• Inspect all parts for damage; if there is damage to the unit prior to installation, please contact customer service at
the number provided in this guide.
• Install the shower on a oor that is level and able to accommodate the weight of the unit and an occupant.
• Consult local building codes and compliance standards prior to installation and ensure conformity.
• After installation, and from time to time, check the glass for t and nish to ensure that nothing has come loose
since installation.
• Keep this installation manual for future reference.
SAFETY INFORMATION
NOTICE
Any modication or alteration from what is specied in this instruction manual will void any and all warranty on this
product.
The distributor is not responsible for any damage to the unit or personal property caused by improper installation. If
you disregard instructional warnings, you will void your warranty and possibly deal with water damage.
Consult the distributor’s website for any additional information or question on this product’s installation.
SAFETY NOTICE
PREPARATION
You will need at least two people to install this unit properly.
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list
and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

PAGE 3
SHOWER DIMENSIONS
C
28 9/16 in
D
32 1/2 in
A
72 in
E
25 in
A
72 in
*B*
57 1/16 in~60 in
F
9 in
Measures: inch
Measurements
AShower height
*B* Shower width
CFixed panel width
DDoor panel width
EDoor opening
FDistance between handle holes
*B*
ATTENTION!
This is the required shower space
measurement to install the shower.

PAGE 4
WALL-TO-WALL DIMENSIONS
WARNING!
**If you require to cut the bar, refer to the calculation below:
1. Measure the distance “D” at the height where the bar will be installed.
2. Cut the bar to a total length of L = D - 1/4 in.
3. The maximum measure to cut from the bar should be no more than 2 15/16 in.
72 in
L
L = D - 1/4 in
• Measure the thickness of your nished surface on either side before installing the metal tracks.
• Make sure to have a nished surface distance (D) between the min and max permissible dimensions according to the table
below.
*IMPORTANT: If needed you can cut the support bar to t the shower.
FINISHED SURFACE OPENING (D) SHOWER DOOR HEIGHT
(Make sure the door height is not surpassing your tile /
acrylic wall height)
Support bar adjustability
MIN** MAX*
57 1/16 in 60 in 72 in
D

PAGE 5
PACKAGE CONTENT
A1
x1
B
x1
C
1x
D
1x
E
1x
G
1x
I
2x
J
1x
H
2x
F1
1x
F2
1x
69 5/8 in
69 1/4 in
A2
x1
Wall track (left)
Chrome: 99STR-X421H552-WM
Matte Black: 99STR-SB5168SY-WM
Wall track (right)
Chrome: 99STR-14LE7D87-WM
Matte Black: 99STR-3C2JKT3K-WM
Door panel
99SGD-40V15K7J-WM
Fixed panel seal strip
Transparent: 99SRU-6DJSDRIM-WM
Matte Black: 99SRU-4591FEMT-WM
Support bar
Chrome: 99SGS-50AL1M5O-WM
Matte Black: 99SGS-OL6EQ4X3-WM
Glass panel vertical seal strip
Transparent: 99SRU-TRAL05Y9-WM
Matte Black: 99SRU-469NGONF-WM
Glass panel vertical seal strip
Transparent: 99SRU-TRAL05Y9-WM
Matte Black: 99SRU-469NGONF-WM
Support bar cover
Chrome: 99SDS-719QBVCU-WM
Matte Black: 99SDS-2890K0Q8-WM
Door roller
Chrome: 99SWE-48DFWJAD-WM
Matte Black: 99SWE-4UQJ453U-WM
Shower door stopper
Chrome: 99SDS-XN6RVS9U-WM
Matte Black: 99SDS-94C1V2HN-WM
Door panel vertical seal strip
Transparent: 99SRU-4CR6D889-WM
Matte Black: 99SRU-K8A92FF9-WM
Fixed panel
Chrome: 99SGP-NUTWTN07-WM
Matte Black: 99SGP-0314RN66-WM

PAGE 6
PACKAGE CONTENT
K
1x
L
1x
M
1x
N
2x
O
1x
P
1x
Wall track cover
Chrome: 99STR-026MXOUZ-WM
Matte Black: 99STR-7U4A16X7-WM
Door handle
Chrome: 99SHA-8AAA61L9-WM
Matte Black: 99SHA-G728EX69-WM
Decorative cap
Chrome: 99SGC4105-WM
Matte Black: 99SHW6134-WM
Decorative track
Chrome: 99STR3795-WM
Matte Black: 99STR3932-WM
Door bottom seal strip
Transparent: 99SRU-9ZCHQ1LV-WM
Matte Black: 99SRU-J091WO7D-WM
Sliding door guide
(with its rubber tting)
Chrome: 99SGC-58C9HPFP-WM
Matte Black: 99SGC-SZ5194ZF-WM
Complete hardware kit (refer to next page)
Chrome: 99SHW-SS7L9WX3-WM
Matte Black: 99SHW-FPK359S3-WM

