Goalsetter Systems Junior Hoop User manual

J
JU UN NI IO OR RH HO OO OP P
IInntteerrnnaallJJaacckkAAddjjuussttaabbllee
HHeeiigghhttGGooaallSSyysstteemm
MMaaddeeIInnTThheeUUSSAA
IInnssttaallllaattiioonn
&&OOwwnneerr’’ss
IInnssttrruuccttiioonnss

J
Ju un ni io or rH Ho oo op pI In nt te er rn na al lJ Ja ac ck kS Sy ys st te em mI In ns st tr ru uc ct ti io on ns s
This manual explains the proper
installation, operation and maintenance of
your Goalsetter Goal. Study and
understand these instructions thoroughly
before installing or operating the goal.
Failure to do so could result in serious
injury or death and/or equipment damage.
Consult your Goalsetter dealer or
Goalsetter Systems, Inc. if you do not
understand the instructions in this manual
or need additional information.
Goalsetter Systems, Inc. recommends that
you retain this manual for future reference
of operation, maintenance and parts
information.
The instructions, illustrations and
specifications in this manual are based on
the latest information available at the time
of publication. Your goal may have product
improvements and options not yet
contained in this manual.
Goalsetter Systems, Inc. reserves the right
to make changes at any time without
notice or obligation.
Additional copies of these instructions are
available from Goalsetter Systems, Inc.
22wwwwww..ggooaallsseetttteerrssyysstteemmss..ccoomm880000..336622..GGOOAALL((44662255))
GOALSETTER®, GOALSETTER SYSTEMS®AND GOALSETTER®logo
are all registered trademarks of Goalsetter Systems, Inc. in the U.S.
and/or other countries.
GS™and BEST IN BASKETBALL™are trademarks of Goalsetter
Systems, Inc.
This product is covered by various U.S. and Canadian patents,
including U.S. Patent #5,211,393.
Patent infringement will be prosecuted.
No part of this manual may be reproduced in any form or by any
means electronic or mechanical, including photocopying, recording,
or by any information storage and retrieval systems without the
express written consent of Goalsetter Systems, Inc.
C
Co op py yr ri ig gh ht t2 20 00 06 6. .
R
Re ev vi is se ed d1 12 2/ /2 22 2/ /2 20 00 08 8. .
A
Al ll lR Ri ig gh ht ts sR Re es se er rv ve ed d. .
G
Go oa al ls se et tt te er rS Sy ys st te em ms s, ,I In nc c. .
QQuueessttiioonnss??CCoommmmeennttss??CCoonnttaaccttUUss::
PPhhoonnee::880000..336622..44662255••FFaaxx::664411..559944..33334433
EEmmaaiill::iinnffoo@@ggooaallsseetttteerrssyysstteemmss..ccoomm
wwwwww..ggooaallsseetttteerrssyysstteemmss..ccoomm

J
Ju un ni io or rH Ho oo op pI In nt te er rn na al lJ Ja ac ck kS Sy ys st te em mI In ns st tr ru uc ct ti io on ns s
T
TA AB BL LE EO OF FC CO ON NT TE EN NT TS S
C
Co on nt ta ac ct tI In nf fo or rm ma at ti io on n. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
S
Sa af fe et ty yI In ns st tr ru uc ct ti io on ns s. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
G
Go oa al lS Sp pe ec ci if fi ic ca at ti io on ns s. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
G
Go oa al lA As ss se em mb bl ly y. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Required Tools and Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Hardware Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6
Parts List – Mini Hoop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-9
Pole Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Backboard Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Goal Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Rim Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Height Indicator Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Permanent Crank Handle Attachment . . . . . . . . . . . . . . . . . . . . . . . .13
O
Op pe er ra at ti io on na an nd dM Ma ai in nt te en na an nc ce e. . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-15
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
W
Wa ar rr ra an nt ti ie es s. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
880000..336622..GGOOAALL((44662255))wwwwww..ggooaallsseetttteerrssyysstteemmss..ccoomm33
TThhaannkkyyoouuaannddccoonnggrraattuullaattiioonnssffoorrppuurrcchhaassiinnggaaGGooaallsseetttteerrGGooaall––tthheeffiinneesstt
bbaasskkeettbbaallllggooaallssyysstteemmoonntthheemmaarrkkeettttooddaayy!!You will discover that Goalsetter is
unsurpassed in product innovation, quality and integrity in the basketball
equipment industry. We are continually focused on designing, engineering and
producing products that meet and exceed the expectations of today’s toughest
playing environments and demanding players.
T
TH HA AN NK KY YO OU U! !

