Goalsetter Systems GS72 User manual

GS Baseline Series
Wall-Mounted Goal Systems
t(4
t(4
t(4
InstallatIon and
owner’s InstrUCtIons
table of Contents
Safety Instructions............................................... 2
Goal Specifications .............................................. 3
Determine Installation Specifications................... 3
Parts List – GS72, GS60 & GS54........................ 4
Frame Attachment................................................ 5
Backboard Attachment......................................... 5
Rim Attachment ................................................... 6
Ready to Play....................................................... 7
Warranties.............................................Back Cover

Safety Instructions
Owner must ensure that all installers and players know and comply
with these rules for safe assembly, installation, operation and use
of the system. Proper and complete assembly, use and supervision
is essential for proper operation of the product and to reduce
the risk of accident or injury. DO NOT ATTEMPT TO ASSEMBLE
AND INSTALL THIS PRODUCT WITHOUT FOLLOWING THE
INSTRUCTIONS CAREFULLY.
WARNING
1. Failure to follow these instructions may result in death, serious
injury and/or property damage and will void the warranty. Do
not install or use this product unless the instructions within this
manual have been carefully read and understood.
2. Locate your goal away from potential dangers, including trip
hazards, high-traffic areas or where a vehicle might come into
contact with backboard or rim.
3. To avoid severe injury or death, do not locate goal under power
lines that may come into contact with the goal as it is raised.
Power lines should not be within 20 ft. radius of goal.
4. Two or three people in good physical condition and capable of
lifting at least 90-100 lbs. (40-45 kg) each are recommended
for safe installation and assembly.
5. Walls can contain electrical wires and other unseen hazards and
obstacles. It is the installer’s responsibility to locate and avoid
these hazards during installation.
t*GVTJOHBMBEEFSEVSJOHBTTFNCMZVTFFYUSFNFDBVUJPO'PMMPXBMM
warnings and cautions on the ladder carefully.
t*OTUBMMBUJPOBOEBTTFNCMZPGUIJTQSPEVDUXJMMSFRVJSFMJGUJOHBOE
bending that may result in injury to anyone not accustomed to
this type of activity.
t&OTVSFUIFSFBSFOPPWFSIFBEQPXFSMJOFTXJUIJOBGUN
radius of the goal location.
t$MJNBUFDPSSPTJPOPSNJTVTFDPVMESFTVMUJOTZTUFNGBJMVSF
t0OMZVTFQBSUTQSPWJEFEXJUIZPVS(PBMTFUUFS®basketball goal
system or replacement parts provided by Goalsetter Systems,
Inc. Use of other parts (a) may cause the goal system to fail,
(b) could result in death, serious injury or property damage, and
(c) will void the warranty.
t8JUISJNTFUBUwQMBZJOHIFJHIUUIFNJOJNVNPQFSBUJPOBM
IFJHIUJTwNUPUIFCPUUPNPGUIFCBDLCPBSE
tDO NOT CLIMB OR HANG on the rim or any part of the goal
system. This includes the backboard, support braces and net.
The product is not designed for such use and property damage
or personal injuries such as cuts, broken bones, nerve, spinal
cord or brain injury or death could occur.
t6TFDBVUJPOXIFOQFSGPSNJOHEVOLJOHBDUJWJUJFTXJUIUIJTQSPEVDU
t%VSJOHQMBZLFFQQMBZFSTGBDFTBXBZGSPNUIFCBDLCPBSESJNBOE
net or serious injury could result.
t1MBZFSTNVTUXFBSBNPVUIHVBSEUPBWPJEEFOUBMJOKVSJFT
t%POPUXFBSKFXFMSZSJOHTXBUDIFTOFDLMBDFTFUDPSPUIFS
loose objects that could become tangled in the net or injure
another player.
t
#FGPSFFBDIVTFDIFDLUIFHPBMTZTUFNGPSMPPTFIBSEXBSFFYDFT-
sive wear and signs of corrosion. Repair the system before use.
tNEVERQMBZPOEBNBHFEFRVJQNFOU
t$IFDLUIFHPBMTZTUFNGSFRVFOUMZGPSTJHOTPGDPSSPTJPO3FNPWF
TVSGBDFSVTUBOEMPPTFQBJOUDPNQMFUFMZBOESFQBJOUXJUIFYUFSJPS
enamel paint. If rust or corrosion has penetrated or pitted any
components of the goal, DO NOT allow play and repair or replace
parts immediately.
t%0/05VTFUIFHPBMTZTUFNUPMJGUPSIPJTUBOZUIJOH
t6TFDBVUJPOXIFOVTJOHUIJTHPBMTZTUFN.PTUJOKVSJFTBSF
caused by misuse and/or not following these instructions.
