Global Industrial 293034 User manual

User's manual Manual del usuario Manuel de l'utilisateur
Customer Service
US: 1-800-645-2986
Servicio de atención al Cliente
US: 1-800-645-2986
Service à la clientèle
Canada: 888-645-2986
1
Conned Space Vent Fan
293034
8" Conned Space Vent Fan
Rotomold Plastic,
1000 CFM, 1/3 HP
293035
8" Conned Space Vent Fan
w/ Rotomold Plastic Canister
& 25' Duct, 1000 CFM
293036
12" Conned Space Vent Fan
Rotomold Plastic,
2700 CFM, 1 HP
293037
16" Conned Space Vent Fan
Rotomold Plastic
4000 CFM, 1 HP
Safety Instructions
Please observe the following safety instructions to avoid personal injury and property loss.
1) Not operate any fan with a damaged cord or Plug.
2) Do not move or adjust blower while in operation
3) Keep this unit out of the reach of children
4) Do not alter or modify your blower in any way. Only authorized Global Industrial replacement parts can be
used. Use of any unauthorized parts could cause hazards and void the unit’s warranty
5) Always store unit in a clean, dry environment when not in use. Care should be taken to prevent water from
entering the unit’s motor. In the case that the unit’s motor does become wet, ensure that the motor is dried
thoroughly before use.
6) Do not allow water near or inside the unit while in use to avoid risk of electric shock. Handle unit with care to
avoid causing damage or personal injury.
7) Always operate the blower on a at, level surface. Operating the unit where it could slip or fall increases the
risk of injury, re, or electrical shock.
8) Never operate the blower without the factory-installed safety screens in place. This will prevent liquids, gases,
and other materials from entering the blower.
9) Do not use b lower near combustible gas or ammable materials in order to avoid re or electrical hazards.
10) Do not attempt to disassemble or repair unit on your own. Instead, bring to the attention of your distributor or
a certied repair center. Never attempt to disassemble or repair unit while blower is plugged in.
11) Prior to use, ensure the air intake and outlet are free of obstructions to prevent the blower from overheating
and causing a shock or re hazard.
WARNING: Read entire manual before installation, operation or maintenance.

Conned Space Vent Fan
2
User's Manual
Operating Procedures
The Global Industrial line of commercial ventilator is designed to eciently and eectively ventilate, extract and
circulate air. Be sure to follow all instructions below to ensure safe and eective use.
1) Ensure that the unit is on a stable, level surface, and remains stationary while in use.
2) Plug the blower into a grounded outlet with the correct voltage and amperage. Ensure that the unit is plugged
into a grounded outlet with voltage and wattage outputs that correspond with the unit’s specications. For
maximum protection against electrical shock, ALWAYS use a circuit that is protected by a ground fault circuit
interrupter. If you are unsure about the outlet, check with a qualied electrician.
3) Ensure that the dial is turned to your desired speed setting before turning the unit on.
CONTROLS
The ventilate Fan series equip the Water proof 1 speed switch.
Control Fan Speed with the Switch
1- Turn the fan on
0- Turn the fan o
Model 293034 293035 293036 293037
P ower Input 115Volt/60hz 115Volt/60hz 115Volt/60hz 115Volt/60hz
P ower 1/3hp 1/3hp 1hp 1hp
C urrent 2.6amps 2.6amps 11amps 11amps
Motor Speed 3450rpm 3450rpm 3450rpm 3400rpm
Air Volume 1000cfm 1000cfm 3000CFM 4000cfm
Outlet Size 8inch 8inch 12inch 16inch
S ize 14x10x15inch 33x14x14inch 19.7x15.4x21.5inch 20x21x23inch
Weight 16lbs 37lbs 31lbs 39lbs
Specications may change without notice.
Maintenance
1) Inspect the electrical cord and wiring for damage or discoloration before use. NEVER use a blower that has a
damaged cord to avoid risk of electrical shock or re.
2) Inspect for loose fasteners before each use.
3) Clean safety screens of the unit before each use.
4) Listen for abnormal sounds and shut unit o immediately upon hearing unusual noises.
5) Keep unit clean and free of blockages or obstructions.
6) Use compressed air or a vacuum to remove lint and other debris from the motor, inlet, or fan blade.
7) Do not use a pressure washer, water hose, or other water source to clean the unit. Ensure that the unit is
completely dry before each use.
8)
The blower has sealed bearings and cannot be lubricated. No oiling is necessary.
For information about authorized repair and maintenance contact Global Industrial.
Specifications

3
Trouble Shooting
BLOWER DOES
NOT TURN ON
1) Switch not turned on - in this case, ensure that the knob is in the correct
position to turn the unit on
2) Circuit breaker or GFCI has tripped - press ‘reset button before attempting
to turn the unit on
3) Cord or wires are loose or damaged - Inspect to ensure that cords and wires
are tight and free of damage
4)
Faulty switch - Contact your distributor if inside warranty period
BLOWER STARTS AND THEN
TURNSOFF
1) Obstructed inlet/outlet - remove obstructions and ensure that both inlet and
outlets are clear before use.
2)
Faulty motor - Contact your distributor if inside warranty period
BLOWER VIBRATES
1) Motor shaft is bent - Contact your distributor if inside warranty period
2) Fan blade is bent - Contact your distributor if inside warranty period
3) Excessive dirt built up on fan blade - Clean blade and ensure blade housing
is free of dust and dirt before use
BLOWER MAKES SCRAPING
NOISES
1) Damaged housing - Inspect housing for warps or dents. If housing is
rubbing against blade, contact your distributor.
MOTOR MAKES NOISE, BUT
BLOWER WON’T TURN ON
1)
Damaged/faulty motor or motor shaft - Contact your distributor if inside
warranty period
2) Motor shaft screw holding fan blade is loose - tighten
Conned Space Vent Fan