J
Ju un ni io or rH Ho oo op pI In nt te er rn na al lJ Ja ac ck kS Sy ys st te em mI In ns st tr ru uc ct ti io on ns s
44wwwwww..ggooaallsseetttteerrssyysstteemmss..ccoomm880000..336622..GGOOAALL((44662255))
FFaaiilluurreettooffoolllloowwtthheesseessaaffeettyyiinnssttrruuccttiioonnssmmaayyrreessuullttiinn
sseerriioouussiinnjjuurryyoorrddeeaatthhaanndd//oorrpprrooppeerrttyyddaammaaggee..
••Do not install or use this product unless the instructions
within this manual have been carefully read and
understood.
••Consult your Goalsetter dealer or Goalsetter Systems,
Inc. if you do not understand the instructions in this
manual or need additional information.
••Before digging for the ground anchor, contact your local
One-Call system in your area.
••Installation and assembly of this product will require
lifting and bending that may result in injury to anyone
not accustom to this type of activity.
••Climate, corrosion or misuse could result in system
failure.
••DO NOT HANG on the rim or any part of the goal
system. This includes the backboard, support braces or
net.
••During play, especially when performing dunking
activities, keep the player’s face away from the backboard, rim and net. Serious injury could result
if teeth/face come in contact with the backboard, rim or net. Do not wear jewelry or other loose
objects that could become entangled in the net.
••Twice yearly, check the goal system for loose hardware, excessive wear and signs of corrosion.
Repair the system before use.
••Never play on damaged equipment.
S
SA AF FE ET TY YI IN NS ST TR RU UC CT TI IO ON NS S
G
GO OA AL LA AS SS SE EM MB BL LY Y
I
IM MP PO OR RT TA AN NT T: :Safe assembly of the goal requires two to three people in
good physical condition and capable of lifting 80-100 lbs (36-45 kg) each.
I
IM MP PO OR RT TA AN NT T: :Locate and familiarize yourself with all parts of the goal
before beginning assembly.
Level
Rubber Mallet
12' Tape Measure
Phillips Screwdriver
Ratchet
9/16" and 3/4" Sockets
9/16" and 3/4" Wrenches
R
Re eq qu ui ir re ed dT To oo ol ls sa an nd dM Ma at te er ri ia al ls s

J
Ju un ni io or rH Ho oo op pI In nt te er rn na al lJ Ja ac ck kS Sy ys st te em mI In ns st tr ru uc ct ti io on ns s
880000..336622..GGOOAALL((44662255))wwwwww..ggooaallsseetttteerrssyysstteemmss..ccoomm55
H
HA AR RD DW WA AR RE EI ID DE EN NT TI IF FI IC CA AT TI IO ON N
RRiimmBBoollttAAsssseemmbbllyy
D
De es sc cr ri ip pt ti io on nM Mo od de el lP Pa ar rt ts sL Li is st tL Le en ng gt th h
C
Ca al ll lo ou ut t
Backboard Bolt Mini Hoop #10 2"
GGrroouunnddAAnncchhoorrBBoolltt
33aa33bbaabbbbcc
1133aa1133bb1133cc
JJaacckkHHaannddllee
55bb
55aa
R
Re ef fe er rt to op pa ag ge es s8 8- -9 9f fo or rd de es sc cr ri ip pt ti io on ns s, ,
m
mo od de el lu us sa ag ge ea an nd dq qu ua an nt ti it ti ie es s. .
1133dd
EExxtteennssiioonnAArrmmTTooPPoolleePPiivvoottPPiinnAAsssseemmbbllyy––11//22""ddiiaa..xx66--11//22""
66bb66aa66bb

