Goodwe ET Series User manual

Quick Installation Guide
V1.0-2022-08-30
Hybrid Inverter
ET Series
(GW15K-ET | GW20K-ET | GW25K-ET | GW29.9K-ET | GW30K-ET)

1
PV String Safety:
1. Ensure the component frames and the bracket system are securely grounded.
2. Connect the DC cables using the delivered PV connectors. The manufacturer shall not be
liable for equipment damage if other connectors are used.
3. Ensure the DC cables are connected tightly, securely, and correctly. Inappropriate wiring may
cause poor contacts or high impedances, and damage the inverter.
4. Measure the DC cable using the multimeter to avoid reverse polarity connection. Also, the
voltage should be under the max DC input voltage. The manufacturer shall not be liable for
the damage caused by reverse connection and extremely high voltage.
5. The PV strings cannot be grounded. Ensure the minimum insulation resistance of the
PV string to the ground meets the minimum insulation resistance requirements before
connecting the PV string to the inverter. R=Max. Input Voltage (V)/30mA.
6. The PV modules used with the inverter must have an IEC61730 class A rating.
General Disclaimer
Safety Disclaimer
Warning
• The information in this quick installation guide is subject to change due to product updates
or other reasons. This guide cannot replace the product labels or the safety precautions in
the user manual unless otherwise specied. All descriptions here are for guidance only.
• Before installations, read through the quick installation guide. For additional information,
please see the user manual.
• All operations should be performed by trained and knowledgeable technicians who are
familiar with local standards and safety regulations.
• Check the deliverables for correct model, complete contents, and intact appearance. Contact
the manufacturer if any damage is found or any component is missing.
• Use insulating tools and wear personal protective equipment when operating the equipment
to ensure personal safety. Wear anti-static gloves, clothes, and wrist strip when touching
electronic components to protect the inverter from damage. The manufacturer shall not be
liable for any damage caused by static electricity.
• Strictly follow the installation, operation, and conguration instructions in this guide and user
manual. The manufacturer shall not be liable for equipment damage or personal injury if you
do not follow the instructions. For more warranty details, please visit https://en.goodwe.com/
warranty.
01 Safety Precautions
Inverter Safety:
1. The voltage and frequency at the connecting point should meet the on-grid requirements.
2. Additional protective devices like circuit breakers or fuses are recommended on the AC side.
Specication of the protective device should be at least 1.25 times the rated AC output rated
current.
3. PE cable of the inverter must be connected rmly. When there are multiple inverters, make
sure that all the grounding points on the enclosures are equipotential bonding.
4. Do not start the BACK-UP function if there is no battery in the PV system. The manufacturer
shall not be liable for the risks caused by not following this rule.
5. Do not apply mechanical load to the terminals, otherwise the terminals can be damaged.

2
HIGH VOLTAGE HAZARD.
Disconnect all incoming power
and turn o the product before
working on it.
Delayed discharge. Wait 5 minutes
after power o until the components
are completely discharged.
Read through the guide before
working on this device.
Potential risks exist. Wear proper
PPE before any operations.
High-temperature hazard. Do
not touch the product under
operation to avoid being burnt.
Grounding point. Indicates the
position for connecting the PE cable.
CE marking Do not dispose of the inverter
as household waste.Discard the
product in compliance with local
laws and regulations, or send it back
to the manufacturer.
5min
6. All labels and warning marks should be visible after the installation. Do not scrawl, damage,
or cover any label on the device.
7. Do not touch the running equipment to avoid being hurt as its temperature may exceed 60℃.
Do not install the equipment at a place within children's reach.
8. Unauthorized dismantling or modication may damage the equipment, the damage is not
covered under the warranty.
9. If there is any radio or wireless communication equipment below 30MHz near the inverter,
you have to:
• Install the inverter at least 30m far away from the wireless equipment.
• Add a low pass EMI lter or a multi winding ferrite core to the DC input cable or AC output
cable of the inverter.
10.Warning labels on the inverter are as follows.
Battery Safety:
1. The battery used with the inverter shall be approved by the inverter manufacturer. The
approved battery list can be obtained through the ocial website.
2. Before installations, read through the corresponding battery's User Manual to learn about
the product and the precautions. Strictly follow its requirements.
3. If the battery discharged completely, please charge it in strict accordance with the
corresponding model's User Manual.
4. The battery current may be inuenced by temperature, humidity, weather conditions, etc.,
which may limit the current and aect the load capacity.
5. If the battery cannot start properly, contact the after-sales service as soon as possible.
Otherwise, the battery will be damaged permanently.
6. Measure the DC cable using the multimeter to avoid reverse polarity connection. Also, the
voltage should be under the permissible range.
7. To avoid damage the inverter, do not connect one battery pack to multi inverters.

