Graco Ultra Max II 695 Manual

www.graco.be
GRACO N.V.• Industrieterrein Oude Bunders • Slakweidestraat 31 • B-3630 Maasmechelen
Tel. [phone] • Fax [phone]
• E-mail: [e-mail]
109 111 113 115 119 121
207 209 211 213 215 217 219 221 223 225
307 309 311 313 315 317 319 321 323 325 327
409 411 413 415 417 419 421 423 425 427
509 511 513 515 517 519 521 523 525 527
609 611 613 615 617 619 621 623 625 627
721 723 725
815 817 819 821 827
917
.20 .33 .49 .69 .91 1.17 1.47 2.15 2.54 2.96 3.42
200 (orange) 100 (blue) 60 (black) 30 (grey)
100 (orange) 100
(orange)
60 (blue)
5 cm
235 10 cm
331 15 cm
429 433 435 439 443 451 455 20 cm
529 531 533 543 551 555 25 cm
629 631 633 635 645 655 30 cm
729 735 35 cm
831 833 835 40 cm
935 45 cm
3.90 4.42 4.98 6.18 7.51 8.23 10.5712.99
none
none
ULTRA
®
MAX II 695/795/1095
MARK V™- MARK X™
SETUP
Connect hose to sprayer and gun.
Tighten hose connections with wrench. Unscrew tip & guard from gun.
Fill throat packing nut with TSL™
to prevent premature packing wear.
Make sure power
switch is set to OFF.
Plug electrical cord
into grounded outlet.
Turn prime valve
to Prime position (down).
Place siphon tube in pail
partially filled with water.
Turn pressure control knob
to lowest pressure, and set
power switch to ON.
Increase pressure until
sprayer starts and water
runs out of prime tube.
Let water run out of
prime tube for 15 seconds.
Decrease pressure
until sprayer stops.
Turn prime valve
to Spray position
(horizontal).
Make sure safety
lever of gun is OFF.
Aim gun at inside
wall of water pail
and squeeze trigger.
Increase pressure
until sprayer starts.
Keep gun triggered into
water pail for 1 minute.
Release trigger.
Turn prime
valve to Prime
position (down).
Place siphon tube in paint
pail, but leave drain tube
in water pail.
Aim gun at inside
wall of water pail,
and squeeze trigger.
Transfer drain
tube to paint pail.
Increase pressure until
sprayer starts and paint
comes out of drain tube.
Keeping gun triggered into
water pail, turn prime valve
to Spray position (horizontal).
When paint comes out of gun,
release trigger and turn safety
lever of gun to ON.
Screw tip & guard onto gun, making sure
arrow-shaped handle of tip is pointing forward.
You can reverse this tip to quickly clear clogs
without taking it apart.
This procedure is for water-base paints and flushing fluids. For solvent-base paints and flushing
fluids (i.e.mineral spirits), you must read Fire and Explosion Hazard in the Operating Instructions.
* check the Graco operations manual delive red with the unit for more deta i l s.
CHOOSE THE RIGHT TIP (286-XXX) & FILTER
WARNING
Flow Rate(l/min.)
Pump Filter (mesh)
Gun Filter (mesh)
Quick Operator’s Guide

SPRAYING
Turn safety lever
of gun to OFF.
Point gun at area to be sprayed about 30 cm from surface, and begin moving gun before triggering.
A good spray pattern is evenly distributed as it hits surface. Set pressure just high enough to spray without heavy edges.
Use smaller tip size for thinner material and a larger tip size for thicker material if pressure adjustment cannot achieve even spray pattern.
SHUTDOWN AND CLEANUP * for AutoClean2™:see bottom of this page
Set power
switch to OFF.
Trigger gun until
pressure is relieved.
Turn prime valve
to Prime position
(down).
Remove gun filter
assembly.
Unscrew tip & guard
from gun. Clean gun filter,
inlet screen, tip, guard
and manifold filter with
water and brush.
Set power switch to ON,
and increase pressure
until sprayer starts.
As soon as Pump Armor
comes out of drain tube,
set power switch to OFF.
Screw inlet screen onto
siphon tube, replace
manifold filter and spacer,
and assemble gun with
filter, tip and guard.
Wipe outside of sprayer,
hose and gun with rag
soaked in water or
mineral spirits.
Fill throat packing nut
with TSL™
Place drain
tube and
siphon tube
in pail of water.
Turn pressure control knob
to lowest setting,set power
switch to ON, and increase
pressure until sprayer starts.
Let sprayer run and flush itself
for 2 minutes.
Keeping gun triggered
into water pail, turn prime
valve to Spray position
(horizontal).
Set power switch to OFF,
turn pressure control knob to
lowest setting,and turn prime
valve to Prime position (down).
Place drain tube in waste
pail and siphon tube in
container of Pump Armor™
Assemble gun
without filter.
Unscrew inlet screen
from siphon tube.
Keep gun triggered
into pail for 1 minute,
until water coming
out of gun is clean.
Remove manifold
filter and spacer.
GRACO N.V.• Industrieterrein Oude Bunders
Slakweidestraat 31 • B-3630 Maasmechelen
Tel. [phone] • Fax [phone]
Al l in fo r m a t i o n , i l l u s t r a t i o n s , a n d s p ec if i cat i ons in t h is d oc um en t a re ba sed o n t he lat e st p ro du ct i nfo r m a t i o n
a v ail abl e at th e time o f pu bl ica tion. The r ight is re s e r ved to ma ke changes at a ny tim e wit ho ut notice.
© 2002, 2006 Graco N.V.· Form No.328006 E (rev.B)· 07/06 · Printed in Europe.
Graco is registered ISO 9001.
Remove suction and drain tubes from
paint. Place drain tube into waste pail
and wipe suction tube clean.
Place suction tube in
appropriate cleaning fluid.
Close drain valve.
Switch power ON.
To save paint from hose and pump,
trigger gun into paint pail and increase
pressure.When cleaning fluid appears,
release gun trigger.
Turn pressure all the way down.
Open drain valve.
Screw connector
onto gun.
Rotate trigger lock
clip 90° to lock
trigger open.
Press display button
until timer appears and turn
pressure control knob to highest.
Close drain valve.
With clean fluid, briefly trigger gun
into waste pail several times to
clear any debris from front of gun.
Install tip and guard and briefly trigger
gun into waiste pail to clean tip.
Reverse tip if necessary.
Place gun in
AutoClean connector.
Slide open end
over back of handle.
AUTOCLEAN2™GUIDE
When finished, remove
trigger clip from gun handle.
Unscrew connector from gun.
Remove gun from connector.