J
Ju un ni io or rH Ho oo op pI In nt te er rn na al lJ Ja ac ck kS Sy ys st te em mI In ns st tr ru uc ct ti io on ns s
66wwwwww..ggooaallsseetttteerrssyysstteemmss..ccoomm880000..336622..GGOOAALL((44662255))
H
HA AR RD DW WA AR RE EI ID DE EN NT TI IF FI IC CA AT TI IO ON N
JJaacckk--TToo--EExxtteennssiioonnAArrmmPPiivvoottPPiinnAAsssseemmbbllyy
88bb88aa88bb
88cc
D
O
W
N
U
P
345
1144
GGrroommmmeett
1155
UUpp--DDoowwnnDDeeccaall
1166
11//88""HHeexxKKeeyy
55//6644""HHeexxKKeeyy
55//3322""HHeexxKKeeyy
BBllaacckkTToouucchh--UUpp
PPaaiinntt
HHeeiigghhtt
IInnddiiccaattoorrDDeeccaall

D*
J
Ju un ni io or rH Ho oo op pI In nt te er rn na al lJ Ja ac ck kS Sy ys st te em mI In ns st tr ru uc ct ti io on ns s
880000..336622..GGOOAALL((44662255))wwwwww..ggooaallsseetttteerrssyysstteemmss..ccoomm77
G
GO OA AL LS SP PE EC CI IF FI IC CA AT TI IO ON NS S
C
A
B
E
F
G
H
Playing Surface
JJuunniioorrHHoooopp
Pole Size............................................3" x 3"
Backboard Size ............................25" x 36"
Weight with Glass ............................111 lbs.
Height Range (A) ................................3' – 5'
Extension Distance (B) at ..................3': 24"
....................................................4': 27-3/4"
....................................................5': 27-1/2"
Rim to Top-of-Goal Distance (C) ............20"
Crank Distance (D) ....................................9"
Crank Height (E) ......................................16"
Offset Height (F) ..............................42-1/4"
Pole Height (G) ................................62-3/4"
Offset Distance (H)..................................12"

J
Ju un ni io or rH Ho oo op pI In nt te er rn na al lJ Ja ac ck kS Sy ys st te em mI In ns st tr ru uc ct ti io on ns s
88wwwwww..ggooaallsseetttteerrssyysstteemmss..ccoomm880000..336622..GGOOAALL((44662255))
1111
P
PA AR RT TS SL LI IS ST T– –J JU UN NI IO OR RH HO OO OP P
22
NNOOTTEE::Refer to page 15
for parts descriptions.
NNOOTTEE::Refer to page
9-11 for hardware descriptions. BBaacckkbbooaarrdd
AAsssseemmbbllyy
PPoollee
11
GGrroouunndd
AAnncchhoorr
44
JJaacckk
AAsssseemmbbllyy
33HHaarrddwwaarree
11221133
RRiimm&&NNeett
AAsssseemmbbllyy
aannddHHaarrddwwaarree
1100HHaarrddwwaarree
(4 places)
99
UUppppeerr
EExxtteennssiioonnAArrmm
1144
HHeeiigghhttDDeeccaall
&&GGrroommmmeett
1155
HHaarrddwwaarree
66
1166
UUpp--DDoowwnnDDeeccaall
(backside)
55
JJaacckkHHaannddllee
77
LLoowweerr
EExxtteennssiioonnAArrmm
88
HHaarrddwwaarree