PAGE 7
SUPPLIED HARDWARE LIST
TOOLS REQUIRED (not supplied)
BB
FF
EEAA
GG
CC DD
Screw
ST5x30mm
6+2
Wall Anchor
ø8x30mm
6+2
Cap
4x
Fitting
4x
Screw
ST4x20mm
1+1
Screw
ST4x15mm
4+1
Cap
1x
Allen key
2mm & 2.5mm & 3mm & 4mm
HH
Cap
1x
Wrench
2x
Pencil Screwdriver Drill and drill bits
ø1/8 in & ø5/16 in
LevelMeasuring Tape Silicone Rubber mallet
Cutter
Safety glasses Ratchet
3/16 in Bit socket
Glass suction cup

PAGE 8
DOOR ASSEMBLY OVERVIEW
A1
E
B
C
D
K
G
F2
H
I
J
M
N
O
P
L
A2
F1

PAGE 9
BEFORE INSTALLATION
For the easy installation of this shower please read the following important points:
• READ ALL the instructions completely before beginning.
• Make sure your walls are within 3/8 in of plumb. And wall corners should meet at 90oas illustrated.
• Make sure your tub or shower base is level.
• When using Solid Polymer Composite (SPC) shower walls, dry t your shower door and make sure there is a stud where the
wall track will be installed.
Please see the images below for Alcove shower.
90o
90o
LEVEL
LEVEL
90o
LEVEL
LEVEL
90o

PAGE 10
A B
PREPARATION
This instruction is drawn up for a door opening from right to left (see illustration A).
For an installation for a door opening from left to right (see illustration B), use the same
instructions, but switch around the panels: mirror e󰀨ect.
FAQ
Q: If the shower head is installed
on the other wall, will it leak?
A: It is possible to install your
shower head on the other side,
but we strongly recommend to
install it as illustrated.
Install the shower head on the door’s side as shown in the illustration!
This will reduce the risk of leaking.
DOOR DOOR
FIXED
PANEL
FIXED
PANEL
RIGHT DOOR
OPENING
LEFT DOOR
OPENING

PAGE 11
WALL TRACK INSTALLATION
1.1-1.2. Position the wall tracks (A1 & A2) as illustrated. Level the tracks (A1 & A2) and mark its outline and holes positions.
1.3. Remove the tracks and drill pilot holes in the marked locations with a ø5/16 in drill bit.
1.4. If there are no studs located behind the wall tracks (A1 & A2), then insert the wall anchors (AA) using a rubber mallet until
the wall anchors are ush with the wall.
1.5. Replace and secure the tracks (A1 & A2) with screws (BB). Do not overtighten.
NOTE: ALWAYS KEEP THE WALL TRACK (A1) ON LEFT SIDE IN BOTH RIGHT DOOR OPENING AND LEFT
DOOR OPENING INSTALLATIONS!
1
13/16 in
ø5/16 in
1.1
1.3
1.1
A1 A2
1.2 1.2
A1 A2
A1
A2
13/16 in
BB
1.5
A1 & A2
AA
1.4
WARNING!
If there are no studs aligned to the
wall track behind the drywall, use the
wall anchors to ensure the screws
won’t become loose.
AA
BB

PAGE 12
FIXED PANEL AND SUPPORT BAR INSTALLATION
2.1. Insert the xed panel (B) into the wall track (A1). Do not fully tighten it as further adjustments may be required.
2.2. Smoothly slide the sliding door guide (M) at the bottom of the xed panel (B), but without securing it.
2.3. Mark the position of the guide (M).
2
B
A1
2.1 2.2
B
MBM
2.3
B B
A1
A1
M M
RIGHT DOOR OPENING LEFT DOOR OPENING
A2
A2

PAGE 13
FIXED PANEL AND SUPPORT BAR INSTALLATION
3.1. Completely remove the guide (M).
3.2. Completely remove the xed panel (B).
3.3. Mark the positions of hole of the sliding door guide (M).
3.4. Drill a pilot hole for the sliding door guide (M) using a ø1/8 in drill bit.
3.5. Install the sliding door guide (M) with the screw (CC) and the cap (GG).
3
M
3.3
3.1
B
M
B
A1
3.2
ø1/8 in
3.4
HELPFUL HINT!
Add a drop of silicone in the
holes before inserting the screws.
3.5
M
GG
CC
A1
M
A2