IMPORTANT
&ODMPTFEVOEFSOFBUIUIFQSPUFDUJWFTIFFUJOHPOZPVSCBDLCPBSE
JTBXBSSBOUZSFHJTUSBUJPODBSE:06.645'*--065"/%
."*-*/5)*4$"3%*/03%&350)"7&"7"-*%8"33"/5:
You may also fill out a warranty registration online at
www.goalsetter.com.
Retain this manual for future reference of operation, maintenance
and parts information.
The information in this manual is based on the latest information
available at the time of publication. Your goal may have product
improvements and options not yet contained in this manual.
Goalsetter Systems, Inc. reserves the right to make changes at any
time without notice or obligation.
$POUBDUUIFNBOVGBDUVSFSJGUFDIOJDBMBTTJTUBODFJTSFRVJSFE
Additional copies of these instructions are available from:
Goalsetter Systems, Inc.
(0"-
www.goalsetter.com

Goal Specifications
Determine Installation Location
Consider the following to determine where to install your
Goalsetter Basketball Goal:
t5IFUZQFBOETUSFOHUIPGTUSVDUVSFUPXIJDIUIFHPBMXJMM
be attached.
t8JMMCBDLCPBSEPWFSIBOHPCTUSVDUESJWFXBZPSPUIFSJNQPSUBOU
TQBDF .BYJNVNPWFSIBOHwNGSPNUIFNPVOU-
ing surface to the front of the rim.
t*TUIFSFSPPNTPWFIJDMFTCBDLJOHPVUPGESJWFXBZEPOPUTUSJLF
backboard or rim?
t8JMMDPVSUNBSLJOHTCFVTFE
t)PXNVDIQMBZJOHTVSGBDFJTOFFEFE
t)PXNVDIQMBZJOHTVSGBDFXJMMCFVOEFSUIFCBDLCPBSE
)BWJOHUIFFEHFPGUIFQMBZJOHTVSGBDFEJSFDUMZVOEFSOFBUIUIF
backboard can result in trip hazards and unpredictable ball action
following a shot. Try to have as much playing surface as possible
behind the backboard.)
t0UIFSGVODUJPOTPGQMBZJOHTVSGBDFESJWFXBZQMBZHSPVOEFUD
t8JMMUIFHPBMCFBUMFBTUGUNGSPNBOZPWFSIFBEQPXFS
lines? (No overhead power lines should be within a 20 ft. (7 m)
radius of the goal.)
Required Tools and Materials:
t-FWFM t1IJMMJQT4DSFXESJWFS
t3VCCFS.BMMFU t9/w/wBOE/w4PDLFUTBOE8SFODIFT
t5BQF.FBTVSF t8BMM'BTUFOFSTOPUJODMVEFEQSPWJEFE
t3BUDIFU CZDVTUPNFSPSJOTUBMMFS
t4UFQMBEEFS t%SJMMBOE%SJMM#JUT (masonry
if necessary)
(4 (4 (4
Backboard Size: wYw wYw wYw
Weight w/Acrylic: 162 lbs. 144 lbs. 132 lbs.
Weight w/Glass: 212 lbs. 192 lbs. 172 lbs.
")FJHIU 10’ 10’ 10’
#&YUFOTJPO%JTUBODF
7½w7½w7½w
$%JTUBODF3JNUP5PQPG(PBM 33
3/4
w29
3/4
w27
3/4
w
%$SBOL%JTUBODF — — —
&$SBOL)FJHIU — — —
')FJHIUUP#PUUPNPG'SBNF 117
3/4
w117
3/4
w117
3/4
w
('SBNF4J[F w w w
)5PQPG'SBNF)FJHIU w w w
6'-0"
19'-9"
50'-0" Optimum Inside Sidelines
15'-0"
19'-0"
25'-0"
63"
15"
12'-0"
4'-0"
Note: Lines are 2" wide.