J
Ju un ni io or rH Ho oo op pI In nt te er rn na al lJ Ja ac ck kS Sy ys st te em mI In ns st tr ru uc ct ti io on ns s
880000..336622..GGOOAALL((44662255))wwwwww..ggooaallsseetttteerrssyysstteemmss..ccoomm99
P
PA AR RT TS SD DE ES SC CR RI IP PT TI IO ON N
RREEFFMMIINNIIHHOOOOPPDDEESSCCRRIIPPTTIIOONN
111 Ground Anchor
221 Pole – 3" x 3"
33aa5 Bolt, 1/2"-13 UNC x 1-1/4"
33bb5 Lock Washer, 1/2"
441 Jack Assembly
55aa1 Jack Handle
55bb2 8-32 Setscrew
66aa2 1/2" dia. x 6-1/2" Pivot Pin
66bb4 1/2" I.D. Set Collar
771Lower Extension Arm
88aa1 5/8" dia. x 1-5/16" Pivot Pin
88bb2Fender Washer, 1-1/2" OD x 5/16"
88cc2Socket Screw, 1/4"-20 x 1/2" SS BH
991Upper Extension Arm
1100aa4 Bolt, 3/8"-13 UNC x 2"
1100bb8 3/8" Flat Washer
1100cc43/8" Locknut
11111 Backboard Assembly, 25" x 36"
11221Rim and Net Assembly
1133aa4 Bolt, 3/8"-16 UNC x 2"
1133bb8Flat Washer, 3/8"
1133cc4Lock Washer, 3/8"
1133dd4Flange Nut, 3/8"-16 UNC
11441 Decal, Height Indicator
11551 Grommet
11661Decal, Up–Down

J
Ju un ni io or rH Ho oo op pI In nt te er rn na al lJ Ja ac ck kS Sy ys st te em mI In ns st tr ru uc ct ti io on ns s
1100wwwwww..ggooaallsseetttteerrssyysstteemmss..ccoomm880000..336622..GGOOAALL((44662255))
P
PO OL LE EA AS SS SE EM MB BL LY Y
SStteepp11::Remove five plastic plugs from threaded
holes in ground anchor.
NNOOTTEE::Use protective padding to protect pole finish.
SStteepp22::Unpack pole and jack.
NNOOTTEE: On the all models, the jack assembly is
already installed in the pole.
SStteepp33::Locate five 1/2" x 1-1/4" bolts 11(#3 in
parts list). Prepare them for use by having lock
washer 22slipped on as shown.
SStteepp44::Fasten pole 33to threaded ground anchor
plate 44as follows:
•First, install and tighten three back bolts 55with
lock washers.
•Then, install and tighten two front bolts 66with
lock washers.
SStteepp55::Fully tighten five bolts.
IIMMPPOORRTTAANNTT::The bolts must pass all the way
through the ground anchor plate. If they are
recessed within the plate when fully tightened,
please contact Goalsetter Systems.
SStteepp66::Pull jack assembly 77out slightly, remove
packing and protective materials from end of jack
and reposition jack in pole.
SStteepp77::Insert crank handle through access hole
and slide onto shaft.
NNOOTTEE::If a permanent crank handle installation is
desired, refer to Permanent Crank Handle
Attachment.
SStteepp88::Position lower extension arm 88with clevis
99toward pole offset. Align lower extension arm
pivot holes with lower holes 1100in pole.
1122
111188
1100
99
77
1122
Both Sides 33
44
66
55

