Global Industrial 600554 User manual

1
BELT DRIVE DRUM FAN
CAUTION
WARNING
Read and follow all instructions before operating fan.
Do not use fan if any part is damaged or missing.
- To reduce the risk of fire or electrical shock, do not expose
to water or rain.
- To reduce the risk of fire or electrical shock, do not use this
fan with any solid state speed control device.
- Automatically operated device - To reduce the risk of injury,
disconnect from power supply before servicing.
- If the power supply cord is damaged, contact your local
service centre or a qualified electrician to install an
appropriate replacement cord to prevent any injury or damage.
- The appliance does not apply to be used in locations where
special conditions prevail, such as the presence of a
corrosive or explosive atmosphere ( dust, vapour or gas ).
- This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play
with the appliance.
RULES FOR SAFE OPERATION:
●Never insert fingers or any other objects through the grill
guard when fan is in operation.
●Disconnect the fan from its power source when moving
from one location to another.
●Disconnect the fan from its power source when removing
guards for cleaning.
●Be sure fan is on a stable, flat surface when in operation.
●Do not use fan in windows. Rain and moisture may create
electrical hazard.
●Close supervision is necessary when this fan is used near
children, the elderly and pets.
●Do not place the fan near an open flame, cooking or heating
appliance, or hot surface.
●This fan should not be operated outside.
CAUTION: Do not alter the fan's assembly.
WARNING: Be sure that both front and rear guard screws are completely tightened in locking position before operation.
OPERATING INSTRUCTIONS
TO ADJUST AIRFLOW UPWARD OR DOWNWARD: Tilt fan head to the desired angle. This high velocity fan can be
used alone or in conjunction with air conditioning. Rotating the fan head upward serves to pull air from the floor and
circulate it throughout the entire room.
SPEED CONTROL:
CLEANING
WARNING: Unplug from electrical supply source before cleaning.
1. Use soft damp cloth to clean, then wipe with dry cloth.
2. Do not use a cleaning solution that is harmful to paints or plastics.
3. Do not bend the blades.
Select air speed by setting switch to either HIGH - LOW - OFF.
It is normal for the motor to feel warm to touch after continuous operation. This fan features a thermostat that will automatically
shut off should it overheat for any reason. If this happens, immediately unplug the fan from the outlet.
Models
600554
600555

。
 

1. Insert axle shaft through the frame. Align the holes in
the frame to the screws in the axle. Secure washers
and Hexagon nuts with a wrench as shown.
2. Slide in each wheel over end of each axle shaft and
secure with Hexagon bolts and washers.
3. Tighten Hexagon bolts.

2
VENTILATEUR A TAMBOUR
Choisissez la vitesse en plaçant l’interrupteur a Haut, bas, arrêt.
Il est normal que l’appareil soit chaud au touché avec une utilisation continue.Ce ventilateur est muni d’un thermostat
qui arrêtera l’appareil automatiquement s’il devient trop chaud. Dans une telle situation, débranchez immédiatement
l’appareil.
Modèles
。
Roue Boulons hexagonaux et rondelles
1. lnserez l'arbre de roue dans le chassis. Alignez les trous dans
le chassis aux vis dans l'arbre. Fixez les rondelles et les
ecrous hexagonaux avec une cle comme illustre.
2. Glissez chaque roue sur l'extremite de chaque arbre et fixez
avec les boulons hexagonaux et les rondelles.
3. Resserrez les boulons hexagonaux.
600554
600555
INSTRUCTION D'ASSEMBLAGE DE LA ROUE 