Global Industrial Bench-In-A-Box B2334698 User manual

User's manual Manual del usuario Manuel de l'utilisateur
Customer Service
US: 1-800-645-2986
Servicio de atención al Cliente
US: 1-800-645-2986
Service à la clientèle
Canada: 888-645-2986
MODEL #
1
1. Sleeve leg Extender into leg at desired
Height and place bolt assembly as
shown and tighten.
2. Screw nylon glide into leg extenders.
3. Assemble front and back rail using stud
plates and lock nuts provided. The 2 x 2
x 1 channel is for the front of the unit
and the 1 x 8 channel is for the rear then
attach the 1/4" - 20 x 3/4" hex head bolt
and flat washer to the bottom most hole
in the back rail. (before tightening nuts,
make sure that the front rail and the
back rail are pushed inward
approximately 1/8" to allow the
worksurface to be mounted properly),
Note: Holes in rails should be facing up.
4. Place worksurface bottom up on a
protected surface (to protect laminate
from scratches). Place assembled frame
on backside of top, locate flush with
back edge of leg. (seam of edging to
back). Pre-drill holes 1/2" deep and
screw #12 x 3/4" screws in to secure
frame to top.
5. Set bench upright and adjust nylon.
Bench-In-A-Box
Technical Workbench
B2334698: 72"W x 30"D ESD Laminate Top (ref page 3)
B2334699: 72"W x 30"D Plastic Laminate Top
B2334700: 60"W x 30"D ESD Laminate Top (ref page 3)
B2334701: 60"W x 30"D Plastic Laminate Top

2
Technical Workbench
1. Sleeve leg extender into leg at desired height and place bolt
assembly as shown and tighten.
2. Screw Nylon glides into leg extenders.
NOTE: If the leg extenders are fitting tightly and are not sliding easily
into the legs, remove extender and with a rubber mallet hit along both
sides of the extender to slightly bend the channel inwards.

3
Technical Workbench
1. Assemble footrest as shown using 1/4" - 20
x 2 1/4" flat allen head bolt, finish washer,
flat washer and kepnuts provided.

4
fTechnical Workbench
1. Drill 3/8" hole in work surface per
measurements in the top view (if not
already pre-drilled).
2. Install 5/16" x 2 1/2" hex head bolt, ring
terminal and serated through work
surface. On underside of work surface
install washer, ring terminal, washer,
ringer terminal, washer, and nut in this
order and tighten.
3. Mount Jacks into front rail using nuts
provided.
4. Run wires in manner shown in top view
using wire ties and self stick pads (4 to 6
per bench)
NOTE: Pads stick better to metal surfaces.
5. Cut wires to appropriates length by
pulling wires (to remove excess slack)
towards the hole in the work surface and
adding 1" to that. Strip wires back 1/4"
and install the ring terminal by crimping it
to both exposed wires at the same time.
ESD installation only for below models:
B2334698: 72"W x 30"D ESD Laminate Top
B2334700: 60"W x 30"D ESD Laminate Top

5
Technical Workbench
1. Remove drawer from housing.
2. Mount brackets to drawer using 1/4" x
3/4" hex head bolts and washers as
shown.
(tighten bolts on rear bracket but leave
bolts on front plate loose).
3. Slide housing over front rail of bench
sandwiching front rail between housing
and plate.
4. Set drawer housing a minimum of 1"
away from leg and 3/4" set back from
front rail .
5. Install five (5) #12 Phillips pan head
screws through rear bracket and into
bottom of the work surface. Tighten the
bolts securing the front hanging plate.
Note: Drawers are more easily mounted
when bench is flipped upside down.
1. Mount brackets as shown to the padlock
drawer using 1/4" hex head bolts, nuts and
washers. (tighten bolts on rear bracket nut
leave bolts on front plate loose).
2. Slide padlock drawer over front rail of
bench sandwiching front rail between
padlock drawer and plate.
3. Set the padlock drawers as close to the left
leg as possible and flush with the front rail.
4. Install #12 Phillips pan head screws
through rear bracket and into bottom of
the worksurface. Tighten the bolts
securing the front hanging plate.
Note: Padlock drawers are more easily
mounted when bench is flipped upside
down.

6
Technical Workbench
1. If worksurface is not already pre-
drilled, drill the worksurface with 3/8"
dia. drill bit per dimensions for your
particular size shelf on drawing and
chart.
2. Mount the electrical back brace and
front brace to riser legs using 1/4"
-20 x 3/4" truss head bolt.
3. Mount shelf evenly on riser assembly
(front brace and riser legs) using #12
3/4" Phillips pan head screws (make
sure that the "seam of the "T" mold
edge is facing the rear of the station
and that there is equal overhand on
either side and for front to back
overhang, locate that dimension on
the chart.
4. Mount riser leg assembly to the
worksurface with 1/4" x 2" flat allen
head bolts provided.

7
Technical Workbench