PAGE 14
NEXT STEP MAY REQUIRE TO TRIM THE SUPPORT BAR (E) AND ITS COVER (G)
If the support bar is too long for your wall-to-wall opening “D”, you will have
to trim it down. Below calculation is for reference only: Ensure you made all
the proper measurements before you cut the bar.
1. Measure the distance “D” at the height where the bar (E) will be installed.
2. If D < 60 in, cut the bar (E) to a total length of L = D - 1/4 in.
3. After the bar (E) have been cut, cut the same length on the bar cover (G).
D
1
L = D - 1/4 in
2
EL
3
G

PAGE 15
FRAME INSTALLATION
INSTALLATION DU CADRE
INSTALACIÓN DE MARCOS
5FIXED PANEL AND SUPPORT BAR INSTALLATION
4.1. Insert the xed panel seal strip (D) and the support bar cover (G) into the bar (E).
4.2. Slide the 2 stoppers (I) and the 2 door rollers (H) onto the support bar (E).
4.3-4.4. Place the xed panel (B) into the wall track (A1) and put back the sliding door guide (M).
4
E
D
4.1
H
I
E
4.2
G
I
B
A1
4.3 4.4
B
M
B B
A1
A1
M M
RIGHT DOOR OPENING LEFT DOOR OPENING
A2
A2

PAGE 16
FRAME INSTALLATION
INSTALLATION DU CADRE
INSTALACIÓN DE MARCOS
5FIXED PANEL AND SUPPORT BAR INSTALLATION
5.1. Insert the wall track cover (K) to the wall track (A2) on the door side.
5.2. Insert the door bottom seal strip (P) onto the door panel (C).
5.3. Install the door vertical seal strip (J) on the closing end. For the door vertical seal strips, they should start right above the
door bottom seal strip (P).
5
B B
A1 A2
M M
A2
K
5.1
K K
A2 A1
RIGHT DOOR OPENING LEFT DOOR OPENING
C C
WARNING!
Before continuing,
place the door panel
(C) inside the shower
enclosure to facilitate
future steps!
J
5.3
C
P
J
C
P
5.2

PAGE 17
E
G
A2
NO GAP
FIXED PANEL AND SUPPORT BAR INSTALLATION
6.1-6.4. Insert the support bar (E) into the xed panel (B) and the wall track (A2), adjust the position of the support bar cover
(G), ensure there is no gaps at its 2 ends.
6
B
6.1 6.2
6.4
6.3
EE
A2
BE
G
NO GAP
B B
E E
A1 A2
A2 A1
RIGHT DOOR OPENING LEFT DOOR OPENING
G G

PAGE 18
FIXED PANEL AND SUPPORT BAR INSTALLATION
7.1-7.3. Drill guide holes through the wall tracks (A1 & A2) with a 1/8 in drill bit, as illustrated.
7.4-7.6. Screw the tracks (A1 & A2) in place using ttings (FF), screws (DD) and caps (EE).
7
7.2 7.3
7.4 7.5 7.6
FF
DD
EE FF
DD
EE
FF
DD
EE
3 15/16 in
RIGHT DOOR OPENING LEFT DOOR OPENING
FF FF
DD DD
EE EE
A2
ø1/8 in
ø1/8 in
B
A1
B BA1 A2
A2 A1
3 15/16 in
BA1
ø1/8 in
7.1
5/16 in

PAGE 19
SHOWER DOOR INSTALLATION
8.1. Disassemble the door rollers (H).
8.2-8.5. Place the door panel (C) into the guide (M), install the door panel (C) onto the door rollers (H) with their own bolt and
nut, do not strongly tighten yet. Adjust the level of the glass panel using the eccentric mechanism of the rollers. Finally, use a
wrench to strongly tighten the nut.
8
E
8.1
H
C
MH
C
8.2 8.3
8.4 8.5
H H
B B
C C
H H
RIGHT DOOR OPENING LEFT DOOR OPENING

PAGE 20
SHOWER DOOR INSTALLATION
9.1. Place the stopper (I) near to the wall track (A2, on the door side) and loosely secure it. Gently close the door until the door
roller (H) tightly anchors into the stopper (I). Measure the distance “X” between the wall and the lip of the door vertical seal strip
(J).
9.2. Open the door, loosen the stopper (I) and move it toward the wall by the distance “X”. Tightly secure the stopper (I).
9.3. Place the other stopper (I) on the other side of the support bar (E). The back of the stopper (I) has to be positioned 3 1/16
in from the wall. Tightly secure the stopper (I).
9
X
C
9.1 9.2
9.3
I
X
I
3 1/16 in
CB
H
J
I
I
I
A1
B
A2