3
EU Declaration of Conformity
GoodWe Technologies Co., Ltd. hereby declares that the inverter with wireless communication
modules sold in the European market meets the requirements of the following directives:
• Radio Equipment Directive 2014/53/EU (RED)
• Restrictions of Hazardous Substances Directive 2011/65/EU and (EU) 2015/863 (RoHS)
• Waste Electrical and Electronic Equipment 2012/19/EU
• Registration, Evaluation, Authorization and Restriction of Chemicals (EC) No 1907/2006 (REACH)
GoodWe Technologies Co., Ltd. hereby declares that the inverter without wireless communication
modules sold in the European market meets the requirements of the following directives:
• Electromagnetic compatibility Directive 2014/30/EU (EMC)
• Electrical Apparatus Low Voltage Directive 2014/35/EU (LVD)
• Restrictions of Hazardous Substances Directive 2011/65/EU and (EU) 2015/863 (RoHS)
• Waste Electrical and Electronic Equipment 2012/19/EU
• Registration, Evaluation, Authorization and Restriction of Chemicals (EC) No 1907/2006 (REACH)
You can download the EU Declaration of Conformity on https://en.goodwe.com.
Check before Power-on
No. Check Item
1The product is rmly installed at a clean place that is well-ventilated and easy-to-
operate.
2The PE, DC input, AC output, and communication cables are connected correctly and
securely.
3 Cable ties are intact, routed properly and evenly.
4 Unused ports and terminals are sealed.
5The voltage and frequency at the connection point meet the inverter grid connection
requirements.

4
LED Indicators
Indicator Status Explanation
The inverter is power on and in the standby mode.
The inverter is starting up and in the self-check mode.
The inverter is in normal operation under grid-tied or o-
grid modes.
BACK-UP output overload.
A fault has occurred.
The inverter is powered o.
The grid is abnormal and the inverter is in o-grid mode.
The grid is normal and the inverter is in grid-tied mode.
BACK-UP is o.
The monitoring module of the inverter is resetting.
The inverter fails to connect with the communication
terminal device.
Faults between the communication terminal device and
Server.
The monitoring of the inverter operates well.
The monitoring module of the inverter has not been
started yet.

5
1. DC switch lock hole[1] 2. DC switch 3. PV input terminal
(PV+/-)
4. Communication
module port (COM) 5. METER communication
port 6. Communication port (COM2)
7. Battery input terminal
(BAT+/-) 8. BMS communication port 9. AC output terminal
(On-Grid and Back-Up)
10. Indicators 11. PE terminal 12. Handle
13. Mounting plate 14. Heat Sink
520mm
660mm
500mm
200mm 200mm
219.5mm
Parts
02 Product Introduction
Dimensions
1
2
3 4 5 6 7 8 9
10 11
13
12
14
13
[1]: Only for Australia.

6
L1 L2 L3 NPE
x 1 x 1
x 6
x N x 1 x 1
x 3
x 12
x 1
x 2
x N
x N
x 1 x 1 x N
x 1
x 1x 1x 1
x 1x 1 x 1
Packing List
Children No Touch
Inverter Installation
03
N = Quantity depends on the inverter model.
Space Requirements

7
1 2 3
D:80mm
φ:10mm
0%~100%RH
IP66
≥300mm
≥200mm ≥1000mm
≥500mm
≥300mm
Angle Requirements
Installing the Inverter

8
1
2
1
With handle:
Without handle:
5
5 6
M5
1.2~2N·m
3
3
04 Electrical Connection04
PE Cable
1
23
M5
1.2~2N·m
L=L1+(1-2)mm
Copper, 4mm2≤S≤6mm2
L1
4
Only for
Australia.
4
Only for
Australia.