Court Markings
(Reference Only):
Regulation Court Lengths
)JHI4DIPPM
College & Professional: 94’
IMPORTANT
Goalsetter Systems, Inc. cannot assume liability for the installation
PGBOZ8BMM.PVOUFETUSVDUVSF(PBMTFUUFS®Systems recommends
consulting a professional architect or contractor to determine a safe
wall anchoring system to match the wall construction being used in
your application.
G
)
F
B
C
A
Playing Surface

1
Frame
Parts List - GS72, GS60 & GS54 Baseline
3&' (4 (4 (4 DESCRIPTION
11 1 1 Frame
1 — — #BDLCPBSE"TTFNCMZY
— 1 — #BDLCPBSE"TTFNCMZY
— — 1 #BDLCPBSE"TTFNCMZY
B
4 4 4 5BQ#PMU6/$Y
C 'MBU8BTIFS
D 4 4 4 -PDLOVU6/$
1 1 1 Rim and Net Assembly
B 4 4 4 Bolt, 3/6/$Y
C Flat Washer, 5/" or 3/"
D 4 4 4 Nut, 3/"-16 UNC
Hardware Identification
Black Touch-Up Paint Backboard Bolt " Assembly Rim Bolt
3/8"
Assembly
5a 5b 5c
3a 3b 3b 3c
2Backboard
Assembly
4
Rim & Net
Assembly &
Hardware
5
Hardware
4 places
3

Frame Attachment
WARNING
Two or three people in good physical condition and capable of
lifting at least 90-100 lbs. (40-45 kg) each are recommended for
safe installation and assembly
.
Step 1: Unpack frame.
4UFQ Determine where to place frame on mounting
surface.
TIME OUT TIP: Use a level to make drawing
the horizontal line easier.
4UFQ Draw a 21" (533 mm) horizontal line on the mount-
JOHTVSGBDF£NNVQGSPNQMBZJOH
surface.
4UFQ Position frame 1 on wall with with bottom of frame
centered on drawn line 2 .
4UFQ Level frame horizontally and vertically using a level.
.BSLXBMMNPVOUJOHIPMFTOFFEFEGPSBUUBDINFOUPG
frame. (To be determined by customer and/or installer.)
4UFQ Set frame down.
4UFQDrill appropriate size holes as needed in mounting
surface based upon type of wall fastener being used by
customer or installer.
Step 8: Loosely attach frame to wall using correct fastener.
Step 9: Fully tighten fasteners.
Backboard Attachment
4" Typical Spacing
16"
21¼"
2½"
2
1/"
24¼
"
117¾" Up From
Playing Surface
.PVOUJOH)PMF
9/16
"
2
1
IMPORTANT
Fasteners to be determined and provided by the customer and/
or installer.
1
2
WARNING
Two or three people in good physical condition and capable of
lifting at least 90-100 lbs. (40-45 kg) each are recommended for
safe installation and assembly
.
TIME OUT TIP:-BZUIFVOPQFOFECPYXJUI
Goalsetter®logo upside down AND let the lid
open up and fold away from the goal mounting
surface.
Step 1: Lift backboard 1 into position and attach to top holes in
frame 2
t"UUBDIXJUIUXPY½" bolts (#3 in parts list), four flat
washers and two locknuts – do not fully tighten.
Hardware Sequence: Bolt passes through flat washer - frame - frame
flange - flat washer - locknut.
4UFQ Align lower backboard holes with the lower holes in
frame using same procedure and hardware as in Step 1.
4UFQ Fully tighten all fasteners.

Rim Attachment
NOTE: 6TFBMMTUFQTPGUIFGPMMPXJOHJOTUSVDUJPOTUPJOTUBMMBSFnFY
SJN5PJOTUBMMBTUBUJDSJNGPMMPXBMMTUFQTFYDFQUBOE
TIME OUT TIP: Your warranty card is located
behind protective sheeting. You MUST fill out and return
this card to activate your warranty.
Step 1: Unpack rim. Remove any cardboard edge protectors and
protective sheeting from backboard.
IMPORTANT
t'PVSCVTIJOHTBSFGBDUPSZJOTUBMMFEPOUIFCBDLCPBSE*G
loose, make sure to have them seated properly when tighten-
ing rim bolts. If missing, contact Goalsetter or dealer.
