Global Industrial RXHS-361872 Instruction Manual

Extra shelves are also available (RXHS-wwdd).
LOAD CAPACITIESLOAD CAPACITIES
PER SHELF LEVEL*PER SHELF LEVEL*
36w x 18d
36w x 24d
48w x 18d
48w x 24d
60w x 24d
4000 lbs.
4000 lbs.
4000 lbs.
4000 lbs.
3250 lbs.
UNIT SIZEUNIT SIZE WT. CAPACITYWT. CAPACITY
*Total Unit Capacity not to exceed 13,000 lbs.
RETAIN INSTRUCTIONS FOR FUTURE REFERENCERETAIN INSTRUCTIONS FOR FUTURE REFERENCE
ASSEMBLY INSTRUCTIONS & PARTS MANUAL
Heavy-Duty Reinforced High Capacity Shelving
36” Wide, 46” Wide & 60” Wide Units
Global Industrial, 111 Harbor Park Dr., Port Washington, NY 11050 • [phone] • [email protected]
GENERAL SAFETY INFORMATIONGENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.
For safety, wear a pair of work gloves when assembling or performing any maintenance on the unit.

ASSEMBLY OF HEAVY-DUTY HIGH CAPACITY SHELVING
Two people are recommended for assembly. Approximate assembly time: 35-45 minutes per section.
The reference numbers used throughout this sheet refer to the illustration on the back cover.
This is to help you to identify the various parts as they are mentioned.
4. Lay the bottom shelf decking (Ref. No. 5) on the shelf supports
so that the front and back edges overlap the front and back
shelf supports.
1. With help from an associate, or using a wall for support,
create a unit end by connecting two SUR uprights together
(Ref. No. 1) with two front-to-back end shelf supports (Ref.
No. 2), one at the top and one at the bottom. Be sure the
supports are fully seated in the slots. Repeat to construct a
second unit end.
2. Next, connect the two unit ends with two LRA left-to-right
shelf supports (Ref. No. 3), temporarily leaving off one of the
top left-to-right supports.
NOTE: It is important that one top left-to-right support be
temporarily left off in order to later insert the upper shelves.
3. Attach one front-to-back center shelf supports (Ref. No. 4) by
inserting the deck support keyhole slots over the rivets on the
 supportsandtappingthemrmlyintoplace.
IMPORTANT! All shelf
supports should be
inserted with the
return flange on top,
as shown at right.
(This flange is what the
shelves will rest upon)
NOTE: Inset is shown
from opposite side.
NOTE: One left-to-right
support is not inserted
until step 8.

NOTE: Bolts are not needed to secure the deck supports on
the bottom shelf because it rests on the oor. All other levels
require these bolts to achieve maximum load capcities.
NOTE: Every fourth slot in the uprights has a at top to
help visually align the supports.
5. Attach shelf supports at the next desired shelf level.
Once the shelf supports are in place, attach a front-to-back
center supports as you did in step 3. Lower the steel decking
into place, as described in step 4.
NOTE: Be sure to bolt both the front
and rear of each shelf. This requires
two bolts per shelf.
7. Attach the remaining shelf supports and decking at the
desired shelf levels, completing one level at a time.
NOTE: Once all but the top shelf are in place, attach the
remaining left-to-right shelf support at the top level.
8. After attaching the top decking and securing it with
two sets of bolts, your die rack unit is fully assembled
and ready for use.
6. Once the decking is in place, secure it to the shelf supports
with two sets of 1/4-20 x 5/8bolts and nuts (Ref. No. 6).
Do this by placing one bolt through each hole in the front
and rear of the decking, making sure the bolt goes through
the decking and shelf supports as shown below.
Tighten securely.

REPLACEMENT PARTSREPLACEMENT PARTS
Steel Decking
(Ref. No. 5)
Front-to-Back Center
Shelf Support
(Ref. No. 4)
Front-to-Back
End Shelf Support
(Ref. No. 2)
Bolts and Nuts
1/4-20 x 5/8”
(Ref. No. 6)
Heavy
Upright Post
(Ref. No. 1)
Left-to-Right
Shelf Support
(Ref. No. 3)
Global makes every effort to ensure that all units ship complete with all parts and arrive undamaged.Global makes every effort to ensure that all units ship complete with all parts and arrive undamaged.
However, should your unit contain missing or damaged parts, please contact your purchase location.However, should your unit contain missing or damaged parts, please contact your purchase location.
NOTE: Additional hardware may be included for replacement purposes.NOTE: Additional hardware may be included for replacement purposes.
REF.REF.
NO. DESCRIPTIONNO. DESCRIPTION
1 Heavy Upright Post 4 SUR-hh* SUR-hh* SUR-hh* SUR-hh* SUR-hh*
2 Front-to-Back End Shelf Support 10 LRA-18 LRA-24 LRA-18 LRA-24 LRA-24
3 Left-to-Right Shelf Support 10 LRA-36 LRA-36 LRA-48 LRA-48 LRA-60
4 Front-to-Back Center Shelf Support 10 SDS-18 SDS-24 SDS-18 SDS-24 SDS-24
5 Steel Decking 5 ZS-3618 ZS-3624 ZS-4818 ZS-4824 ZS-6024
6 1/4-20 x 5/8” Bolts and Nuts
PART NUMBERSPART NUMBERS
RXHS-361872RXHS-361872
RXHS-361884RXHS-361884
RXHS-361896RXHS-361896
QTY.QTY.
AVAILABLE LOCALLY
RXHS-362472RXHS-362472
RXHS-362484RXHS-362484
RXHS-362496RXHS-362496
RXHS-481872RXHS-481872
RXHS-481884RXHS-481884
RXHS-481896RXHS-481896
RXHS-482472RXHS-482472
RXHS-482484RXHS-482484
RXHS-482496RXHS-482496
RXHS-602472RXHS-602472
RXHS-602484RXHS-602484
RXHS-602496RXHS-602496
* SUR-hh, where “-hh” indicates height of the upright post. Example: a 72” upright post for RXHS-361872 would be “SUR-72”