J
Ju un ni io or rH Ho oo op pI In nt te er rn na al lJ Ja ac ck kS Sy ys st te em mI In ns st tr ru uc ct ti io on ns s
880000..336622..GGOOAALL((44662255))wwwwww..ggooaallsseetttteerrssyysstteemmss..ccoomm1111
SStteepp99::Attach lower extension arm to pole
using the following:
M
Mi in ni iH Ho oo op p: :1/2" x 6-1/2" pin and two lock collars
(#6 in parts list). Tighten with 1/8" hex key
(provided).
SStteepp1100::Attach upper extension arm 1111
pivot holes with upper holes 1122in pole.
Attach arm to pole using the following:
M
Mi in ni iH Ho oo op p: :1/2" x 6-1/2" pin and two lock collars
(#6 in parts list). Tighten with 1/8" hex key (provided).
SStteepp1111::Attach upper mount of jack to lower extension arm using the following:
M
Mi in ni iH Ho oo op p: :5/8" x 1-5/16" pin, two fender washers, and two 1/2" socket screws (#8 in
parts list). Tighten with 5/32" hex key (provided).
P
PO OL LE EA AS SS SE EM MB BL LY Y( (c co on nt t. .) )
1122
111188
1100
99
B
BA AC CK KB BO OA AR RD DA AT TT TA AC CH HM ME EN NT T
SStteepp11::Open lid of box
containing backboard 11and
position the backboard (without
removing it from box) face down
under lower extension arm 22
with rim mounting plate 33
toward pole.
NNOOTTEE::Backboards are attached
to extension arms using the
following:
MMiinniiHHoooopp::Four 3/8" x 2" bolts,
eight flat washers and four locknuts
(#10 in parts list).
HHaarrddwwaarreeSSeeqquueennccee::Bolt passes through flat
washer - arm bracket - backboard bracket -
flat washer - locknut.
SStteepp22::Align lower backboard holes
44with lloowweerrextension arm holes 22.
Attach backboard to arm using
hardware noted above.
SStteepp33::Align upper backboard holes
55with uuppppeerrextension arm holes 66.
Attach backboard to arm using
hardware noted above.
NNOOTTEE::JJuunniioorrHHoooopp::Do not over
tighten. Snug tighten only.
11
33
6655
44
22

J
Ju un ni io or rH Ho oo op pI In nt te er rn na al lJ Ja ac ck kS Sy ys st te em mI In ns st tr ru uc ct ti io on ns s
1122wwwwww..ggooaallsseetttteerrssyysstteemmss..ccoomm880000..336622..GGOOAALL((44662255))
R
RI IM MA AT TT TA AC CH HM ME EN NT T
44
11
22
33
SStteepp11::Remove any cardboard edge protectors
and protective sheeting from backboard.
NNOOTTEE::Four steel shouldered bushings 1 1are
factory installed. If loose, make sure to have them
seated properly when tightening rim bolts. If
missing, contact Goalsetter or dealer to get
replacements. D
DO ON NO OT Ti in ns st ta al ll lr ri im mw wi it th ho ou ut t
b
bu us sh hi in ng gs s. .
IIMMPPOORRTTAANNTT::Correct sequence of hardware
installation MUST be followed during assembly.
SStteepp22::Loosely attach rim 4 4to backboard
through top mounting holes 2
2with two 3/8" x 2"
bolts (#13 in parts list), four flat washers, two lock
washers and two nuts. Snug tighten hardware – a
9/16" open-end wrench may be necessary.
H
Ha ar rd dw wa ar re eS Se eq qu ue en nc ce e: :Bolt passes through flat washer - rim
backplate - backboard bushing - backboard mounting plate -
flat washer - lock washer - nut.
SStteepp33::Repeat procedure outlined in Step 2 for
lower rim mounting holes 3
3.
SStteepp44::Level rim side to side and then fully tighten
hardware.
SStteepp55::Attach net to rim.
G
GO OA AL LA AL LI IG GN NM ME EN NT T
S
St te ep p1 1: :Check goal assembly with a level and inspect visually to
determine if it is parallel and plumb to playing surface.
S
St te ep p2 2: :If adjustments are necessary, slightly loosen bolts to rotate goal
or place shims between pole plate and ground anchor plate.