DO NOT install rim without bushings. If the bushings are
not in place, glass backboards can shatter and acrylic
backboards can crack!
t$PSSFDUTFRVFODFPGIBSEXBSFJOTUBMMBUJPOMUST be followed
during assembly.
4UFQ If not already removed, remove cover plate screws 6 and
cover plate 5 from rim assembly.
4UFQ Loosely attach rim 4 to backboard through top mount-
ing holes 2 with two
3/"
YCPMUTGPVSnBUXBTIFSUXPMPDL
washers and two nuts. Snug tighten hardware – a
9/16
"open-
end wrench may be necessary.
Hardware Sequence: Bolt passes through flat washer - rim backplate
- backboard bushing - backboard mounting plate - flat washer - lock
washer - nut.
4UFQ Repeat procedure outlined in Step 3 for lower rim mount-
ing holes 3 .
4UFQ Level rim side to side and then fully tighten hardware.
4UFQPosition cover plate 5 and attach with cover plate
screws 6 .
4UFQ Attach net to rim.
1
2
3
4
56

Ready To Play
Maintenance
5IFMJGFPGZPVSCBTLFUCBMMHPBMTZTUFNEFQFOETPONBOZWBSJBCMFT5IFDMJNBUFFYQPTVSFUPDPSSPTJWFTTVDIBTTBMUPSHBOJDNBUFSJBMT
QFTUJDJEFTPSIFSCJDJEFTBOEFYDFTTJWFVTFPSNJTVTFDBOBMMDPOUSJCVUFUPGBJMVSFPGUIFHPBMTZTUFNXIJDINBZDBVTFQSPQFSUZ
EBNBHFPSQFSTPOBMJOKVSZ#FGPSFFBDIVTFDIFDLUIFHPBMTZTUFNGPSMPPTFIBSEXBSFFYDFTTJWFXFBSBCVTFPSWBOEBMJTNPSTJHOTPG
rust or corrosion.
For safety reasons, and to prolong the life of your basketball system, you must take the following preventative measures:
t$IFDLBMMOVUTBOECPMUT*OTQFDUUIFUISFBETBOESFQMBDFJGOFDFTTBSZ*GBOZBSFMPPTFUJHIUFOUIFN
t$IFDLBMMQBSUTGPSFYDFTTJWFXFBSBOEUFBS*GOFDFTTBSZSFQMBDFBOZQBSUTUIBUIBWFCFFOXPSOPSEBNBHFEUISPVHIVTBHF
t$IFDLBMMTFDUJPOTPGUIFHPBMTZTUFNGPSWJTJCMFSVTUPSDIJQQFEPSDSBDLFEQBJOUBOEJGQSFTFOUSFQBJSBQQSPQSJBUFMZ4FF1BJOU
Touch-Up on this page.
IF RUST OR CORROSION HAS PENETRATED ANY COMPONENT, DO NOT ALLOW PLAY ON THE GOAL AND REPLACE PARTS
IMMEDIATELY.
t$POUBDU(PBMTFUUFS4ZTUFNT*ODGPSSFQMBDFNFOUQBSUT0OMZuse parts provided by Goalsetter Systems, Inc. Use of other parts (a)
may cause the goal system to fail, (b) could result in death, serious injury or property damage, and (c) will void the warranty.
t*OTQFDUUIF8BSOJOH4UJDLFSPOUIFQPMF*GJUJTSJQQFEGBEFEPSJMMFHJCMFDPOUBDU(PBMTFUUFS4ZTUFNT*ODUPSFRVFTUBSFQMBDFNFOU
Warning Sticker.
Cleaning
5IFFYUFSJPSmOJTIPGZPVS(PBMTFUUFSHPBMJTEFTJHOFEGPSPVUEPPSFOWJSPONFOUTBOETIPVMEPOMZSFRVJSFQFSJPEJDDMFBOJOHBOE
JOTQFDUJPOGPSJNQFSGFDUJPOTUIBUDPVMEEFWFMPQPWFSUJNFTFF.BJOUFOBODFTFDUJPO
When cleaning is necessary, Goalsetter recommends using water and a mild dish detergent applied with a soft, non-abrasive
cloth.
