Goodwe HK1000 User manual

(HK1000/HK3000)
Quick Installation Guide
Smart Meter
V1.1-2022-06-28

1
Quick Installation Guide V1.1 -2022 -06-28
• The information in this quick installation guide is subject to change due to product
updates or other reasons. All descriptions here are for guidance only.
• Before installations, read through the quick installation guide.
• All operations should be performed by trained and knowledgeable technicians who are
familiar with local standards and safety regulations.
• Check the deliverables for correct model, complete contents, and intact appearance.
Contact the manufacturer if any damage is found or any component is missing.
• Strictly follow the installation, operation, and conguration instructions in this guide
and user manual. The manufacturer shall not be liable for equipment damage or
personal injury if you do not follow the instructions. For more warranty details, please
visit https://en.goodwe.com/warranty.
Safety Precautions
General Disclaimer
01
• Makesurethatthedeviceispoweredo󽗈beforeanyoperations.
• Ensurethecablesareconnectedtightly,securely,andcorrectly.Inappropriatewiringmay
causepoorcontactordamagethedevice.
• Additionalcircuitbreakersarerecommendedonthevoltageinputsidetoavoidpersonal
injuryordevicedamage.
• Speci󽗉cationoftheprotectivefuseshouldbe0.5A.
• Inareasatriskoflightning,ifthedevicecableexceeds10mandwiredwithoutgrounded
metalconduits,youarerecommendedtouseanexternallightningprotectiondevice.
Safety Disclaimer
WARINING
Check before Power-on
No. Check Item
1The product is rmly installed at a clean place that is well-ventilated and easy-
to-operate.
2The input power cables, CT Cables, and communication cables are connected
correctly and securely.
3 Cable ties are intact, routed properly and evenly.

2
Quick Installation Guide V1.1 -2022 -06-28
Storage
If the equipment is not to be installed or used immediately, please ensure that the storage
environment meets the following requirements:
• Do not unpack the outer package or throw the desiccant away.
• Store the equipment in a clean place. Make sure the temperature and humidity are
appropriate and no condensation.
• If the smart meter has been long term stored, it should be checked by professionals
before being put into use.
The module sold in the European market meets the following directives and requirements:
• Radio Equipment Directive 2014/53/EU (RED)
• Restrictions of Hazardous Substances Directive 2011/65/EU and (EU) 2015/863 (RoHS)
• Waste Electrical and Electronic Equipment 2012/19/EU
• Registration, Evaluation, Authorization and Restriction of Chemicals (EC) No 1907/2006
(REACH)
You can download the EU Declaration of Conformity on https://en.goodwe.com.
EU Declaration of Conformity
02

3
Quick Installation Guide V1.1 -2022 -06-28
Technical Parameters
03
Model HK1000 HK3000
Input
Grid Single phase Three phase
Voltage
Nominal Voltage (Vac) 110/230 230/400
Voltage Range (V) 100-240
Nominal AC Grid
Frequency (Hz) 50/60
Current CT In (A) 1CT: 120 3CTs: 120/200
Communication WiFi or LAN, RS485
Communication Distance (m) WiFi: 10, LAN: 100, RS485: 1000
Wireless
Parameters
Frequency Range 2.412GHz-2.472GHz
Supported Standards 802.11b/g/n
RF Outpower(dBm) < 20
User Interface 3 LED, Reset button
Accuracy
Voltage/Current Class 1
Active Energy Class 1
Reactive Energy Class 2
Power Consumption(W) < 5
Structural
Parameters
Dimensions (W×H×D mm) 72 × 85 × 66.5
Housing 4 modules
Weight (g) 320 500
Mounting DIN rail
Environment
Paraments
Ingress Protection Rating IP20
Operating Temperature Range (℃) -25 - +60
Storage Temperature Range (℃) -25 - +60
Relative Humidity (non-condensing) < 95%
Max. Operating Altitude (m) 2000

4
Quick Installation Guide V1.1 -2022 -06-28
CT
Indicators
Reserved Port
Reset Button
Note:
CT3 - and CT3 + only for HK3000.
Product Introduction
04

5
Quick Installation Guide V1.1 -2022 -06-28
Packing List
Smart Meter x 1 Screwdriver x 1 USB Plug x 1 PIN terminal x 4
Antenna x 1
installation and Cable Connection
1
1
24
3
6
5
Reset
SMARTMETER
USB
HOMEKIT
Installation
05

6
Quick Installation Guide V1.1 -2022 -06-28
HK1000
• Recommended cable connected to the voltage input terminal: 1mm2(17AWG).
• Do not remove the short circuit wire between L1 and L2.
• CT direction: House (K)-->Grid (L).
Loads
Fuse 0.5A
Household
Meter
Utility
Grid
Inverter
PV
Router
CT1
CT2
Network Cable
WiFi Antenna
Wiring System
06

7
Quick Installation Guide V1.1 -2022 -06-28
HK3000
CT
Inverter
Loads
Utility Grid
Household
Meter
Fuse 0.5A
• Recommended cable connected to the voltage input terminal: 1mm2(17AWG).
• CT direction: House (K)-->Grid (L).
PV
Router
Network Cable
WiFi Antenna

8
Quick Installation Guide V1.1 -2022 -06-28
Indicator Status Description
Steady on Power on
O Power o
Blinking The communication between HomeKit and the inverter is
normal.
O No communication between HomeKit and the inverter.
Double Blink HomeKit is trying to connect to the router.
Quadruple Blink HomeKit is trying to connect to the server.
Steady on HomeKit has been connected to the server successfully.
O Parameters for connecting HomeKit to the router or the
server have not been set.
Indicators
Reset Button
Press Time Description
1-3s Reset the HomeKit communication module.
5s-10s Reset HomeKit congurations.
>15s Initialize HomeKit and clear the historical energy data.
Power ON
Step 1 Connect the HomeKit cables.
Step 2 Power on the inverter and make sure that the inverter is working normally. Then the
HomeKit is powered on.
Commissioning
07
For more detailed instructions, scan the QR codes below.
SEMS Portal User
Manual
Wi-Fi/LAN Kit Quick
Installation Guide
Connect the HomeKit device to the router via WiFi or LAN. For details about seting related
parameters, refer to the Wi-Fi/LAN Kit Quick Installation Guide.
Commissioning the HomeKit

GoodWe Technologies Co., Ltd.
No. 90 Zijin Rd., New District, Suzhou, 215011, China
www.goodwe.com
[email protected]
Ocial Website
Local Contacts