J
Ju un ni io or rH Ho oo op pI In nt te er rn na al lJ Ja ac ck kS Sy ys st te em mI In ns st tr ru uc ct ti io on ns s
880000..336622..GGOOAALL((44662255))wwwwww..ggooaallsseetttteerrssyysstteemmss..ccoomm1133
H
HE EI IG GH HT TI IN ND DI IC CA AT TO OR RA AT TT TA AC CH HM ME EN NT T
P
PE ER RM MA AN NE EN NT TC CR RA AN NK KH HA AN ND DL LE EA AT TT TA AC CH HM ME EN NT T
S
St te ep p1 1: :Position top of rim 3' above
playing surface using crank handle.
Measure distance with a tape measure
for accuracy.
S
St te ep p2 2: :Insert height decal 1 1with
printed number ‘3’ through indicator
hole in pole and attach to internal height
indicator plate.
S
St te ep p3 3: :Repeat steps for 4', and 5' rim
heights. Use height decals with printed
numbers ‘4’ and ‘5’.
S
St te ep p4 4: :Install rubber grommet 2 2into
indicator hole.
S
St te ep p5 5: :Attach UP/DOWN decal 3 3to
pole above crank handle hole.
S
St te ep p1 1: :Insert shoulder bolt jack shaft
extension 4
4into tapped hole on jack
shaft. Tighten with 1/8" hex key
(provided).
S
St te ep p2 2: :Attach handle 5 5to shaft using
set screws 6
6and 5/64" hex key
(provided).
33
66
66
55
11
22
44

J
Ju un ni io or rH Ho oo op pI In nt te er rn na al lJ Ja ac ck kS Sy ys st te em mI In ns st tr ru uc ct ti io on ns s
1144wwwwww..ggooaallsseetttteerrssyysstteemmss..ccoomm880000..336622..GGOOAALL((44662255))
O
OP PE ER RA AT TI IO ON N
11
22
2
2Height Indicator indicates goal
height from 3' to 5'.
The exterior finish of your Goalsetter goal is designed for outdoor
environments and should only require periodic cleaning and inspection for
imperfections that could develop over time (see Maintenance section).
When cleaning is necessary, Goalsetter recommends using water and a mild
dish detergent applied with a soft, non-abrasive cloth.
IIMMPPOORRTTAANNTT::DO NOT use abrasive cleaners to clean the goal. Damage to
the finish may result.
C
CL LE EA AN NI IN NG G
1
1Crank – Turn clockwise for goal to go
up, turn counter clockwise for goal to go
down.

J
Ju un ni io or rH Ho oo op pI In nt te er rn na al lJ Ja ac ck kS Sy ys st te em mI In ns st tr ru uc ct ti io on ns s
880000..336622..GGOOAALL((44662255))wwwwww..ggooaallsseetttteerrssyysstteemmss..ccoomm1155
Goalsetter uses a two-part acrylic-enamel paint on our
goals. With periodic inspection and service when
needed, the high-gloss finish is designed to last for
many years. A small bottle of black paint with brush is
provided with every goal for touch up of imperfections
as they develop and can be found in the hardware kit.
If more touch up is required, please contact Goalsetter
Systems, Inc. or your local Goalsetter Dealer.
M
MA AI IN NT TE EN NA AN NC CE E
L
LU UB BR RI IC CA AT TI IO ON N
11
11Jack Assembly
TThheeJJuunniioorrHHooooppiisseeqquuiippppeeddwwiitthhaa
lluubbrriiccaattiioonnppoorrtt. Use a liberal amount of
general-purpose lubricating oil. DO NOT use a
penetrating oil.
IIMMPPOORRTTAANNTT– A general-purpose lubricating oil
like “3-in-1” or lightweight motor oil is
recommended. DO NOT use penetrating oil like
“WD-40”. Goalsetter has “Maintenance Kits”
available which would include a bottle of
lubricating oil. Contact Goalsetter Systems, Inc.
or your local Goalsetter Dealer for details.
Every jack that comes with a Goalsetter height-adjustable goal is pre-
lubricated as it comes from the factory. With any mechanical component,
periodic inspection and service is required. Goalsetter recommends applying
lubrication at least once or twice a year to keep a smooth operation of the
height actuator. Failure to do so could result in jack failure and not be
covered under warranty.