9
12
23
1
1
11-13mm
70-80mm
Φ: 21-26mm
Copper, 10mm2≤S≤16mm2
1
2
34
1
1
2
5M6
3-4N·m
2
4H8
2-3N·m
5
6
1
3
6
7
7
5
5
5
4
2
AC Cable (ON-GRID&BACK-UP)
BACK-UP
ON-GRID

10
1
2
7-8mm
7-8mm
Φ: 4-5mm
4mm2≤S≤6mm2
1
23
4
2
3
4
1
3
1
1
4 5
2
2
2
Click
≤1000V
DC Cable (PV)
Click

11
1
2
7-8mm
7-8mm
Φ: 5.5-8mm
10mm2
1
23
4
2
3
4
1
3
1
1
45
2
2
Battery Cable (BAT)
Click
Click

12
11 12 13 14 15 16
1 2
2
5
6
4
3
1
1
6-8mm
25mm
Φ: 6mm
1
2
3
4 5 6 7 8 9 10
11 12 13 14 15 16
3
2
3
1
1
1
3
4
5
6
4
2
2
1
2
3
4 5 6 7
8
9
10
11
12
13
14
15
16
DRED/RCR:
11: COM/DRM0
12: REFGEN
13: DRM 4/8
14: DRM 3/7
15: DRM 2/6
16: DRM 1/5
Dry Contact
1: REY_OUT2-
2: NC
3:REY_OUT2+
9: REY_OUT3-
10: REY_OUT3+
Power Supply
4: GND
5: 12V_S
RSD Control
5: 12V_S
6: RSD_12V
Remote
Shutdown
7: GND
8: I01
4 5 6 7 8 9 10
11
12 13 14 15 16
1
2
3
Communication Connection
05
Communication Cable (PIN terminal)

13
Communication Cable (RJ45 network cable)
2
1
3
4
5
6
2
2
EMS/PAR
EMS/PAR
PIN Color EMS/PAR
1 Orange&White 485A3
2 Orange 485B3
3 Green&White NC
4 Blue GND
5 Blue&White CAN_L
6 Green CAN_H
7 Brown&White SYN_BUS1
8Brown SYN_BUS2
1
2
5
6
4
3
1
1
PIN Color Smart Meter BMS1 BMS2
1 Orange&White NC 485_A2 485_A4
2Orange NC 485_B2 485_B4
3 Green&White NC NC NC
4 Blue NC CANH1 CANH2
5 Blue&White NC CANL1 CANL2
6 Green NC NC NC
7 Brown&White 485_B1 NC NC
8Brown 485_A1 NC NC
BMS or Smart Meter

14
Communication Module (Optional)
Bluetooth Kit module: standard. WiFi Kit, LAN Kit, 4G Kit module: optional.

15
Power On and O
06
Power On
Power O
Turn on
Turn o
2
4
35
1
PV string
Battery breaker
AC breaker
Power meter Utility grid
CT
Load
breaker
ON-GRID loads
ON-GRID
BACK-UP loads
BACK-UP
Single-pole double throw (SPDT) switch
Battery

16
play
App Store
PV Master APP
<10m
<5m
PV Master
Commissioning and Monitoring07
Commissioning via PV Master APP
Monitoring via SEMS Portal App
play
App Store
SEMS Portal APP
SEMS Portal
For more detailed instructions, scan the QR codes below.
ET Series 15-30kW
User Manual
PV Master
User Manual
SEMS Portal
User Manual
WiFi Quick
Installation Guide

340-00840-00 Local Contacts
Ocal Website
GoodWe Technologies Co., Ltd.
No. 90 Zijin Rd., New District, Suzhou, 215011, China
www.goodwe.com
[email protected]