Clarke CWB1250 User manual

Thank you for purchasing this CLARKE Heavy Duty Workbench, which, if treated
with care and respect, will give years of reliable and satisfactory service.
Guarantee
This product is guaranteed against faults in manufacture from 12 months from
purchase date.
Keep your receipt as proof of purchase. This guarantee is invalid if the product
has been abused or tampered with in any way, or not used for the purpose for
which it was intended. The reason for return must be clearly stated. This guarantee
does not affect your statutory rights.
HEAVY DUTY WORKBENCH
0107
Model CWB1250
HEAVY DUTY WORKBENCH

1Hold the top panel (2), on its edge so that the
blind hole on the inside edge, at one end, which
is used to locate the cupboard door swivel pin,
is uppermost, facing you and to the right. FIG.1
2 Ensuring the panels are correctly oriented
attach the two side panels, (3 & 4) and the
centre panel, (5), using the screws, nuts and
washers provided. FIGS .2 & 3.
Remember - DO NOT tighten the nuts fully.
NOTE: The shelf supports attached to the end
and centre panels should be facing each other,
on the left side of the structure. FIG.3
The structure should now be resting on its side
with the three panels facing you.
Pre-Assembly check.
Unpack the components and lay out carefully. Referring to the parts list, ensure that all parts
are present. If there are any deficiencies, immediately contact the dealer from where the
product was purchased, or the Clarke International Parts Department on, 020 8988 7400.
Assembly is quite straightforward and requires the use of a screwdriver and a 10mm spanner
3 Attach the bottom panel in the same
manner as in ‘1’ above, i.e. by holding it
on its edge with the blind hole on the inside
edge uppermost. FIG.4.
Get an assistant to hold the door so that
as the back panel is offered up, the swivel
pins are entered in the two blind holes in
the top and bottom panels. FIG.4
4 Turn the structure so that it rests on its front...i.e.
the door, and attach the back panel (7).
REMEMBER - DO NOT tighten the nuts fully.
5 Whilst in this position, attach two legs, one
to each corner, then turn the structure so
that it rests on its back once again and
attach the two front legs. FIG5
6 Turn the complete assembly on to its feet
and rock it gently in order to align all
parts and to ensure that no particular
part is under stress. Ensure also that the
legs are vertical and particularly, that
the door is perfectly square in its recess.
When completely satisfied, tighten all
nuts and screws so far assembled.
FIG.1
Assembly
Note: When assembling, all screw heads should be on the outside of the cabinet.
IMPORTANT: DO NOT tighten any nuts until the cabinet is fully assembled.
The numbers in brackets refer to the item number on back page
FIG.2
On its Edge
Back
Front
FIG.3

FIG.4
FIG.5
7Using the empty carton as a clean
base, place the worktop (1) face down
- pre-driled holes uppermost and attach
the drawer guides (14) using the wood
screws provided, ensuring they are tight.
The drawer runners should face each
other.
NOTE: The holes may need opening out
slightly by very carefully drilling with a small
drill - smaller that the root diameter of the
woodscrew.
8 With the runners attached, turn the
worktop over and bolt it securely to the
base unit via the top of each leg. Ensure
the drawer guides are at the front of
the unit.
9 Insert the door lock into the hole in the
door and secure firmly into place using
the ‘C’ shaped washer.
10 Place the shelf on its rails.
11 Fully tighten any nuts not yet secure.
12 Assemble the drawer as follows:
The drawer comprises:
2 x Side panels, 1 x Front Panel, 1 x Back
Panel, 1 x Bottom panel
FIG.6
For Spare Parts and Service, please contact your nearest dealer,
or CLARKE International, on one of the following numbers.
PARTS & SERVICE TEL: [phone]
PARTS & SERVICE FAX: [phone]
or e-mail as follows:
PARTS: [email protected]
SERVICE: [email protected]
PARTS & SERVICE CONTACTS
a. Having identified the various parts bolt the side
panels to the front panel in the manner shown
in the diagram below, then bolt on the back
panel ...all screws should be finger tight.
b. Drop in the bottom panel, and secure using
the screws, washers and nuts supplied.
Ensure the drawer is square before tightening
all nuts.
c. Attach the handle and tighten nuts.
d. Slide the drawer into place, and your
workbench is ready for use.

Assembly Diagram
1 Worktop RO125001
2 Top Panel RO125002
3 Side Panel (L) RO125003
4 Side Panel (R) RO125004
5 Centre Panel RO125005
6 Legs RO125006
7 Rear Panel RO125007
8 Bottom Panel RO125008
9 Door RO125009
10 Door Lock RO125010
11 Drawer (5 Panels) RO125011
14 Drawer Guide RO125014
15 Shelf RO125015
- Screws, washers & nuts (set) RO125016
- 21mm Wood screw - RO125017
NOTE:
Washers and nuts
always located on the
inside during
assembly