BUYER AGREES THAT PRODUCTS SOLD BY GOALSETTER SYSTEMS, INC. CARRY THE FOLLOWING WARRANTY
Subject to proper installation and normal, intended use, all structural components of Goalsetter Systems Signature Series*, Extreme
Series* and GS Wall-Mount Series* basketball systems are warranted to be free of defects in material and workmanship for the duration
of ownership by the original retail purchaser, subject to the limitations below. Tournament Series* systems will be covered by this
warranty for a period of five years. GS Portable Series* and Goalsetter Mini Hoop systems will be covered by this warranty for a period
of two years. Goalsetter shall have the right to require the purchaser to deliver the allegedly defective product to Goalsetter for testing,
repair or replacement. Goalsetter shall not be responsible for any expenses associated with the replacement or removal of the product
from its application for such delivery. Modification of any product by the customer, unless approved by Goalsetter Systems, will void all
warranty. Where listed as “LIMITED”, the warranties shall cover damage or failure that occurs during the course of NORMAL or
INTENDED USE of the product. Normal or intended use shall be described as activity that is necessary for the participation in the sport
for which the equipment is designed. NOT COVERED is damage caused by deliberate hanging, multiple player hanging, vandalism, non-
basketball activities or any other activity that could be regarded as abusive. *Signature Series – MVP, Captain, All-American, All-Star, Contender,
Champion; Extreme Series – X672, X660, X560, X554, X454, X448; GS Wall-Mount Series – GS72 Wall-Mount, GS60 Wall-Mount, GS54 Wall-Mount, GS48 Wall-
Mount; Tournament Series – Elite, Classic; GS Portable Series – GS1000, GS2000, GS2500, GS3000, GS3500
Any warranty on a basketball system excludes the rim. Rim warranties are as follows: Single Ring Static Rim: two-year limited;
Double Ring Static Rim: Unconditional Lifetime; Home Court Flex Rim: one-year limited; Heavy Duty Flex Rim: two-year limited; GS Ultra
Flex Rim: five-year limited; GS Collegiate Breakaway Rim: five-year limited; Double Ring Static Galvanized Rim: Unconditional Lifetime
Padding Warranty: Multi-Purpose Backboard Edge Padding: one-year limited; Indoor Backboard Edge Padding: five-year limited (indoor
only); Custom Fitted Pole Padding: one-year limited; Wrap Around Pole Padding: one-year limited
NOT COVERED BY THIS WARRANTY
• Use in non-residential applications of Glass backboards on Signature Series systems.
• Use in non-residential applications of Extreme Series and Tournament Series complete systems.
• Any products subjected to abuse, negligence, improper installation, vandalism, acts of God, alteration of product or any other events
beyond the control of Goalsetter Systems.
• Paint or rusted parts. Touch-up paint is included in all hardware kits.
• Deterioration of product due to time or wear and tear.
Normal deterioration of products due to atmospheric conditions, weather, wear and tear (including paint), or other causes that do not affect
functional use are not covered by Goalsetter Systems warranties. All warranties are valid only when product is used in the intended
application & when installed according to Goalsetter Systems instructions. Warranty may be void if maintenance instructions in the
Owner’s Manual are not followed. If you did not receive an Owners Manual please call 1-800-362-4625 and one will be mailed to you.