IMPORTANT
DO NOT use abrasive cleaners to clean the goal. Damage to the
finish may result.
Paint Touch-Up
Goalsetter uses a two-part acrylic-enamel paint on our goals. With periodic inspection and service when needed,
the high-gloss finish is designed to last for many years. A small bottle of black paint with brush is provided with
every goal for touch up of imperfections as they develop and can be found in the hardware kit.
*GNPSFUPVDIVQJTSFRVJSFEQMFBTFDPOUBDU(PBMTFUUFS4ZTUFNT*ODPSZPVSMPDBM(PBMTFUUFS%FBMFS

8
Warranties
IMPORTANT
&ODMPTFEVOEFSOFBUIUIFQSPUFDUJWFTIFFUJOHPOZPVSCBDLCPBSE
is a warranty registration card. YOU MUST FILL OUT AND
MAIL IN THIS CARD IN ORDER TO HAVE A VALID WARRANTY.
You may also fill out a warranty registration online at
www.goalsetter.com.
LIMITED WARRANTY
LIMITED LIFETIME WARRANTY: Subject to proper installation and normal, intended use,
and subject to the limitations set forth below, Goalsetter Systems, Inc. warrants to the
original retail purchaser that all structural components of Goalsetter Systems™ Signature
4FSJFT&YUSFNF4FSJFTBOE(48BMM.PVOU4FSJFTCBTLFUCBMMTZTUFNTBSFGSFFPG
defects in material and workmanship for the duration of ownership by such original retail
purchaser or five (5) years after discontinuation of the product by Goalsetter Systems, Inc..
4JHOBUVSF4FSJFTo.71$BQUBJO"MM"NFSJDBO"MM4UBS$POUFOEFS$IBNQJPO
&YUSFNF4FSJFTo999999
(48BMM.PVOU4FSJFTo(48BMM.PVOU(48BMM.PVOU(48BMM.PVOU(4
8BMM.PVOU
LIMITED WARRANTY: Subject to proper installation and normal, intended use, and subject
to the limitations set forth below, Goalsetter Systems, Inc. warrants to the original retail
purchaser that all structural components of (a) Goalsetter Systems™ Tournament Series
&MJUF1MVTBOE(4#BTFMJOF8BMM.PVOU4FSJFTCBTLFUCBMMTZTUFNTBSFGSFFPGEFGFDUTJO
material and workmanship for a time period of five (5) years from date of purchase
C(PBMTFUUFS4ZTUFNT+VOJPS.71BOE(4+VOJPS8BMM.PVOUCBTLFUCBMMTZTUFNTBSF
covered for a time period of two (2) years from date of purchase.
(4#BTFMJOF8BMM.PVOU4FSJFTo(4#BTFMJOF(4#BTFMJOF(4#BTFMJOF
"OZXBSSBOUZPOBCBTLFUCBMMTZTUFNFYDMVEFTUIFSJN Rim warranties are as follows:
Rims shall be free from defects in materials and workmanship from the date of purchase as
GPMMPXT34JOHMF3JOH4UBUJD3JNPOFZFBSMJNJUFEXBSSBOUZ3%PVCMF3JOH
4UBUJD3JNVODPOEJUJPOBMMJGFUJNFXBSSBOUZ3)FBWZ%VUZ#SFBLBXBZ3JNUXP
ZFBSMJNJUFEXBSSBOUZ3(4$PMMFHJBUF#SFBLBXBZ3JNPOFZFBSMJNJUFEXBSSBOUZ
Padding Warranty: Padding shall be free from defects in materials and workmanship
GSPNUIFEBUFPGQVSDIBTFBTGPMMPXT.VMUJ1VSQPTF#BDLCPBSE1BEEJOHPOFZFBSMJNJUFE
XBSSBOUZ$VTUPN'JUUFE1PMF1BEEJOHPOFZFBSMJNJUFEXBSSBOUZ8SBQ"SPVOE1PMF
Padding: one-year limited warranty.
The Limited Lifetime Warranty and the Limited Warranty shall cover damage or failure that
occurs during the course of NORMAL or INTENDED USE of the product. Normal or intended
use shall be described as activity that is necessary for the participation in the sport for
XIJDIUIFFRVJQNFOUJTEFTJHOFE NOT COVERED is damage caused by deliberate hanging,
multiple player hanging, vandalism, non-basketball activities or any other activity that
could be regarded as abusive. Goalsetter Systems5.+VOJPS.71BOE(4+VOJPS8BMM.PVOU
warranty voided if damage caused by the act of dunking.
