Goalsetter Systems GS Wall Mount User manual

GS WALL MOUNT
Junior Wall-Mounted Goal Systems
Made In The USA
Installation
& Owner’s
Instructions
• 36" Junior
Wall Mount

Junior Wall Mount Instructions
This manual explains the proper
installation, operation and maintenance of
your Goalsetter Goal. Study and
understand these instructions thoroughly
before installing, operating or maintaining
the goal. Failure to do so could result in
serious injury or death and/or equipment
damage. Consult your Goalsetter dealer or
Goalsetter Systems, Inc. if you do not
understand the instructions in this manual
or need additional information.
Goalsetter Systems, Inc. recommends that
you retain this manual for future reference
of operation, maintenance and parts
information.
The instructions, illustrations and
specifications in this manual are based on
the latest information available at the time
of publications. Your goal may have
product improvements and options not yet
contained in this manual.
Goalsetter Systems, Inc. reserves the right
to make changes at any time without
notice or obligation.
Additional copies of these instructions are
available from Goalsetter Systems, Inc.
2 www.goalsettersystems.com 800.362.GOAL (4625)
GOALSETTER®, GOALSETTER SYSTEMS®AND GOALSETTER®logo
are all registered trademarks of Goalsetter Systems, Inc. in the U.S.
and/or other countries.
GS™and BEST IN BASKETBALL™are trademarks of Goalsetter
Systems, Inc.
This product is covered by various U.S. and Canadian patents,
including U.S. Patent #5,211,393.
Patent infringement will be prosecuted.
No part of this manual may be reproduced in any form or by any
means electronic or mechanical, including photocopying, recording,
or by any information storage and retrieval systems without the
express written consent of Goalsetter Systems, Inc.
Copyright 2006.
Revised 12/9/2008.
All Rights Reserved.
Goalsetter Systems, Inc.
Questions? Comments? Contact Us:
Phone: [phone] • Fax: [phone]
Email: [email protected]
www.goalsettersystems.com

Junior Wall Mount Instructions
TABLE OF CONTENTS
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Goal Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Goal Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Required Tools and Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Hardware Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Frame Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Rim Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Frame Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Operation and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-15
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Warranties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
800.362.GOAL (4625) www.goalsettersystems.com 3
Thank you and congratulations for purchasing a Goalsetter Goal – the finest
basketball goal system on the market today! You will discover that Goalsetter is
unsurpassed in product innovation, quality and integrity in the basketball equipment
industry. We are continually focused on designing, engineering and producing
products that meet and exceed the expectations of today’s toughest playing
environments and demanding players.
Our commitment is to all those who want to play the game of basketball – to be able
to train at whatever level they are at and then shoot for the stars. We are also
committed to you, our customer, long after the sale has been made. Please contact us
if you have any concerns, questions or suggestions regarding our products. Again,
we are honored that you have purchased our goal system and we look forward to
helping you with your game in the years ahead.
THANK YOU!

Junior Wall Mount Instructions
4 www.goalsettersystems.com 800.362.GOAL (4625)
Failure to follow these safety instructions may result in serious injury or death
and/or property damage.
•Do not install or use this product unless the
instructions within this manual have been
carefully read and understood.
•Consult your Goalsetter dealer or Goalsetter
Systems, Inc. if you do not understand the
instructions in this manual or need additional
information.
•If using a ladder during assembly, use extreme
caution. Two or three people are recommended
for safe installation and assembly.
•Installation and assembly of this product will
require lifting and bending that may result in
injury to anyone not accustom to this type of
activity.
•Ensure there are no overhead power lines
within a 20 ft. (7 m.) radius of the goal location.
•Climate, corrosion or misuse could result in
system failure.
•If the unit is installed with the rim at a 6'-0"
playing height, the minimum operational
height will be 5'-4" (1.9 m) to the bottom of
the backboard.
•DO NOT HANG on the rim or any part of the
goal system. This includes the backboard,
support braces or net.
•During play, especially when performing
dunking activities, keep the player’s face away
from the backboard, rim and net. Serious injury
could result if teeth/face come in contact with
the backboard, rim or net. Do not wear jewelry
or other loose objects that could become
entangled in the net.
•Twice yearly, check the goal system for loose
hardware, excessive wear and signs of
corrosion. Repair the system before use.
•Never play on damaged equipment.
SAFETY INSTRUCTIONS