WARRANTY CLAIMS: All returns must be arranged through the Goalsetter Systems dealer where the product was originally purchased.
Warranties do not cover dealer service charges, labor charges, freight charges and travel expenses associated with replacement, repair or
removal of warranty item. A Goalsetter Warranty Claim form must be completed, and photos submitted, for any item you wish to claim
under warranty. If the purchase was not made through a dealer, this form is available by email, fax or mail. In response to your claim, you
will receive an order confirmation as well as a notice stating whether Goalsetter needs your warranty item returned. Goalsetter will notify
you by fax or phone if we determine that the item cannot be claimed under warranty. Goalsetter Systems is not responsible for any
charges for labor to install or repair defective product without prior authorization. Goalsetter will determine the most economical
method to either repair or replace product before any work is to commence.
MISC PRODUCT WARRANTIES
Other Portable Systems: GS4500 – 5 year limited; GS5000 – Base – 10 year limited, Pole, Backboard, Hand Crank, Padding and Rim – 5
year limited; Gs6000 & GS7000 – Portable Structure – 10 year limited, Backboard – Lifetime limited, Padding and Rim – 5 year limited
Playground Structures: All GS MAX & GS Double MAX Systems – Unconditional Lifetime Functional Warranty; RP775 3-1/2" Gooseneck
Pole – 10 year limited; RP776 3-1/2" Adjustable Pole – 10 year limited; RP777 4-1/2" Gooseneck Pole – 25 year limited; RP778 4-1/2"
Adjustable Pole – 25 year limited; RP780 Mega Duty Pole – Lifetime limited.
Gym Structures & Accessories: Stationary, Side Fold and Swing Up Wall Mounted Structures – Lifetime limited; Height Adjuster – 10 year
limited; A11067 Wall Mount Power Winch – 5 year limited; A11068 Portable 110 Volt Winch – 1 year limited; A11008 Fail-Safe Structure
Catch – 10 year limited; A11200 Easy-Up Youth Mini Goal – 1 year limited on structure and rim, Lifetime limited on backboard
Rims & Nets: R10126 Single Ring Static – 2 year limited; R10226 Double Ring Static – Unconditional Lifetime; R10326 Heavy Duty Reflex
– 2 year limited; R10426 GS Ultra Flex – 5 year limited; R10554 GS Collegiate Breakaway – 5 year limited; R10654 GS Pro Breakaway –
5 year limited; R10834 Home Court Reflex – 1 year limited; R10935 GS Premier Breakaway – 5 year limited; A11013 Steel Net – 2 year
limited
Institutional Backboards: CB4272RG 42x72 Competition Glass – Unconditional LIfetime (indoor only); CB4272RGCV 42x72 Competition
Glass Conversion – Unconditional Lifetime (indoor only); CB4872RG 48x72 Rectangular Glass – 20 year limited (indoor only); RB4254GC
42x54 Glass Conversion – Unconditional Lifetime (indoor only); CB3954 FG Fan-Shaped Glass – Unconditional Lifetime (indoor only);
RB4260RS 42x60 Rectangular Steel – 10 year limited; RB3954RS 39x54 Rectangular Steel – 10 year limited; RB3954FS 39x54 Fan Steel -
10 year limited; RB3954RA 39x54 Rectangular White Aluminum – Lifetime warranty on direct mount pole systems; RB3654FCA 36x54 Fan
Cast Aluminum – Lifetime warranty on direct mount pole systems, otherwise 10 year limited; RB3654FA 36x54 Fan White Aluminum –
Lifetime warranty on direct mount pole systems, otherwise 10 year limited; RB4272RF 42x72 Rectangular Fiberglass – 10 year limited;
RB4254RP 42x54 Rectangular Polycarbonate – Lifetime limited; RB4254RG 42x54 Rectangular Glass – Lifetime limited; RB3954 FP 39x54
Fan Polyethylene – Lifetime limited
W
WA AR RR RA AN NT TI IE ES S
2200wwwwww..ggooaallsseetttteerrssyysstteemmss..ccoomm880000..336622..GGOOAALL((44662255))