A limited lifetime warranty is effective for the duration of ownership by the original retail
purchaser or 5 years after discontinuation of the product by Goalsetter Systems, Inc.
(PBMTFUUFS4ZTUFNT*ODTIBMMIBWFUIFSJHIUUPSFRVJSFUIFQVSDIBTFSUPEFMJWFSBUJUT
FYQFOTFUIFBMMFHFEMZEFGFDUJWFQSPEVDUUP(PBMTFUUFSGPSUFTUJOHSFQBJSPSSFQMBDFNFOU
(PBMTFUUFSTIBMMOPUCFSFTQPOTJCMFGPSBOZFYQFOTFTBTTPDJBUFEXJUIUIFSFQMBDFNFOUPS
removal of the product from its application for such delivery.
5)&8"33"/5:*470*%*'5)&130%6$5)"4#&&/%"."(&%#:"$$*%&/564&
'03163104&4'038)*$)*5*4/05*/5&/%&%"45)&3&46-50'*.1301&3
*/45"--"5*0/'"*-63&50'0--08*/45"--"5*0/$"3&03."*/5&/"/$&
*/4536$5*0/41307*%&%8*5)5)&130%6$564&0'1"354/051307*%&%#:
(0"-4&55&34:45&.403"/:.0%*'*$"5*0/0'"/:130%6$5#:5)&$6450.&3
6/-&44"11307&%#:(0"-4&55&34:45&.4*/$0305)&3$"64&4/05"3*4*/(
0650'%&'&$54*/."5&3*"-403803,."/4)*1
5IFTPMFPCMJHBUJPOPG(PBMTFUUFS4ZTUFNT*ODBOEUIFFYDMVTJWFSFNFEZVOEFSUIF
applicable warranty, is repair or replacement of any component part determined by
Goalsetter Systems, Inc. to be defective and covered by the warranty. Goalsetter Systems,
*ODXJMMOPUCFMJBCMFGPSBOZPUIFSEBNBHFTPSFYQFOTFT5IFBQQMJDBCMFXBSSBOUZJT
FYQSFTTMZJOMJFVPGBMMPUIFSXBSSBOUJFTFYQSFTTPSJNQMJFE(PBMTFUUFS4ZTUFNT*ODEPFT
not assume, and no other person or representative is authorized to assume for Goalsetter
Systems, Inc. any other liability in connection with the sale of Goalsetter System™ products.
NOT COVERED BY WARRANTY
t6TFJOOPOSFTJEFOUJBMBQQMJDBUJPOTPG(MBTTCBDLCPBSETPO4JHOBUVSF4FSJFTTZTUFNT
t6TFJOOPOSFTJEFOUJBMBQQMJDBUJPOTPG&YUSFNF4FSJFTBOE5PVSOBNFOU4FSJFTDPNQMFUF
systems.
t"OZQSPEVDUTTVCKFDUFEUPBCVTFOFHMJHFODFJNQSPQFSJOTUBMMBUJPOWBOEBMJTNBDUTPG(PE
alteration of product and any other events beyond the control of Goalsetter Systems, Inc.