Junior Wall Mount Instructions
800.362.GOAL (4625) www.goalsettersystems.com 5
GOAL SPECIFICATIONS
B
A
C
G
F
H
Playing Surface
Backboard Size 25" x 36"
Weight With Glass 36 lbs.
Height Range (A) 6'
Extension Distance (B) 5-3/4"
Rim To Top-Of-Goal Distance (C) 20"
Bottom Of Frame Height (F) 69-1/8"
Frame Size (G) 15"
Top Of Frame Height (H) 84-1/8"
GOAL ASSEMBLY
Goalsetter Systems cannot assume liability for the installation of
any wall-mounted structure. Goalsetter Systems recommends
consulting a professional architect or contractor to determine a
safe wall anchoring system to match the wall construction being
used in your application.
IMPORTANT: Safe assembly of the goal requires two to three people
in good physical condition and capable of lifting 80-100 lbs (36-45 kg)
each.
IMPORTANT: Locate and familiarize yourself with all parts of the goal
before beginning assembly.
NOTE: The type of wall fasteners and drill bits required are determined
and provided by the customer and/or installer.
Level
Rubber Mallet
12' Tape Measure
Ratchet
Socket Extension
9/16" Socket
9/16" Wrench
Wall Fasteners (not included)
Drill and Drill Bits (masonry
if necessary)
Required Tools and Materials

Junior Wall Mount Instructions
6 www.goalsettersystems.com 800.362.GOAL (4625)
3
PARTS LIST & DESCRIPTION – JUNIOR WALL MOUNT
56
NOTE: Refer to page 7 for hardware descriptions.
Backboard
Assembly
Rim & Net
Assembly, Rim
Bolt Backplate,
& Hardware
1Frame 4
2Hardware
4 places
REF MINI WALL MOUNT DESCRIPTION
11Frame
2a 4 Bolt, 3/8"-16 UNC x 1-1/4"
2b 8 Flat Washer, 3/8"
2c 4 Locknut, 3/8" UNC
31 Backboard Assembly, 25" x 36"
41 Rim and Net Assembly
5a 4Bolt, 3/8"-16 UNC x 2"
5b 8 Flat Washer, 3/8"
5c 4 Lock Washer, 3/8"
5d 4Nut, 3/8"-16 UNC

Junior Wall Mount Instructions
800.362.GOAL (4625) www.goalsettersystems.com 7
HARDWARE IDENTIFICATION
NOTE: Refer to page 6 for descriptions and quantities.
Rim Bolt Assembly
(#5 in Parts List)
Description Parts List Length
Callout
Mounting Bolt (at backboad) #2 1-1/4"
Black Touch-Up Paint

Junior Wall Mount Instructions
8www.goalsettersystems.com 800.362.GOAL (4625)
FRAME ATTACHMENT
IMPORTANT: Safe assembly of the
goal requires two or three people in
good physical condition and
capable of lifting 80-100 lbs (36-45
kg) each.
Step 1: Unpack frame.
Step 2: Determine where to place
frame on mounting surface.
Step 3: Goal can be mounted at
any height preferred. To mount at a
rim height of 6', draw a horizontal
line on the mounting surface 69-
1/8" up from playing surface.
Step 4: Position frame 1 on wall
with with bottom of frame centered
on drawn line 2 .
Step 5: Level frame horizontally
and vertically using a level. Mark
wall mounting holes needed for
attachment of frame. (To be
determined by customer and/or
installer.)
Step 6: Set frame down.
Step 7: Drill holes as needed in
mounting surface.
Step 8: Loosely attach frame to
wall using correct fasteners. (To be
determined by customer and/or
installer.) Level frame horizontally
and vertically using a level.
Step 9: Fully tighten fasteners.
1
16"
Mounting Hole
2
69-1/8" Up From
Playing Surface
For 6' Rim Height

Junior Wall Mount Instructions
800.362.GOAL (4625) www.goalsettersystems.com 9
RIM ATTACHMENT
2
3
4
Step 1: Remove any cardboard edge
protectors and protective sheeting from
backboard.
NOTE: Four steel shouldered bushings 1
are factory installed. If loose, make sure
to have them seated properly when
tightening rim bolts. If missing, contact
Goalsetter or dealer to get replacements.
DO NOT install rim without bushings.
IMPORTANT: Correct sequence of
hardware installation MUST be followed
during assembly.
Step 3: Loosely attach rim 4 to
backboard through top mounting holes 2
with two 3/8" x 2" bolts, four flat washers,
two lock washers and two nuts. Snug
tighten hardware – a 9/16" open-end
wrench may be necessary. NOTE: Attach
rim to backboard before mounting
backboard to mounting bracket on
wall.
Hardware Sequence: Bolt passes through flat
washer - rim backplate - backboard bushing -
backboard mounting plate - flat washer - lock
washer - nut.
Step 4: Repeat procedure outlined in
Step 3 for lower rim mounting holes 3 .
Step 5: Level rim side to side and then
fully tighten hardware.
Step 7: Attach net to rim.
1
56