t+VOJPS4FSJFTCSFBLBHFDBVTFECZUIFBDUPGEVOLJOH
t1BJOUPSSVTUFEQBSUT5PVDIVQQBJOUJTJODMVEFEJOBMMIBSEXBSFLJUT
t%FUFSJPSBUJPOPGQSPEVDUEVFUPUJNFPSXFBSBOEUFBS
Normal deterioration of products due to atmospheric conditions, weather, wear and tear
(including scratching or scuffing paint from normal use), or other causes that do not affect
functional use are not covered by Goalsetter Systems, Inc. warranties. All warranties are
valid only when product is used in the intended application & when installed according
to Goalsetter Systems instructions. Warranty may be void if maintenance instructions in
UIF0XOFST.BOVBMBSFOPUGPMMPXFE*GZPVEJEOPUSFDFJWFBO0XOFST.BOVBMQMFBTFDBMM
BOEPOFXJMMCFNBJMFEUPZPV
DISCLAIMERS: 5)&"11-*$"#-&8"33"/5:*4&913&44-:*/-*&60'"--
05)&38"33"/5*&4&913&4403*.1-*&%"/%"--05)&38"33"/*5&4"3&
)&3&#:%*4$-"*.&%*/$-6%*/(#65/05-*.*5&%505)&*.1-*&%8"33"/5*&4
0'.&3$)"/5"#*-*5:"/%'*5/&44'03"1"35*$6-"3163104&6/%&3/0
$*3$6.45"/$&44)"--(0"-4&55&34:45&.4*/$#&-*"#-&'03"/:*/%*3&$5
$0/4&26&/5*"-41&$*"-*/$*%&/5"-16/*5*7&03&9&.1-"3:%"."(&40'"/:
,*/%
5)&130%6$5*4*/5&/%&%50#&64&%501-":5)&410350'#"4,&5#"--
"--410354*/70-7&3*4,0'*/+63:5)&64&3"446.&4"--3*4,0'*/+63:
3&46-5*/('30.5)&64&0'5)*4130%6$5"--130%6$54"3&40-%0/5)*4
$0/%*5*0/"/%/03&13&4&/5"5*7&0'5)&$0.1"/:.":8"*7&03$)"/(&5)*4
POLICY.
4PNFTUBUFTEPOPUBMMPXUIFFYDMVTJPOPSMJNJUBUJPOPGJNQMJFEXBSSBOUJFTPSDPOTFRVFOUJBM
PSJODJEFOUBMEBNBHFTTPUIFBCPWFMJNJUBUJPOTPSFYDMVTJPOTNBZOPUBQQMZUPZPV
LEGAL REMEDIES: This warranty gives you specific legal rights, and you may also have
other rights which may vary from state to state.
WARRANTY CLAIMS: All returns must be arranged through the Goalsetter Systems, Inc.
dealer where the product was originally purchased. Warranties do not cover dealer service
DIBSHFTMBCPSDIBSHFTGSFJHIUDIBSHFTBOEUSBWFMFYQFOTFTBTTPDJBUFEXJUISFQMBDFNFOU
repair or removal of warranty items. Photos of the damaged product prior to any repair
or clean-up actions must clearly show and permit analysis of the damaged product by
Goalsetter Systems, Inc. A Goalsetter®Warranty Claim form must be completed, and photos
submitted, together with proof of purchase, for any item you wish to claim under warranty.
*GUIFQVSDIBTFXBTOPUNBEFUISPVHIBEFBMFSUIJTGPSNJTBWBJMBCMFCZFNBJMGBYPSNBJM
In response to your claim, you will receive an order confirmation as well as a notice stating
whether Goalsetter Systems, Inc. needs your warranty item returned. Goalsetter Systems,
*ODXJMMOPUJGZZPVCZGBYPSQIPOFJGXFEFUFSNJOFUIBUUIFJUFNDBOOPUCFDMBJNFEVOEFS
warranty. Goalsetter Systems, Inc. is not responsible for any charges for labor to install
or repair defective product without prior authorization. Goalsetter Systems, Inc. will
determine the most economical method to either repair or replace product before any
work is to commence.
Questions or Comments?
1IPOF
'BY
Email:info@goalsetter.com
www.goalsetter.com
(0"-4&55&3®BOE(0"-4&55&3#"4,&5#"--MPHPBSFSFHJTUFSFEUSBEFNBSLTPG
(PBMTFUUFS4ZTUFNT*ODJOUIF6OJUFE4UBUFT(0"-4&55&34:45&.45.BOE#&45*/
#"4,&5#"--5. are trademarks of Goalsetter Systems, Inc.
Thisproductiscovered by variousU.S.andCanadian patents, includingU.S.Patent#5,211,393.
Patent infringement will be prosecuted.
No part of this manual may be reproduced in any form or by any means electronic or
mechanical, including photocopying, recording, or by any information storage and retrieval
TZTUFNTXJUIPVUUIFFYQSFTTXSJUUFODPOTFOUPG(PBMTFUUFS4ZTUFNT*OD
Copyright 2006.
All rights reserved.
3FWJTFE
(4*.;$
Other manuals for GS72
1
This manual suits for next models
3
Table of contents
Other Goalsetter Systems Fitness Equipment manuals