Junior Wall Mount Instructions
10 www.goalsettersystems.com 800.362.GOAL (4625)
IMPORTANT: Use two or more
people to raise backboard into
position. They should be in good
physical condition and capable of
lifting 80-100 lb (36-45 kg).
Step 2: Lift backboard 1 into
position and attach to mounting
plates.
•Make sure backboard frame is
between the mounting plates.
• Attach with four 3/8" x 1-1/4"
bolts (#2 in parts list), eight flat
washers and four locknuts – do
not fully tighten.
Hardware Sequence: Bolt passes through
flat washer - mounting plate - frame flange
- flat washer - locknut.
Step 3: Fully tighten all fasteners.
FRAME ASSEMBLY
1

Junior Wall Mount Instructions
800.362.GOAL (4625) www.goalsettersystems.com 11
Goalsetter uses a two-part acrylic-enamel paint on our
goals. With periodic inspection and service when
needed, the high-gloss finish is designed to last for
many years. A small bottle of black paint with brush is
provided with every goal for touch up of imperfections
as they develop and can be found in the hardware kit.
If more touch up is required, please contact Goalsetter
Systems, Inc. or your local Goalsetter Dealer.
MAINTENANCE
The exterior finish of your Goalsetter goal is designed for outdoor
environments and should only require periodic cleaning and inspection for
imperfections that could develop over time (see Maintenance section).
When cleaning is necessary, Goalsetter recommends using water and a mild
dish detergent applied with a soft, non-abrasive cloth.
IMPORTANT: DO NOT use abrasive cleaners to clean the goal. Damage to
the finish may result.
CLEANING

12 www.goalsettersystems.com 800.362.GOAL (4625)
BUYER AGREES THAT PRODUCTS SOLD BY GOALSETTER SYSTEMS, INC. CARRY THE FOLLOWING WARRANTY
Subject to proper installation and normal, intended use, all structural components of Goalsetter Systems Signature Series*, Extreme
Series* and GS Wall-Mount Series* basketball systems are warranted to be free of defects in material and workmanship for the duration
of ownership by the original retail purchaser, subject to the limitations below. Tournament Series* systems will be covered by this
warranty for a period of five years. GS Portable Series* systems will be covered by this warranty for a period of two years. Goalsetter
shall have the right to require the purchaser to deliver the allegedly defective product to Goalsetter for testing, repair or replacement.
Goalsetter shall not be responsible for any expenses associated with the replacement or removal of the product from its application for
such delivery. Modification of any product by the customer, unless approved by Goalsetter Systems, will void all warranty. Where listed as
“LIMITED”, the warranties shall cover damage or failure that occurs during the course of NORMAL or INTENDED USE of the product.
Normal or intended use shall be described as activity that is necessary for the participation in the sport for which the equipment is
designed. NOT COVERED is damage caused by deliberate hanging, multiple player hanging, vandalism, non-basketball activities or any
other activity that could be regarded as abusive. *Signature Series – MVP, Captain, All-American, All-Star, Contender, Champion; Extreme Series – X672,
X660, X560, X554, X454, X448; GS Wall-Mount Series – GS72 Wall-Mount, GS60 Wall-Mount, GS54 Wall-Mount, GS48 Wall-Mount; Tournament Series – Elite, Classic;
GS Portable Series – GS1000, GS2000, GS2500, GS3000, GS3500
Any warranty on a basketball system excludes the rim. Rim warranties are as follows: Single Ring Static Rim: two-year limited;
Double Ring Static Rim: Unconditional Lifetime; Home Court Flex Rim: one-year limited; Heavy Duty Flex Rim: two-year limited; GS Ultra
Flex Rim: five-year limited; GS Collegiate Breakaway Rim: five-year limited; Double Ring Static Galvanized Rim: Unconditional Lifetime
Padding Warranty: Multi-Purpose Backboard Edge Padding: one-year limited; Indoor Backboard Edge Padding: five-year limited (indoor
only); Custom Fitted Pole Padding: one-year limited; Wrap Around Pole Padding: one-year limited
NOT COVERED BY THIS WARRANTY
• Use in non-residential applications of Glass backboards on Signature Series systems.
• Use in non-residential applications of Extreme Series and Tournament Series complete systems.
• Any products subjected to abuse, negligence, improper installation, vandalism, acts of God, alteration of product or any other events
beyond the control of Goalsetter Systems.
• Paint or rusted parts. Touch-up paint is included in all hardware kits.
• Deterioration of product due to time or wear and tear.
Normal deterioration of products due to atmospheric conditions, weather, wear and tear (including paint), or other causes that do not affect
functional use are not covered by Goalsetter Systems warranties. All warranties are valid only when product is used in the intended
application & when installed according to Goalsetter Systems instructions. Warranty may be void if maintenance instructions in the
Owner’s Manual are not followed. If you did not receive an Owners Manual please call 1-800-362-4625 and one will be mailed to you.
WARRANTY CLAIMS: All returns must be arranged through the Goalsetter Systems dealer where the product was originally purchased.
Warranties do not cover dealer service charges, labor charges, freight charges and travel expenses associated with replacement, repair or
removal of warranty item. A Goalsetter Warranty Claim form must be completed, and photos submitted, for any item you wish to claim
under warranty. If the purchase was not made through a dealer, this form is available by email, fax or mail. In response to your claim, you
will receive an order confirmation as well as a notice stating whether Goalsetter needs your warranty item returned. Goalsetter will notify
you by fax or phone if we determine that the item cannot be claimed under warranty. Goalsetter Systems is not responsible for any
charges for labor to install or repair defective product without prior authorization. Goalsetter will determine the most economical
method to either repair or replace product before any work is to commence.
MISC PRODUCT WARRANTIES
Other Portable Systems: GS4500 – 5 year limited; GS5000 – Base – 10 year limited, Pole, Backboard, Hand Crank, Padding and Rim – 5
year limited; Gs6000 & GS7000 – Portable Structure – 10 year limited, Backboard – Lifetime limited, Padding and Rim – 5 year limited
Playground Structures: All GS MAX & GS Double MAX Systems – Unconditional Lifetime Functional Warranty; RP775 3-1/2" Gooseneck
Pole – 10 year limited; RP776 3-1/2" Adjustable Pole – 10 year limited; RP777 4-1/2" Gooseneck Pole – 25 year limited; RP778 4-1/2"
Adjustable Pole – 25 year limited; RP780 Mega Duty Pole – Lifetime limited.
Gym Structures & Accessories: Stationary, Side Fold and Swing Up Wall Mounted Structures – Lifetime limited; Height Adjuster – 10 year
limited; A11067 Wall Mount Power Winch – 5 year limited; A11068 Portable 110 Volt Winch – 1 year limited; A11008 Fail-Safe Structure
Catch – 10 year limited; A11200 Easy-Up Youth Mini Goal – 1 year limited on structure and rim, Lifetime limited on backboard
Rims & Nets: R10126 Single Ring Static – 2 year limited; R10226 Double Ring Static – Unconditional Lifetime; R10326 Heavy Duty Reflex
– 2 year limited; R10426 GS Ultra Flex – 5 year limited; R10554 GS Collegiate Breakaway – 5 year limited; R10654 GS Pro Breakaway –
5 year limited; R10834 Home Court Reflex – 1 year limited; R10935 GS Premier Breakaway – 5 year limited; A11013 Steel Net – 2 year
limited
Institutional Backboards: CB4272RG 42x72 Competition Glass – Unconditional LIfetime (indoor only); CB4272RGCV 42x72 Competition
Glass Conversion – Unconditional Lifetime (indoor only); CB4872RG 48x72 Rectangular Glass – 20 year limited (indoor only); RB4254GC
42x54 Glass Conversion – Unconditional Lifetime (indoor only); CB3954 FG Fan-Shaped Glass – Unconditional Lifetime (indoor only);
RB4260RS 42x60 Rectangular Steel – 10 year limited; RB3954RS 39x54 Rectangular Steel – 10 year limited; RB3954FS 39x54 Fan Steel -
10 year limited; RB3954RA 39x54 Rectangular White Aluminum – Lifetime warranty on direct mount pole systems; RB3654FCA 36x54 Fan
Cast Aluminum – Lifetime warranty on direct mount pole systems, otherwise 10 year limited; RB3654FA 36x54 Fan White Aluminum –
Lifetime warranty on direct mount pole systems, otherwise 10 year limited; RB4272RF 42x72 Rectangular Fiberglass – 10 year limited;
RB4254RP 42x54 Rectangular Polycarbonate – Lifetime limited; RB4254RG 42x54 Rectangular Glass – Lifetime limited; RB3954 FP 39x54
Fan Polyethylene – Lifetime limited
WARRANTIES